X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/3bd4011c0935e0d41af3ae59c69eec989cc53bbf..77a9df36a77d2523dd2bc24fa17f9f04c6c175c5:/LUFA/ManPages/ProgrammingApps.txt

diff --git a/LUFA/ManPages/ProgrammingApps.txt b/LUFA/ManPages/ProgrammingApps.txt
index 1e3be715a..c1b2181c8 100644
--- a/LUFA/ManPages/ProgrammingApps.txt
+++ b/LUFA/ManPages/ProgrammingApps.txt
@@ -1,27 +1,27 @@
-/** \file
- *
- *  This file contains special DoxyGen information for the generation of the main page and other special
- *  documentation pages. It is not a project source file.
- */
- 
-/** \page Page_ProgrammingApps Programming an Application into a USB AVR
- *
- *  Once you have built an application, you will need a way to program in the resulting ".HEX" file (and, if your
- *  application uses EEPROM variables with initial values, also a ".EEP" file) into your USB AVR. Normally, the
- *  reprogramming an AVR device must be performed using a special piece of programming hardware, through one of the
- *  supported AVR programming protocols - ISP, HVSP, HVPP, JTAG or dW. This can be done through a custom programmer,
- *  a third party programmer, or an official Atmel AVR tool - for more information, see the Atmel.com website.
- *
- *  Alternatively, you can use the bootloader. From the Atmel factory, each USB AVR comes preloaded with the Atmel
- *  DFU (Device Firmware Update) class bootloader, a small piece of AVR firmware which allows the remainder of the
- *  AVR to be programmed through a non-standard interface such as the serial USART port, SPI, or (in this case) USB.
- *  Bootloaders have the advantage of not requiring any special hardware for programming, and cannot usually be erased
- *  or broken without an external programming device. They have disadvantages however; they cannot change the fuses of
- *  the AVR (special configuration settings that control the operation of the chip itself) and a small portion of the
- *  AVR's FLASH program memory must be reserved to contain the bootloader firmware, and thus cannot be used by the
- *  loaded application. Atmel's DFU bootloader is either 4KB (for the smaller USB AVRs) or 8KB (for the larger USB AVRs).
- *
- *  If you wish to use the DFU bootloader to program in your application, refer to your DFU programmer's documentation.
- *  Atmel provides a free utility called FLIP which is USB AVR compatible, and an open source (Linux compatible)
- *  alternative exists called "dfu-programmer".
- */
\ No newline at end of file
+/** \file
+ *
+ *  This file contains special DoxyGen information for the generation of the main page and other special
+ *  documentation pages. It is not a project source file.
+ */
+
+/** \page Page_ProgrammingApps Programming an Application into a USB AVR
+ *
+ *  Once you have built an application, you will need a way to program in the resulting ".HEX" file (and, if your
+ *  application uses EEPROM variables with initial values, also a ".EEP" file) into your USB AVR. Normally, the
+ *  reprogramming of an AVR device must be performed using a special piece of programming hardware, through one of the
+ *  supported AVR programming protocols - ISP, HVSP, HVPP, JTAG or dW. This can be done through a custom programmer,
+ *  a third party programmer, or an official Atmel AVR tool - for more information, see the Atmel.com website.
+ *
+ *  Alternatively, you can use the bootloader. From the Atmel factory, each USB AVR comes preloaded with the Atmel
+ *  DFU (Device Firmware Update) class bootloader, a small piece of AVR firmware which allows the remainder of the
+ *  AVR to be programmed through a non-standard interface such as the serial USART port, SPI, or (in this case) USB.
+ *  Bootloaders have the advantage of not requiring any special hardware for programming, and cannot usually be erased
+ *  or broken without an external programming device. They have disadvantages however; they cannot change the fuses of
+ *  the AVR (special configuration settings that control the operation of the chip itself) and a small portion of the
+ *  AVR's FLASH program memory must be reserved to contain the bootloader firmware, and thus cannot be used by the
+ *  loaded application. Atmel's DFU bootloader is either 4KB (for the smaller USB AVRs) or 8KB (for the larger USB AVRs).
+ *
+ *  If you wish to use the DFU bootloader to program in your application, refer to your DFU programmer's documentation.
+ *  Atmel provides a free utility called FLIP which is USB AVR compatible, and an open source (Linux compatible)
+ *  alternative exists called "dfu-programmer".
+ */