firmware/bootloaderconfig.h

   1 /* Name: bootloaderconfig.h
   2  * Project: USBaspLoader
   3  * Author: Christian Starkjohann
   4  * Creation Date: 2007-12-08
   5  * Tabsize: 4
   6  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
   7  * License: GNU GPL v2 (see License.txt)
   8  * This Revision: $Id: bootloaderconfig.h 729 2009-03-20 09:03:58Z cs $
   9  */
  10
  11 #ifndef __bootloaderconfig_h_included__
  12 #define __bootloaderconfig_h_included__
  13
  14 /*
  15 General Description:
  16 This file (together with some settings in Makefile) configures the boot loader
  17 according to the hardware.
  18
  19 This file contains (besides the hardware configuration normally found in
  20 usbconfig.h) two functions or macros: bootLoaderInit() and
  21 bootLoaderCondition(). Whether you implement them as macros or as static
  22 inline functions is up to you, decide based on code size and convenience.
  23
  24 bootLoaderInit() is called as one of the first actions after reset. It should
  25 be a minimum initialization of the hardware so that the boot loader condition
  26 can be read. This will usually consist of activating a pull-up resistor for an
  27 external jumper which selects boot loader mode.
  28
  29 bootLoaderCondition() is called immediately after initialization and in each
  30 main loop iteration. If it returns TRUE, the boot loader will be active. If it
  31 returns FALSE, the boot loader jumps to address 0 (the loaded application)
  32 immediately.
  33
  34 For compatibility with Thomas Fischl's avrusbboot, we also support the macro
  35 names BOOTLOADER_INIT and BOOTLOADER_CONDITION for this functionality. If
  36 these macros are defined, the boot loader usees them.
  37 */
  38
  39 /* ---------------------------- Hardware Config ---------------------------- */
  40
  41 #define USB_CFG_IOPORTNAME      D
  42 /* This is the port where the USB bus is connected. When you configure it to
  43  * "B", the registers PORTB, PINB and DDRB will be used.
  44  */
  45 #define JUMPER_BIT              7       /* old value was 0 */
  46 /*
  47  * jumper is connected to this bit in port D, active low
  48  */
  49 #define USB_CFG_DMINUS_BIT      6       /* old value was 4 */
  50 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
  51  * This may be any bit in the port.
  52  */
  53 #define USB_CFG_DPLUS_BIT       2
  54 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
  55  * This may be any bit in the port. Please note that D+ must also be connected
  56  * to interrupt pin INT0!
  57  */
  58 #define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
  59 /* Clock rate of the AVR in MHz. Legal values are 12000, 16000 or 16500.
  60  * The 16.5 MHz version of the code requires no crystal, it tolerates +/- 1%
  61  * deviation from the nominal frequency. All other rates require a precision
  62  * of 2000 ppm and thus a crystal!
  63  * Default if not specified: 12 MHz
  64  */
  65
  66 /* ----------------------- Optional Hardware Config ------------------------ */
  67
  68 /* #define USB_CFG_PULLUP_IOPORTNAME   D */
  69 /* If you connect the 1.5k pullup resistor from D- to a port pin instead of
  70  * V+, you can connect and disconnect the device from firmware by calling
  71  * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
  72  * This constant defines the port on which the pullup resistor is connected.
  73  */
  74 /* #define USB_CFG_PULLUP_BIT          4 */
  75 /* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
  76  * above) where the 1.5k pullup resistor is connected. See description
  77  * above for details.
  78  */
  79
  80 /* ------------------------------------------------------------------------- */
  81 /* ---------------------- feature / code size options ---------------------- */
  82 /* ------------------------------------------------------------------------- */
  83
  84 #define HAVE_READ_LOCK_FUSE         1
  85 /*
  86  * enable the loaders capability to load its lfuse, hfuse and lockbits
  87  * ...However, programming of these is prohibited...
  88  */
  89
  90 #define HAVE_BLB11_SOFTW_LOCKBIT    1
  91 /*
  92  * The IC itself do not need to prgra BLB11, but the bootloader will avaoid
  93  * to erase itself from the bootregion
  94  */
  95
  96 #define HAVE_SPMINTEREFACE          1
  97 /*
  98  * Since code within normal section of application memory (rww-section) is
  99  * not able to call spm for programming flash-pages, this option (when
 100  * enabled) will insert a small subroutine into the bootloader-section
 101  * to enable applications to circumvent this limitation and make them
 102  * able to program the flash in a similar way as the bootloader does, too.
 103  * For further details see "spminterface.h", which implements this
 104  * feature.
 105  */
 106
 107 #define HAVE_EEPROM_PAGED_ACCESS    1
 108 /* If HAVE_EEPROM_PAGED_ACCESS is defined to 1, page mode access to EEPROM is
 109  * compiled in. Whether page mode or byte mode access is used by AVRDUDE
 110  * depends on the target device. Page mode is only used if the device supports
 111  * it, e.g. for the ATMega88, 168 etc. You can save quite a bit of memory by
 112  * disabling page mode EEPROM access. Costs ~ 138 bytes.
 113  */
 114 #define HAVE_EEPROM_BYTE_ACCESS     1
 115 /* If HAVE_EEPROM_BYTE_ACCESS is defined to 1, byte mode access to EEPROM is
 116  * compiled in. Byte mode is only used if the device (as identified by its
 117  * signature) does not support page mode for EEPROM. It is required for
 118  * accessing the EEPROM on the ATMega8. Costs ~54 bytes.
 119  */
 120 #define BOOTLOADER_CAN_EXIT         0
 121 /* If this macro is defined to 1, the boot loader will exit shortly after the
 122  * programmer closes the connection to the device. Costs ~36 bytes.
 123  */
 124 #define HAVE_CHIP_ERASE             0
 125 /* If this macro is defined to 1, the boot loader implements the Chip Erase
 126  * ISP command. Otherwise pages are erased on demand before they are written.
 127  */
 128 //#define SIGNATURE_BYTES             0x1e, 0x93, 0x07, 0     /* ATMega8 */
 129 /* This macro defines the signature bytes returned by the emulated USBasp to
 130  * the programmer software. They should match the actual device at least in
 131  * memory size and features. If you don't define this, values for ATMega8,
 132  * ATMega88, ATMega168 and ATMega328 are guessed correctly.
 133  */
 134
 135 /* The following block guesses feature options so that the resulting code
 136  * should fit into 2k bytes boot block with the given device and clock rate.
 137  * Activate by passing "-DUSE_AUTOCONFIG=1" to the compiler.
 138  * This requires gcc 3.4.6 for small enough code size!
 139  */
 140 #if USE_AUTOCONFIG
 141 #   undef HAVE_EEPROM_PAGED_ACCESS
 142 #   define HAVE_EEPROM_PAGED_ACCESS     (USB_CFG_CLOCK_KHZ >= 16000)
 143 #   undef HAVE_EEPROM_BYTE_ACCESS
 144 #   define HAVE_EEPROM_BYTE_ACCESS      1
 145 #   undef BOOTLOADER_CAN_EXIT
 146 #   define BOOTLOADER_CAN_EXIT          1
 147 #   undef SIGNATURE_BYTES
 148 #endif /* USE_AUTOCONFIG */
 149
 150 /* ------------------------------------------------------------------------- */
 151
 152 /* Example configuration: Port D bit 3 is connected to a jumper which ties
 153  * this pin to GND if the boot loader is requested. Initialization allows
 154  * several clock cycles for the input voltage to stabilize before
 155  * bootLoaderCondition() samples the value.
 156  * We use a function for bootLoaderInit() for convenience and a macro for
 157  * bootLoaderCondition() for efficiency.
 158  */
 159
 160 #ifndef __ASSEMBLER__   /* assembler cannot parse function definitions */
 161
 162 #ifndef MCUCSR          /* compatibility between ATMega8 and ATMega88 */
 163 #   define MCUCSR   MCUSR
 164 #endif
 165
 166 static inline void  bootLoaderInit(void)
 167 {
 168     DDRD   = 0;
 169     PORTD  = (1 << JUMPER_BIT);     /* activate pull-up */
 170 //     deactivated by Stephan - reset after each avrdude op is annoing!
 171 //     if(!(MCUCSR & (1 << EXTRF)))    /* If this was not an external reset, ignore */
 172 //         leaveBootloader();
 173     MCUCSR = 0;                     /* clear all reset flags for next time */
 174 }
 175
 176 static inline void  bootLoaderExit(void)
 177 {
 178     PORTD = 0;                      /* undo bootLoaderInit() changes */
 179 }
 180
 181 #define bootLoaderCondition()           ((PIND & (1 << JUMPER_BIT)) == 0)
 182
 183 #endif /* __ASSEMBLER__ */
 184
 185 /* ------------------------------------------------------------------------- */
 186
 187 #endif /* __bootloader_h_included__ */