-# Hey Emacs, this is a -*- makefile -*-\r
-#----------------------------------------------------------------------------\r
-# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.\r
-# >> Modified for use with the LUFA project. <<\r
-#\r
-# Released to the Public Domain\r
-#\r
-# Additional material for this makefile was written by:\r
-# Peter Fleury\r
-# Tim Henigan\r
-# Colin O'Flynn\r
-# Reiner Patommel\r
-# Markus Pfaff\r
-# Sander Pool\r
-# Frederik Rouleau\r
-# Carlos Lamas\r
-# Dean Camera\r
-# Opendous Inc.\r
-# Denver Gingerich\r
-#\r
-#----------------------------------------------------------------------------\r
-# On command line:\r
-#\r
-# make all = Make software.\r
-#\r
-# make clean = Clean out built project files.\r
-#\r
-# make coff = Convert ELF to AVR COFF.\r
-#\r
-# make extcoff = Convert ELF to AVR Extended COFF.\r
-#\r
-# make program = Download the hex file to the device, using avrdude.\r
-# Please customize the avrdude settings below first!\r
-#\r
-# make dfu = Download the hex file to the device, using dfu-programmer (must\r
-# have dfu-programmer installed).\r
-#\r
-# make flip = Download the hex file to the device, using Atmel FLIP (must\r
-# have Atmel FLIP installed).\r
-#\r
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer\r
-# (must have dfu-programmer installed).\r
-#\r
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP\r
-# (must have Atmel FLIP installed).\r
-#\r
-# make doxygen = Generate DoxyGen documentation for the project (must have\r
-# DoxyGen installed)\r
-#\r
-# make debug = Start either simulavr or avarice as specified for debugging, \r
-# with avr-gdb or avr-insight as the front end for debugging.\r
-#\r
-# make filename.s = Just compile filename.c into the assembler code only.\r
-#\r
-# make filename.i = Create a preprocessed source file for use in submitting\r
-# bug reports to the GCC project.\r
-#\r
-# To rebuild project do "make clean" then "make all".\r
-#----------------------------------------------------------------------------\r
-\r
-\r
-# MCU name\r
-MCU = at90usb647\r
-\r
-\r
-# Target board (see library "Board Types" documentation, USER or blank for projects not requiring\r
-# LUFA board drivers). If USER is selected, put custom board drivers in a directory called \r
-# "Board" inside the application directory.\r
-BOARD = USBKEY\r
-\r
-\r
-# Processor frequency.\r
-# This will define a symbol, F_CPU, in all source code files equal to the \r
-# processor frequency. You can then use this symbol in your source code to \r
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done\r
-# automatically to create a 32-bit value in your source code.\r
-# Typical values are:\r
-# F_CPU = 1000000\r
-# F_CPU = 1843200\r
-# F_CPU = 2000000\r
-# F_CPU = 3686400\r
-# F_CPU = 4000000\r
-# F_CPU = 7372800\r
-# F_CPU = 8000000\r
-# F_CPU = 11059200\r
-# F_CPU = 14745600\r
-# F_CPU = 16000000\r
-# F_CPU = 18432000\r
-# F_CPU = 20000000\r
-F_CPU = 8000000\r
-\r
-\r
-# Input clock frequency.\r
-# This will define a symbol, F_CLOCK, in all source code files equal to the \r
-# input clock frequency (before any prescaling is performed). This value may\r
-# differ from F_CPU if prescaling is used on the latter, and is required as the\r
-# raw input clock is fed directly to the PLL sections of the AVR for high speed\r
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'\r
-# at the end, this will be done automatically to create a 32-bit value in your\r
-# source code.\r
-#\r
-# If no clock division is performed on the input clock inside the AVR (via the\r
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.\r
-F_CLOCK = $(F_CPU)\r
-\r
-\r
-# Output format. (can be srec, ihex, binary)\r
-FORMAT = ihex\r
-\r
-\r
-# Target file name (without extension).\r
-TARGET = PrinterHost\r
-\r
-\r
-# Object files directory\r
-# To put object files in current directory, use a dot (.), do NOT make\r
-# this an empty or blank macro!\r
-OBJDIR = .\r
-\r
-\r
-# Path to the LUFA library\r
-LUFA_PATH = ../../../..\r
-\r
-\r
-# LUFA library compile-time options\r
-LUFA_OPTS = -D USE_NONSTANDARD_DESCRIPTOR_NAMES\r
-LUFA_OPTS += -D USB_HOST_ONLY\r
-LUFA_OPTS += -D NO_STREAM_CALLBACKS\r
-LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"\r
-\r
-\r
-# List C source files here. (C dependencies are automatically generated.)\r
-SRC = $(TARGET).c \\r
- ConfigDescriptor.c \\r
- Lib/PrinterCommands.c \\r
- $(LUFA_PATH)/LUFA/Drivers/Peripheral/SerialStream.c \\r
- $(LUFA_PATH)/LUFA/Drivers/Peripheral/Serial.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/DevChapter9.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Endpoint.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Host.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/HostChapter9.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/LowLevel.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Pipe.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/Events.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBInterrupt.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBTask.c \\r
- $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/ConfigDescriptor.c \\r
-\r
-\r
-# List C++ source files here. (C dependencies are automatically generated.)\r
-CPPSRC = \r
-\r
-\r
-# List Assembler source files here.\r
-# Make them always end in a capital .S. Files ending in a lowercase .s\r
-# will not be considered source files but generated files (assembler\r
-# output from the compiler), and will be deleted upon "make clean"!\r
-# Even though the DOS/Win* filesystem matches both .s and .S the same,\r
-# it will preserve the spelling of the filenames, and gcc itself does\r
-# care about how the name is spelled on its command-line.\r
-ASRC =\r
-\r
-\r
-# Optimization level, can be [0, 1, 2, 3, s]. \r
-# 0 = turn off optimization. s = optimize for size.\r
-# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)\r
-OPT = s\r
-\r
-\r
-# Debugging format.\r
-# Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.\r
-# AVR Studio 4.10 requires dwarf-2.\r
-# AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.\r
-DEBUG = dwarf-2\r
-\r
-\r
-# List any extra directories to look for include files here.\r
-# Each directory must be seperated by a space.\r
-# Use forward slashes for directory separators.\r
-# For a directory that has spaces, enclose it in quotes.\r
-EXTRAINCDIRS = $(LUFA_PATH)/\r
-\r
-\r
-# Compiler flag to set the C Standard level.\r
-# c89 = "ANSI" C\r
-# gnu89 = c89 plus GCC extensions\r
-# c99 = ISO C99 standard (not yet fully implemented)\r
-# gnu99 = c99 plus GCC extensions\r
-CSTANDARD = -std=gnu99\r
-\r
-\r
-# Place -D or -U options here for C sources\r
-CDEFS = -DF_CPU=$(F_CPU)UL -DF_CLOCK=$(F_CLOCK)UL -DBOARD=BOARD_$(BOARD) $(LUFA_OPTS)\r
-\r
-\r
-# Place -D or -U options here for ASM sources\r
-ADEFS = -DF_CPU=$(F_CPU)\r
-\r
-\r
-# Place -D or -U options here for C++ sources\r
-CPPDEFS = -DF_CPU=$(F_CPU)UL\r
-#CPPDEFS += -D__STDC_LIMIT_MACROS\r
-#CPPDEFS += -D__STDC_CONSTANT_MACROS\r
-\r
-\r
-\r
-#---------------- Compiler Options C ----------------\r
-# -g*: generate debugging information\r
-# -O*: optimization level\r
-# -f...: tuning, see GCC manual and avr-libc documentation\r
-# -Wall...: warning level\r
-# -Wa,...: tell GCC to pass this to the assembler.\r
-# -adhlns...: create assembler listing\r
-CFLAGS = -g$(DEBUG)\r
-CFLAGS += $(CDEFS)\r
-CFLAGS += -O$(OPT)\r
-CFLAGS += -funsigned-char\r
-CFLAGS += -funsigned-bitfields\r
-CFLAGS += -ffunction-sections\r
-CFLAGS += -fpack-struct\r
-CFLAGS += -fshort-enums\r
-CFLAGS += -finline-limit=20\r
-CFLAGS += -Wall\r
-CFLAGS += -Wstrict-prototypes\r
-CFLAGS += -Wundef\r
-#CFLAGS += -fno-unit-at-a-time\r
-#CFLAGS += -Wunreachable-code\r
-#CFLAGS += -Wsign-compare\r
-CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)\r
-CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))\r
-CFLAGS += $(CSTANDARD)\r
-\r
-\r
-#---------------- Compiler Options C++ ----------------\r
-# -g*: generate debugging information\r
-# -O*: optimization level\r
-# -f...: tuning, see GCC manual and avr-libc documentation\r
-# -Wall...: warning level\r
-# -Wa,...: tell GCC to pass this to the assembler.\r
-# -adhlns...: create assembler listing\r
-CPPFLAGS = -g$(DEBUG)\r
-CPPFLAGS += $(CPPDEFS)\r
-CPPFLAGS += -O$(OPT)\r
-CPPFLAGS += -funsigned-char\r
-CPPFLAGS += -funsigned-bitfields\r
-CPPFLAGS += -fpack-struct\r
-CPPFLAGS += -fshort-enums\r
-CPPFLAGS += -fno-exceptions\r
-CPPFLAGS += -Wall\r
-CFLAGS += -Wundef\r
-#CPPFLAGS += -mshort-calls\r
-#CPPFLAGS += -fno-unit-at-a-time\r
-#CPPFLAGS += -Wstrict-prototypes\r
-#CPPFLAGS += -Wunreachable-code\r
-#CPPFLAGS += -Wsign-compare\r
-CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)\r
-CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))\r
-#CPPFLAGS += $(CSTANDARD)\r
-\r
-\r
-#---------------- Assembler Options ----------------\r
-# -Wa,...: tell GCC to pass this to the assembler.\r
-# -adhlns: create listing\r
-# -gstabs: have the assembler create line number information; note that\r
-# for use in COFF files, additional information about filenames\r
-# and function names needs to be present in the assembler source\r
-# files -- see avr-libc docs [FIXME: not yet described there]\r
-# -listing-cont-lines: Sets the maximum number of continuation lines of hex \r
-# dump that will be displayed for a given single line of source input.\r
-ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100\r
-\r
-\r
-#---------------- Library Options ----------------\r
-# Minimalistic printf version\r
-PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min\r
-\r
-# Floating point printf version (requires MATH_LIB = -lm below)\r
-PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt\r
-\r
-# If this is left blank, then it will use the Standard printf version.\r
-PRINTF_LIB = \r
-#PRINTF_LIB = $(PRINTF_LIB_MIN)\r
-#PRINTF_LIB = $(PRINTF_LIB_FLOAT)\r
-\r
-\r
-# Minimalistic scanf version\r
-SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min\r
-\r
-# Floating point + %[ scanf version (requires MATH_LIB = -lm below)\r
-SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt\r
-\r
-# If this is left blank, then it will use the Standard scanf version.\r
-SCANF_LIB = \r
-#SCANF_LIB = $(SCANF_LIB_MIN)\r
-#SCANF_LIB = $(SCANF_LIB_FLOAT)\r
-\r
-\r
-MATH_LIB = -lm\r
-\r
-\r
-# List any extra directories to look for libraries here.\r
-# Each directory must be seperated by a space.\r
-# Use forward slashes for directory separators.\r
-# For a directory that has spaces, enclose it in quotes.\r
-EXTRALIBDIRS = \r
-\r
-\r
-\r
-#---------------- External Memory Options ----------------\r
-\r
-# 64 KB of external RAM, starting after internal RAM (ATmega128!),\r
-# used for variables (.data/.bss) and heap (malloc()).\r
-#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff\r
-\r
-# 64 KB of external RAM, starting after internal RAM (ATmega128!),\r
-# only used for heap (malloc()).\r
-#EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff\r
-\r
-EXTMEMOPTS =\r
-\r
-\r
-\r
-#---------------- Linker Options ----------------\r
-# -Wl,...: tell GCC to pass this to linker.\r
-# -Map: create map file\r
-# --cref: add cross reference to map file\r
-LDFLAGS = -Wl,-Map=$(TARGET).map,--cref\r
-LDFLAGS += -Wl,--relax \r
-LDFLAGS += -Wl,--gc-sections\r
-LDFLAGS += $(EXTMEMOPTS)\r
-LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))\r
-LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)\r
-#LDFLAGS += -T linker_script.x\r
-\r
-\r
-\r
-#---------------- Programming Options (avrdude) ----------------\r
-\r
-# Programming hardware: alf avr910 avrisp bascom bsd \r
-# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500\r
-#\r
-# Type: avrdude -c ?\r
-# to get a full listing.\r
-#\r
-AVRDUDE_PROGRAMMER = jtagmkII\r
-\r
-# com1 = serial port. Use lpt1 to connect to parallel port.\r
-AVRDUDE_PORT = usb\r
-\r
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex\r
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep\r
-\r
-\r
-# Uncomment the following if you want avrdude's erase cycle counter.\r
-# Note that this counter needs to be initialized first using -Yn,\r
-# see avrdude manual.\r
-#AVRDUDE_ERASE_COUNTER = -y\r
-\r
-# Uncomment the following if you do /not/ wish a verification to be\r
-# performed after programming the device.\r
-#AVRDUDE_NO_VERIFY = -V\r
-\r
-# Increase verbosity level. Please use this when submitting bug\r
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> \r
-# to submit bug reports.\r
-#AVRDUDE_VERBOSE = -v -v\r
-\r
-AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)\r
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)\r
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)\r
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)\r
-\r
-\r
-\r
-#---------------- Debugging Options ----------------\r
-\r
-# For simulavr only - target MCU frequency.\r
-DEBUG_MFREQ = $(F_CPU)\r
-\r
-# Set the DEBUG_UI to either gdb or insight.\r
-# DEBUG_UI = gdb\r
-DEBUG_UI = insight\r
-\r
-# Set the debugging back-end to either avarice, simulavr.\r
-DEBUG_BACKEND = avarice\r
-#DEBUG_BACKEND = simulavr\r
-\r
-# GDB Init Filename.\r
-GDBINIT_FILE = __avr_gdbinit\r
-\r
-# When using avarice settings for the JTAG\r
-JTAG_DEV = /dev/com1\r
-\r
-# Debugging port used to communicate between GDB / avarice / simulavr.\r
-DEBUG_PORT = 4242\r
-\r
-# Debugging host used to communicate between GDB / avarice / simulavr, normally\r
-# just set to localhost unless doing some sort of crazy debugging when \r
-# avarice is running on a different computer.\r
-DEBUG_HOST = localhost\r
-\r
-\r
-\r
-#============================================================================\r
-\r
-\r
-# Define programs and commands.\r
-SHELL = sh\r
-CC = avr-gcc\r
-OBJCOPY = avr-objcopy\r
-OBJDUMP = avr-objdump\r
-SIZE = avr-size\r
-AR = avr-ar rcs\r
-NM = avr-nm\r
-AVRDUDE = avrdude\r
-REMOVE = rm -f\r
-REMOVEDIR = rm -rf\r
-COPY = cp\r
-WINSHELL = cmd\r
-\r
-# Define Messages\r
-# English\r
-MSG_ERRORS_NONE = Errors: none\r
-MSG_BEGIN = -------- begin --------\r
-MSG_END = -------- end --------\r
-MSG_SIZE_BEFORE = Size before: \r
-MSG_SIZE_AFTER = Size after:\r
-MSG_COFF = Converting to AVR COFF:\r
-MSG_EXTENDED_COFF = Converting to AVR Extended COFF:\r
-MSG_FLASH = Creating load file for Flash:\r
-MSG_EEPROM = Creating load file for EEPROM:\r
-MSG_EXTENDED_LISTING = Creating Extended Listing:\r
-MSG_SYMBOL_TABLE = Creating Symbol Table:\r
-MSG_LINKING = Linking:\r
-MSG_COMPILING = Compiling C:\r
-MSG_COMPILING_CPP = Compiling C++:\r
-MSG_ASSEMBLING = Assembling:\r
-MSG_CLEANING = Cleaning project:\r
-MSG_CREATING_LIBRARY = Creating library:\r
-\r
-\r
-\r
-\r
-# Define all object files.\r
-OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o) \r
-\r
-# Define all listing files.\r
-LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst) \r
-\r
-\r
-# Compiler flags to generate dependency files.\r
-GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d\r
-\r
-\r
-# Combine all necessary flags and optional flags.\r
-# Add target processor to flags.\r
-ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)\r
-ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)\r
-ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)\r
-\r
-\r
-\r
-\r
-\r
-# Default target.\r
-all: begin gccversion sizebefore build checkhooks checklibmode checkboard sizeafter end\r
-\r
-# Change the build target to build a HEX file or a library.\r
-build: elf hex eep lss sym\r
-#build: lib\r
-\r
-\r
-elf: $(TARGET).elf\r
-hex: $(TARGET).hex\r
-eep: $(TARGET).eep\r
-lss: $(TARGET).lss\r
-sym: $(TARGET).sym\r
-LIBNAME=lib$(TARGET).a\r
-lib: $(LIBNAME)\r
-\r
-\r
-\r
-# Eye candy.\r
-# AVR Studio 3.x does not check make's exit code but relies on\r
-# the following magic strings to be generated by the compile job.\r
-begin:\r
- @echo\r
- @echo $(MSG_BEGIN)\r
-\r
-end:\r
- @echo $(MSG_END)\r
- @echo\r
-\r
-\r
-# Display size of file.\r
-HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex\r
-ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf\r
-MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )\r
-FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )\r
-\r
-sizebefore:\r
- @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \\r
- 2>/dev/null; echo; fi\r
-\r
-sizeafter:\r
- @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \\r
- 2>/dev/null; echo; fi\r
-\r
-checkhooks: build\r
- @echo\r
- @echo ------- Unhooked LUFA Events -------\r
- @$(shell) (grep -s '^EVENT_.*LUFA/.*\\.o' $(TARGET).map | \\r
- cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \\r
- echo "(None)"\r
- @echo ------------------------------------\r
-\r
-checklibmode:\r
- @echo\r
- @echo ----------- Library Mode -----------\r
- @$(shell) ($(CC) $(ALL_CFLAGS) -E -dM - < /dev/null \\r
- | grep 'USB_\(DEVICE\|HOST\)_ONLY' | cut -d' ' -f2 | grep ".*") \\r
- || echo "No specific mode (both device and host mode allowable)."\r
- @echo ------------------------------------\r
-\r
-checkboard:\r
- @echo\r
- @echo ---------- Selected Board ----------\r
- @echo Selected board model is $(BOARD).\r
- @echo ------------------------------------\r
- \r
-# Display compiler version information.\r
-gccversion : \r
- @$(CC) --version\r
-\r
-\r
-\r
-# Program the device. \r
-program: $(TARGET).hex $(TARGET).eep\r
- $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)\r
-\r
-flip: $(TARGET).hex\r
- batchisp -hardware usb -device $(MCU) -operation erase f\r
- batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program\r
- batchisp -hardware usb -device $(MCU) -operation start reset 0\r
-\r
-dfu: $(TARGET).hex\r
- dfu-programmer $(MCU) erase\r
- dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex\r
- dfu-programmer $(MCU) reset\r
-\r
-flip-ee: $(TARGET).hex $(TARGET).eep\r
- copy $(TARGET).eep $(TARGET)eep.hex\r
- batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase\r
- batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program\r
- batchisp -hardware usb -device $(MCU) -operation start reset 0\r
-\r
-dfu-ee: $(TARGET).hex $(TARGET).eep\r
- dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep\r
- dfu-programmer $(MCU) reset\r
-\r
-\r
-# Generate avr-gdb config/init file which does the following:\r
-# define the reset signal, load the target file, connect to target, and set \r
-# a breakpoint at main().\r
-gdb-config: \r
- @$(REMOVE) $(GDBINIT_FILE)\r
- @echo define reset >> $(GDBINIT_FILE)\r
- @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)\r
- @echo end >> $(GDBINIT_FILE)\r
- @echo file $(TARGET).elf >> $(GDBINIT_FILE)\r
- @echo target remote $(DEBUG_HOST):$(DEBUG_PORT) >> $(GDBINIT_FILE)\r
-ifeq ($(DEBUG_BACKEND),simulavr)\r
- @echo load >> $(GDBINIT_FILE)\r
-endif\r
- @echo break main >> $(GDBINIT_FILE)\r
-\r
-debug: gdb-config $(TARGET).elf\r
-ifeq ($(DEBUG_BACKEND), avarice)\r
- @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.\r
- @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \\r
- $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)\r
- @$(WINSHELL) /c pause\r
-\r
-else\r
- @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \\r
- $(DEBUG_MFREQ) --port $(DEBUG_PORT)\r
-endif\r
- @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)\r
-\r
-\r
-\r
-\r
-# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.\r
-COFFCONVERT = $(OBJCOPY) --debugging\r
-COFFCONVERT += --change-section-address .data-0x800000\r
-COFFCONVERT += --change-section-address .bss-0x800000\r
-COFFCONVERT += --change-section-address .noinit-0x800000\r
-COFFCONVERT += --change-section-address .eeprom-0x810000\r
-\r
-\r
-\r
-coff: $(TARGET).elf\r
- @echo\r
- @echo $(MSG_COFF) $(TARGET).cof\r
- $(COFFCONVERT) -O coff-avr $< $(TARGET).cof\r
-\r
-\r
-extcoff: $(TARGET).elf\r
- @echo\r
- @echo $(MSG_EXTENDED_COFF) $(TARGET).cof\r
- $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof\r
-\r
-\r
-\r
-# Create final output files (.hex, .eep) from ELF output file.\r
-%.hex: %.elf\r
- @echo\r
- @echo $(MSG_FLASH) $@\r
- $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@\r
-\r
-%.eep: %.elf\r
- @echo\r
- @echo $(MSG_EEPROM) $@\r
- -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \\r
- --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0\r
-\r
-# Create extended listing file from ELF output file.\r
-%.lss: %.elf\r
- @echo\r
- @echo $(MSG_EXTENDED_LISTING) $@\r
- $(OBJDUMP) -h -z -S $< > $@\r
-\r
-# Create a symbol table from ELF output file.\r
-%.sym: %.elf\r
- @echo\r
- @echo $(MSG_SYMBOL_TABLE) $@\r
- $(NM) -n $< > $@\r
-\r
-\r
-\r
-# Create library from object files.\r
-.SECONDARY : $(TARGET).a\r
-.PRECIOUS : $(OBJ)\r
-%.a: $(OBJ)\r
- @echo\r
- @echo $(MSG_CREATING_LIBRARY) $@\r
- $(AR) $@ $(OBJ)\r
-\r
-\r
-# Link: create ELF output file from object files.\r
-.SECONDARY : $(TARGET).elf\r
-.PRECIOUS : $(OBJ)\r
-%.elf: $(OBJ)\r
- @echo\r
- @echo $(MSG_LINKING) $@\r
- $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)\r
-\r
-\r
-# Compile: create object files from C source files.\r
-$(OBJDIR)/%.o : %.c\r
- @echo\r
- @echo $(MSG_COMPILING) $<\r
- $(CC) -c $(ALL_CFLAGS) $< -o $@ \r
-\r
-\r
-# Compile: create object files from C++ source files.\r
-$(OBJDIR)/%.o : %.cpp\r
- @echo\r
- @echo $(MSG_COMPILING_CPP) $<\r
- $(CC) -c $(ALL_CPPFLAGS) $< -o $@ \r
-\r
-\r
-# Compile: create assembler files from C source files.\r
-%.s : %.c\r
- $(CC) -S $(ALL_CFLAGS) $< -o $@\r
-\r
-\r
-# Compile: create assembler files from C++ source files.\r
-%.s : %.cpp\r
- $(CC) -S $(ALL_CPPFLAGS) $< -o $@\r
-\r
-\r
-# Assemble: create object files from assembler source files.\r
-$(OBJDIR)/%.o : %.S\r
- @echo\r
- @echo $(MSG_ASSEMBLING) $<\r
- $(CC) -c $(ALL_ASFLAGS) $< -o $@\r
-\r
-\r
-# Create preprocessed source for use in sending a bug report.\r
-%.i : %.c\r
- $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ \r
- \r
-\r
-# Target: clean project.\r
-clean: begin clean_list clean_binary end\r
-\r
-clean_binary:\r
- $(REMOVE) $(TARGET).hex\r
- \r
-clean_list:\r
- @echo $(MSG_CLEANING)\r
- $(REMOVE) $(TARGET).eep\r
- $(REMOVE) $(TARGET)eep.hex\r
- $(REMOVE) $(TARGET).cof\r
- $(REMOVE) $(TARGET).elf\r
- $(REMOVE) $(TARGET).map\r
- $(REMOVE) $(TARGET).sym\r
- $(REMOVE) $(TARGET).lss\r
- $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)\r
- $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)\r
- $(REMOVE) $(SRC:.c=.s)\r
- $(REMOVE) $(SRC:.c=.d)\r
- $(REMOVE) $(SRC:.c=.i)\r
- $(REMOVEDIR) .dep\r
-\r
-\r
-doxygen:\r
- @echo Generating Project Documentation...\r
- @doxygen Doxygen.conf\r
- @echo Documentation Generation Complete.\r
-\r
-clean_doxygen:\r
- rm -rf Documentation\r
-\r
-# Create object files directory\r
-$(shell mkdir $(OBJDIR) 2>/dev/null)\r
-\r
-\r
-# Include the dependency files.\r
--include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)\r
-\r
-\r
-# Listing of phony targets.\r
-.PHONY : all checkhooks checklibmode checkboard \\r
-begin finish end sizebefore sizeafter gccversion \\r
-build elf hex eep lss sym coff extcoff clean \\r
-clean_list clean_binary program debug gdb-config \\r
-doxygen dfu flip flip-ee dfu-ee
\ No newline at end of file
projects / pub / USBasp.git / commitdiff