-/** \file\r
- *\r
- * This file contains special DoxyGen information for the generation of the main page and other special\r
- * documentation pages. It is not a project source file.\r
- */\r
- \r
-/** \page Page_ProgrammingApps Programming an Application into a USB AVR\r
- *\r
- * Once you have built an application, you will need a way to program in the resulting ".HEX" file (and, if your\r
- * application uses EEPROM variables with initial values, also a ".EEP" file) into your USB AVR. Normally, the\r
- * reprogramming an AVR device must be performed using a special piece of programming hardware, through one of the\r
- * supported AVR programming protocols - ISP, HVSP, HVPP, JTAG or dW. This can be done through a custom programmer,\r
- * a third party programmer, or an official Atmel AVR tool - for more information, see the Atmel.com website.\r
- *\r
- * Alternatively, you can use the bootloader. From the Atmel factory, each USB AVR comes preloaded with the Atmel\r
- * DFU (Device Firmware Update) class bootloader, a small piece of AVR firmware which allows the remainder of the\r
- * AVR to be programmed through a non-standard interface such as the serial USART port, SPI, or (in this case) USB.\r
- * Bootloaders have the advantage of not requiring any special hardware for programming, and cannot usually be erased\r
- * or broken without an external programming device. They have disadvantages however; they cannot change the fuses of\r
- * the AVR (special configuration settings that control the operation of the chip itself) and a small portion of the\r
- * AVR's FLASH program memory must be reserved to contain the bootloader firmware, and thus cannot be used by the\r
- * loaded application. Atmel's DFU bootloader is either 4KB (for the smaller USB AVRs) or 8KB (for the larger USB AVRs).\r
- *\r
- * If you wish to use the DFU bootloader to program in your application, refer to your DFU programmer's documentation.\r
- * Atmel provides a free utility called FLIP which is USB AVR compatible, and an open source (Linux compatible)\r
- * alternative exists called "dfu-programmer".\r
- */
\ No newline at end of file
+/** \file
+ *
+ * This file contains special DoxyGen information for the generation of the main page and other special
+ * documentation pages. It is not a project source file.
+ */
+
+/** \page Page_ProgrammingApps Programming an Application into a USB AVR
+ *
+ * Once you have built an application, you will need a way to program in the resulting ".HEX" file (and, if your
+ * application uses EEPROM variables with initial values, also a ".EEP" file) into your USB AVR. Normally, the
+ * reprogramming of an AVR device must be performed using a special piece of programming hardware, through one of the
+ * supported AVR programming protocols - ISP, HVSP, HVPP, JTAG or dW. This can be done through a custom programmer,
+ * a third party programmer, or an official Atmel AVR tool - for more information, see the Atmel.com website.
+ *
+ * Alternatively, you can use the bootloader. From the Atmel factory, each USB AVR comes preloaded with the Atmel
+ * DFU (Device Firmware Update) class bootloader, a small piece of AVR firmware which allows the remainder of the
+ * AVR to be programmed through a non-standard interface such as the serial USART port, SPI, or (in this case) USB.
+ * Bootloaders have the advantage of not requiring any special hardware for programming, and cannot usually be erased
+ * or broken without an external programming device. They have disadvantages however; they cannot change the fuses of
+ * the AVR (special configuration settings that control the operation of the chip itself) and a small portion of the
+ * AVR's FLASH program memory must be reserved to contain the bootloader firmware, and thus cannot be used by the
+ * loaded application. Atmel's DFU bootloader is either 4KB (for the smaller USB AVRs) or 8KB (for the larger USB AVRs).
+ *
+ * If you wish to use the DFU bootloader to program in your application, refer to your DFU programmer's documentation.
+ * Atmel provides a free utility called FLIP which is USB AVR compatible, and an open source (Linux compatible)
+ * alternative exists called "dfu-programmer".
+ */
projects / pub / USBasp.git / blobdiff