Slight improvements to the reliability of the software UART in the XPLAINBridge project.

diff --git a/LUFA/Drivers/USB/Class/Device/CDC.c b/LUFA/Drivers/USB/Class/Device/CDC.c
index 69295e5..6eabb24 100644 (file)
--- a/LUFA/Drivers/USB/Class/Device/CDC.c
+++ b/LUFA/Drivers/USB/Class/Device/CDC.c
@@ -154,7 +154,7 @@ uint8_t CDC_Device_SendByte(USB_ClassInfo_CDC_Device_t* const CDCInterfaceInfo,
        Endpoint_SelectEndpoint(CDCInterfaceInfo->Config.DataINEndpointNumber);
 
        if (!(Endpoint_IsReadWriteAllowed()))
-       {       
+       {
                Endpoint_ClearIN();
 
                uint8_t ErrorCode;

diff --git a/Projects/XPLAINBridge/Lib/SoftUART.c b/Projects/XPLAINBridge/Lib/SoftUART.c
index ff152e7..81f0237 100644 (file)
--- a/Projects/XPLAINBridge/Lib/SoftUART.c
+++ b/Projects/XPLAINBridge/Lib/SoftUART.c
@@ -63,41 +63,38 @@ void SoftUART_Init(void)
        EICRA  = (1 << ISC01);
        EIMSK  = (1 << INT0);
 
-       /* Ensure that when the timer is enabled the transmission ISR runs immediately */
-       OCR1B  = TCNT1 + 1;
-       
-       /* Start timer 1 with transmission channel force-enabled so that it will immediatly fire */
-       TCCR1C = (1 << FOC1B);
-       TIMSK1 = (1 << OCIE1B);
+       /* Start software UART transmission and reception timers */
+       TIMSK3 = (1 << OCIE3A);
+       TCCR3B = (1 << CS30);
        TCCR1B = (1 << CS10);
 }
 
 /** ISR to detect the start of a bit being sent to the software UART. */
-ISR(INT0_vect)
+ISR(INT0_vect, ISR_BLOCK)
 {
        /* Set reception channel to fire 1.5 bits past the beginning of the start bit */
-       OCR1A = TCNT1 + ((BIT_TIME * 3) / 2);
-       
+       OCR1A = TCNT1 + (BIT_TIME + (BIT_TIME / 2));
+
        /* Clear the received data temporary variable, reset the current received bit position mask */
        RX_Data    = 0;
        RX_BitMask = (1 << 0);
 
-       /* Clear reception channel ISR flag in case it is pending */
-       TIFR1 = (1 << OCF1A);
-
        /* Check that the start bit is still low to prevent noise from triggering a reception */
        if (!(SRXPIN & (1 << SRX)))
-       {       
-               /* Still low, enable both send and receive channels */
-               TIMSK1 =  (1 << OCIE1A) | (1 << OCIE1B);
-               
-               /* Clear the start bit detection ISR flag if it is pending */
+       {
+               /* Clear reception channel ISR flag in case it is pending */
+               TIFR1 = (1 << OCF1A);
+
+               /* Still low, enable bit receive ISR */
+               TIMSK1 =  (1 << OCIE1A);                
+
+               /* Clear the start bit detection ISR flag */
                EIMSK &= ~(1 << INT0);
        }
 }
 
 /** ISR to manage the reception of bits to the software UART. */
-ISR(TIMER1_COMPA_vect)
+ISR(TIMER1_COMPA_vect, ISR_BLOCK)
 {
        /* Move the reception ISR compare position one bit ahead */
        OCR1A += BIT_TIME;
@@ -118,17 +115,17 @@ ISR(TIMER1_COMPA_vect)
                RingBuffer_Insert(&UARTtoUSB_Buffer, RX_Data);
        
                /* Disable the reception ISR as all data has now been received, re-enable start bit detection ISR */
-               TIMSK1  = (1 << OCIE1B);
-               EIMSK  |= (1 << INT0);
-               EIFR    = (1 << INTF0);
+               TIMSK1 = 0;
+               EIFR   = (1 << INTF0);
+               EIMSK  = (1 << INT0);
        }
 }
 
 /** ISR to manage the transmission of bits via the software UART. */
-ISR(TIMER1_COMPB_vect)
+ISR(TIMER3_COMPA_vect, ISR_NOBLOCK)
 {
        /* Move the transmission ISR compare position one bit ahead */
-       OCR1B += BIT_TIME;
+       OCR3A += BIT_TIME;
 
        /* Check if transmission has finished */
        if (TX_BitsRemaining)

diff --git a/Projects/XPLAINBridge/XPLAINBridge.c b/Projects/XPLAINBridge/XPLAINBridge.c
index 4f3583e..a0766f1 100644 (file)
--- a/Projects/XPLAINBridge/XPLAINBridge.c
+++ b/Projects/XPLAINBridge/XPLAINBridge.c
@@ -151,7 +151,7 @@ void SetupHardware(void)
        LEDs_Init();
        USB_Init();
        V2Protocol_Init();
-       
+
        /* Disable JTAG debugging */
        MCUCR |= (1 << JTD);
        MCUCR |= (1 << JTD);
@@ -166,6 +166,8 @@ void SetupHardware(void)
        /* Re-enable JTAG debugging */
        MCUCR &= ~(1 << JTD);
        MCUCR &= ~(1 << JTD);
+
+       CurrentFirmwareMode = MODE_USART_BRIDGE; // TEMP
 }
 
 /** Event handler for the library USB Configuration Changed event. */