* - Added new SCSI_ASENSE_NOT_READY_TO_READY_CHANGE constant to the Mass Storage class driver, to indicate when a previously
* not ready removable medium has now become ready for the host's use (thanks to Martin Degelsegger)
* - Moved the Pipe and Endpoint stream related code to two new USB library core source files EndpointStream.c and PipeStream.c
+ * - Added new USB_Device_GetFrameNumber() and USB_Host_GetFrameNumber() functions to retrieve the current USB frame number
+ * - Added new USB_Host_EnableSOFEvents(), USB_Host_DisableSOFEvents() and EVENT_USB_Host_StartOfFrame() for the user application
+ * handling of USB Start of Frame events while in USB Host mode
+ * - Added new PRNT_Host_BytesReceived(), PRNT_Host_ReceiveByte(), PRNT_Host_SendByte() and PRNT_Host_Flush() functions to the
+ * Print Host Class driver
+ * - Added class specific descriptor alternative struct type defines with standard USB-IF element naming
+ * - Added new project makefile template to the library and moved board driver stub files into in a new "CodeTemplates" directory
+ * - Added board hardware driver support for the Olimex AVR-USB-162 development board (thanks to Steve Fawcett)
+ * - Added board hardware driver support for the Kernel Concepts USBFOO development board
+ * - Added board hardware driver support for the Linnix UDIP development board
+ * - Added board hardware driver support for the Busware BUI development board
+ * - Added board hardware driver support for the Arduino Uno development board
+ * - Added board hardware driver support for the Busware CUL V3 868MHZ radio board (thanks to Dirk Tostmann)
+ * - Added board hardware driver support for the Blackcat USB JTAG board (thanks to the PSGroove team)
+ * - Added board hardware driver support for the Maximus board (thanks to the PSGroove team)
+ * - Added board hardware driver support for the Minimus board (thanks to the PSGroove team)
+ * - Added default test tone generation mode to the Device mode AudioInput demos
+ * - Added new NO_CLASS_DRIVER_AUTOFLUSH compile time option to disable automatic flushing of interfaces when the USB management
+ * tasks for each driver is called
+ * - Added standard keyboard HID report scancode defines (thanks to Laszlo Monda)
+ * - Added new Pipe_GetBusyBanks(), Endpoint_GetBusyBanks() and Endpoint_AbortPendingIN() functions
+ * - Added new NO_BLOCK_SUPPORT, NO_EEPROM_BYTE_SUPPORT, NO_FLASH_BYTE_SUPPORT and NO_LOCK_BYTE_WRITE_SUPPORT compile time options to the
+ * CDC class bootloader
*
* <b>Changed:</b>
* - Removed complicated logic for the Endpoint_ConfigureEndpoint() function to use inlined or function called versions
* not break communications with the host by exceeding the maximum control request stage timeout period
* - Changed the signature of the CALLBACK_USB_GetDescriptor() callback function so that the descriptor pointer is const, to remove
* the need for extra casting inside the callback (thanks to Jonathan Kollasch)
+ * - Reduced HOST_DEVICE_SETTLE_DELAY_MS to 1000ms down from 1500ms to improve device compatibility while in USB Host mode
+ * - Changed over all demos, drivers and internal functions to use the current frame number over the Start of Frame flag where possible
+ * to free up the Start of Frame flag for interrupt use in the user application
+ * - All project makefiles now correctly clean intermediate build files from assembly and C++ sources (thanks to Daniel Czigany)
+ * - Removed the EVENT_USB_InitFailure() event, not specifying a USB mode correctly now defaults to UID selection mode
+ * - Renamed and moved class driver common constant definitions to make the naming scheme more uniform
+ * - Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive
+ * - Changed configuration descriptor parser for all host mode projects and class drivers to ensure better compatibility with devices
+ * - Moved the USB mode specifier constants into a new enum, so that they are semantically related to one another
+ * - Renamed ENDPOINT_DOUBLEBANK_SUPPORTED() to ENDPOINT_BANKS_SUPPORTED() and changed it to return the maximum number of supported banks for
+ * the given endpoint
+ * - Better algorithm to extract and convert the internal device serial number into a string descriptor (if present)
+ * - All USB class drivers are now automatically included when LUFA/Drivers/USB.h is included, and no longer need to be seperately included
+ * - All LowLevel demos changed to use the constants and types defined in the USB class drivers
+ * - Changed AudioInput and AudioOutput demos to reload the next sample via an interrupt rather than polling the sample timer
+ * - The MIDI class drivers now automatically flushes the MIDI interface when the MIDI class driver's USBTask() function is called
+ * - Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times
*
* <b>Fixed:</b>
* - Fixed USB_GetHIDReportItemInfo() function modifying the given report item's data when the report item does not exist
* in the USB controller if the endpoints or pipes were allocated in anything other than ascending order (thanks to Martin Degelsegger)
* - Fixed USBtoSerial and Benito project SetLineEncoding calls failing if the USART is busy, due to the RX ISR delaying the control
* request handler
+ * - Fixed LowLevel PrinterHost demo not sending control requests to the attached printer with the correct printer interface wIndex value
+ * - Added LEDs_ToggleLEDs() function to several board LED drivers which were missing it (thanks to Andrei Krainev)
+ * - Fixed SET FEATURE and CLEAR FEATURE control requests directed at an unconfigured endpoint causing request timeouts
+ * - Fixed incorrect signature reported in the CDC class bootloader for the ATMEGA32U2
+ * - Fixed USB_Host_ClearPipeStall() incorrectly determining the endpoint direction from the currently selected pipe
+ * - Fixed JTAG_DEBUG_POINT() and JTAG_DEBUG_BREAK() macros not compiling under pure C99 standards mode
+ * - Fixed endpoint selection within the CALLBACK_HID_Device_CreateHIDReport() callback function causing broken GET REPORT requests
+ * - Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target
+ * - Fixed BootloaderCDC project failing on some operating systems due to removed Line Encoding options (thanks to Alexey Belyaev)
+ * - Fixed incorrect LEDs_ChangeLEDs() function in the Benito board LED driver
+ * - Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set
+ * - Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used
+ * - Fixed SPI driver not explicitly setting /SS and MISO pins as inputs when SPI_Init() is called
+ * - Fixed ISR definition conflict in the XPLAIN bridge between the software UART and the AVRISP-MKII ISP modules
+ * - Fixed random enumeration failure while in device mode due to interrupts causing the Set Address request to exceed maximum timings
+ * - Fixed MIDI_Host_Flush() not aborting early when the specified MIDI host interface was not configured
+ * - Fixed MIDI class driver send routines silently discarding packets if the endpoint or pipe is busy (thanks to Robin Green)
*
* \section Sec_ChangeLog100807 Version 100807
* <b>New:</b>
* read (thanks to Andrei Krainev)
* - Fixed device state not being reset back to the default state if the host sets the address to 0
* - Fixed Set Configuration requests not being stalled until the host has set the device's address
- * - Fixed Host mode HID class driver not sending the correct report type when HID_Host_SendReportByID() was called and the
+ * - Fixed Host mode HID class driver not sending the correct report type when HID_Host_SendReportByID() was called and the
* HID_HOST_BOOT_PROTOCOL_ONLY compile time option is set
* - Fixed INTERRUPT_CONTROL_ENDPOINT compile time option preventing other interrupts from occurring while the control endpoint
* request is being processed, causing possible lockups if a USB interrupt occurs during a transfer
* - Fixed Mass Storage Host Class driver and Low Level demo not clearing the error condition if an attached device returns a
* STALL to a GET MAX LUN request (thanks to Martin Luxen)
* - Fixed TeensyHID bootloader not properly shutting down the USB interface to trigger a disconnection on the host before resetting
- * - Fixed MassStorageHost Class driver demo not having USB_STREAM_TIMEOUT_MS compile time option set properly to prevent slow
+ * - Fixed MassStorageHost Class driver demo not having USB_STREAM_TIMEOUT_MS compile time option set properly to prevent slow
* devices from timing out the data pipes
* - Fixed the definition of the Endpoint_BytesInEndpoint() macro for the U4 series AVR parts
* - Fixed MIDI host Class driver MIDI_Host_SendEventPacket() routine not properly checking for Pipe ready before writing
* - Added new Pipe_IsFrozen() macro to determine if the currently selected pipe is frozen
* - Added new USB_GetHIDReportSize() function to the HID report parser to retrieve the size of a given report by its ID
* - Added new combined Mass Storage and Keyboard demo (thanks to Matthias Hullin)
- *
+ *
* <b>Changed:</b>
* - SetIdle requests to the HID device driver with a 0 idle period (send changes only) now only affect the requested
* HID interface within the device, not all HID interfaces
* - Added new Pipe_BoundEndpointNumber() and Pipe_IsEndpointBound() functions
* - Added new DEVICE_STATE_AS_GPIOR and HOST_STATE_AS_GPIOR compile time options
* - Added 404 Not Found errors to the webserver in the RNDIS demos to indicate invalid URLs
- *
+ *
* <b>Changed:</b>
* - Deprecated pseudo-scheduler and removed dynamic memory allocator from the library (first no longer needed and second unused)
* - The device-mode CALLBACK_USB_GetDescriptor() function now has an extra parameter so that the memory space in which the requested
* - Changed HWB board driver to Buttons driver, to allow for the support of future boards with more than one mounted GPIO button
* - Serial driver now correctly calculates the baud register value when in double speed mode
* - Init function of the Serial driver is now static inline to product smaller code for the common-case of static init values
- *
+ *
*
* \section Sec_ChangeLog090401 Version 090401
*
* - Doxygen documentation now contains documentation on all the projects, bootloaders and most demos included with the library
* - CDC bootloader now runs user application when USB disconnected rather than waiting for a hard reset
* - MouseHostWithParser and KeyboardHostWithParser now support multiple-report devices
- * - RNDIS demo can now close connections correctly using the new TCP_APP_CLOSECONNECTION() macro - used in Webserver
+ * - RNDIS demo can now close connections correctly using the new TCP_APP_CLOSECONNECTION() macro - used in Webserver
* - Fixed the DFU bootloader, no longer freezes up when certain files are programmed into an AVR, made reading/writing faster
- * - Fixed mouse/joystick up/down movements reversed - HID mouse X/Y coordinates use a left-handed coordinate system, not a normal
+ * - Fixed mouse/joystick up/down movements reversed - HID mouse X/Y coordinates use a left-handed coordinate system, not a normal
* right-handed system
* - Added stub code to the CDC and USBtoSerial demos showing how to read and set the RS-232 handshake lines - not currently used in
* the demos, but the example code and supporting defines are now in place
* - All HID demos now pass the USB.org automated HID compliance tests
* - Polling interval of the interrupt endpoint in the CDC based demos changed to 0xFF to fix problems on Linux systems
* - Changed stream functions to accept a new callback function, with NO_STREAM_CALLBACKS used to disable all callbacks
- * - Mass Storage demo dataflash management routines changed to use the endpoint stream functions
+ * - Mass Storage demo dataflash management routines changed to use the endpoint stream functions
* - Added AVRStudio project files for each demo in addition to the existing Programmer's Notepad master project file
* - Re-added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes
* are reflected in the hardware (change was previously lost)
*
* - Added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes
* are reflected in the hardware
- * - Fixed CDC and USBtoSerial demos - Stream commands do not work for control endpoints, and the
+ * - Fixed CDC and USBtoSerial demos - Stream commands do not work for control endpoints, and the
* GetLineCoding request had an incorrect RequestType mask preventing it from being processed
* - Improved reliability of the USBtoSerial demo, adding a busy wait while the buffer is full
* - Device control endpoint size is now determined from the device's descriptors rather than being fixed
* - ID transition interrupt now raises the appropriate device/host disconnect event if device attached
* - Fixed double VBUS change (and VBUS -) event when detaching in device mode
* - Added ability to disable ANSI terminal codes by the defining of DISABLE_TERMINAL_CODES in makefile
- * - Removed return from ConfigurePipe and ConfigureEndpoint functions - use Pipe_IsConfigured() and
+ * - Removed return from ConfigurePipe and ConfigureEndpoint functions - use Pipe_IsConfigured() and
* Endpoint_IsConfigured() after calling the config functions to determine success
*/
+
projects / pub / lufa.git / blobdiff