Demos/Host/ClassDriver/AndroidAccessoryHost/makefile

   1 # Hey Emacs, this is a -*- makefile -*-
   2 #----------------------------------------------------------------------------
   3 # WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
   4 #  >> Modified for use with the LUFA project. <<
   5 #
   6 # Released to the Public Domain
   7 #
   8 # Additional material for this makefile was written by:
   9 # Peter Fleury
  10 # Tim Henigan
  11 # Colin O'Flynn
  12 # Reiner Patommel
  13 # Markus Pfaff
  14 # Sander Pool
  15 # Frederik Rouleau
  16 # Carlos Lamas
  17 # Dean Camera
  18 # Opendous Inc.
  19 # Denver Gingerich
  20 #
  21 #----------------------------------------------------------------------------
  22 # On command line:
  23 #
  24 # make all = Make software.
  25 #
  26 # make clean = Clean out built project files.
  27 #
  28 # make coff = Convert ELF to AVR COFF.
  29 #
  30 # make extcoff = Convert ELF to AVR Extended COFF.
  31 #
  32 # make program = Download the hex file to the device, using avrdude.
  33 #                Please customize the avrdude settings below first!
  34 #
  35 # make dfu = Download the hex file to the device, using dfu-programmer (must
  36 #            have dfu-programmer installed).
  37 #
  38 # make flip = Download the hex file to the device, using Atmel FLIP (must
  39 #             have Atmel FLIP installed).
  40 #
  41 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  42 #               (must have dfu-programmer installed).
  43 #
  44 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  45 #                (must have Atmel FLIP installed).
  46 #
  47 # make doxygen = Generate DoxyGen documentation for the project (must have
  48 #                DoxyGen installed)
  49 #
  50 # make debug = Start either simulavr or avarice as specified for debugging,
  51 #              with avr-gdb or avr-insight as the front end for debugging.
  52 #
  53 # make filename.s = Just compile filename.c into the assembler code only.
  54 #
  55 # make filename.i = Create a preprocessed source file for use in submitting
  56 #                   bug reports to the GCC project.
  57 #
  58 # To rebuild project do "make clean" then "make all".
  59 #----------------------------------------------------------------------------
  60
  61
  62 # MCU name
  63 MCU = at90usb1287
  64
  65
  66 # Target architecture (see library "Board Types" documentation).
  67 ARCH = AVR8
  68
  69
  70 # Target board (see library "Board Types" documentation, NONE for projects not requiring
  71 # LUFA board drivers). If USER is selected, put custom board drivers in a directory called
  72 # "Board" inside the application directory.
  73 BOARD = USBKEY
  74
  75
  76 # Processor frequency.
  77 #     This will define a symbol, F_CPU, in all source code files equal to the
  78 #     processor frequency in Hz. You can then use this symbol in your source code to
  79 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  80 #     automatically to create a 32-bit value in your source code.
  81 #
  82 #     This will be an integer division of F_USB below, as it is sourced by
  83 #     F_USB after it has run through any CPU prescalers. Note that this value
  84 #     does not *change* the processor frequency - it should merely be updated to
  85 #     reflect the processor speed set externally so that the code can use accurate
  86 #     software delays.
  87 F_CPU = 8000000
  88
  89
  90 # Input clock frequency.
  91 #     This will define a symbol, F_USB, in all source code files equal to the
  92 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  93 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  94 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  95 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  96 #     at the end, this will be done automatically to create a 32-bit value in your
  97 #     source code.
  98 #
  99 #     If no clock division is performed on the input clock inside the AVR (via the
 100 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 101 F_USB = $(F_CPU)
 102
 103
 104 # Output format. (can be srec, ihex, binary)
 105 FORMAT = ihex
 106
 107
 108 # Target file name (without extension).
 109 TARGET = AndroidAccessoryHost
 110
 111
 112 # Object files directory
 113 #     To put object files in current directory, use a dot (.), do NOT make
 114 #     this an empty or blank macro!
 115 OBJDIR = .
 116
 117
 118 # Path to the LUFA library
 119 LUFA_PATH = ../../../..
 120
 121
 122 # LUFA library compile-time options and predefined tokens
 123 LUFA_OPTS  = -D USB_HOST_ONLY
 124 LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
 125 LUFA_OPTS += -D HOST_DEVICE_SETTLE_DELAY_MS=0
 126
 127
 128 # Create the LUFA source path variables by including the LUFA root makefile
 129 include $(LUFA_PATH)/LUFA/makefile
 130
 131
 132 # List C source files here. (C dependencies are automatically generated.)
 133 SRC = $(TARGET).c                                                 \
 134           $(LUFA_SRC_USB)                                             \
 135           $(LUFA_SRC_USBCLASS)                                        \
 136           $(LUFA_SRC_SERIAL)
 137
 138
 139 # List C++ source files here. (C dependencies are automatically generated.)
 140 CPPSRC =
 141
 142
 143 # List Assembler source files here.
 144 #     Make them always end in a capital .S.  Files ending in a lowercase .s
 145 #     will not be considered source files but generated files (assembler
 146 #     output from the compiler), and will be deleted upon "make clean"!
 147 #     Even though the DOS/Win* filesystem matches both .s and .S the same,
 148 #     it will preserve the spelling of the filenames, and gcc itself does
 149 #     care about how the name is spelled on its command-line.
 150 ASRC =
 151
 152
 153 # Optimization level, can be [0, 1, 2, 3, s].
 154 #     0 = turn off optimization. s = optimize for size.
 155 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
 156 OPT = s
 157
 158
 159 # Debugging format.
 160 #     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
 161 #     AVR Studio 4.10 requires dwarf-2.
 162 #     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
 163 DEBUG = dwarf-2
 164
 165
 166 # List any extra directories to look for include files here.
 167 #     Each directory must be seperated by a space.
 168 #     Use forward slashes for directory separators.
 169 #     For a directory that has spaces, enclose it in quotes.
 170 EXTRAINCDIRS = $(LUFA_PATH)/
 171
 172
 173 # Compiler flag to set the C Standard level.
 174 #     c89   = "ANSI" C
 175 #     gnu89 = c89 plus GCC extensions
 176 #     c99   = ISO C99 standard (not yet fully implemented)
 177 #     gnu99 = c99 plus GCC extensions
 178 CSTANDARD = -std=c99
 179
 180
 181 # Place -D or -U options here for C sources
 182 CDEFS  = -DF_CPU=$(F_CPU)UL
 183 CDEFS += -DF_USB=$(F_USB)UL
 184 CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
 185 CDEFS += $(LUFA_OPTS)
 186
 187
 188 # Place -D or -U options here for ASM sources
 189 ADEFS  = -DF_CPU=$(F_CPU)
 190 ADEFS += -DF_USB=$(F_USB)UL
 191 ADEFS += -DBOARD=BOARD_$(BOARD)
 192 ADEFS += $(LUFA_OPTS)
 193
 194 # Place -D or -U options here for C++ sources
 195 CPPDEFS  = -DF_CPU=$(F_CPU)UL
 196 CPPDEFS += -DF_USB=$(F_USB)UL
 197 CPPDEFS += -DBOARD=BOARD_$(BOARD)
 198 CPPDEFS += $(LUFA_OPTS)
 199 #CPPDEFS += -D__STDC_LIMIT_MACROS
 200 #CPPDEFS += -D__STDC_CONSTANT_MACROS
 201
 202
 203
 204 #---------------- Compiler Options C ----------------
 205 #  -g*:          generate debugging information
 206 #  -O*:          optimization level
 207 #  -f...:        tuning, see GCC manual and avr-libc documentation
 208 #  -Wall...:     warning level
 209 #  -Wa,...:      tell GCC to pass this to the assembler.
 210 #    -adhlns...: create assembler listing
 211 CFLAGS = -g$(DEBUG)
 212 CFLAGS += $(CDEFS)
 213 CFLAGS += -O$(OPT)
 214 CFLAGS += -funsigned-char
 215 CFLAGS += -funsigned-bitfields
 216 CFLAGS += -ffunction-sections
 217 CFLAGS += -fno-inline-small-functions
 218 CFLAGS += -fpack-struct
 219 CFLAGS += -fshort-enums
 220 CFLAGS += -fno-strict-aliasing
 221 CFLAGS += -Wall
 222 CFLAGS += -Wstrict-prototypes
 223 #CFLAGS += -mshort-calls
 224 #CFLAGS += -fno-unit-at-a-time
 225 #CFLAGS += -Wundef
 226 #CFLAGS += -Wunreachable-code
 227 #CFLAGS += -Wsign-compare
 228 CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 229 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 230 CFLAGS += $(CSTANDARD)
 231
 232
 233 #---------------- Compiler Options C++ ----------------
 234 #  -g*:          generate debugging information
 235 #  -O*:          optimization level
 236 #  -f...:        tuning, see GCC manual and avr-libc documentation
 237 #  -Wall...:     warning level
 238 #  -Wa,...:      tell GCC to pass this to the assembler.
 239 #    -adhlns...: create assembler listing
 240 CPPFLAGS = -g$(DEBUG)
 241 CPPFLAGS += $(CPPDEFS)
 242 CPPFLAGS += -O$(OPT)
 243 CPPFLAGS += -funsigned-char
 244 CPPFLAGS += -funsigned-bitfields
 245 CPPFLAGS += -fpack-struct
 246 CPPFLAGS += -fshort-enums
 247 CPPFLAGS += -fno-exceptions
 248 CPPFLAGS += -Wall
 249 CPPFLAGS += -Wundef
 250 #CPPFLAGS += -mshort-calls
 251 #CPPFLAGS += -fno-unit-at-a-time
 252 #CPPFLAGS += -Wstrict-prototypes
 253 #CPPFLAGS += -Wunreachable-code
 254 #CPPFLAGS += -Wsign-compare
 255 CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 256 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 257 #CPPFLAGS += $(CSTANDARD)
 258
 259
 260 #---------------- Assembler Options ----------------
 261 #  -Wa,...:   tell GCC to pass this to the assembler.
 262 #  -adhlns:   create listing
 263 #  -gstabs:   have the assembler create line number information; note that
 264 #             for use in COFF files, additional information about filenames
 265 #             and function names needs to be present in the assembler source
 266 #             files -- see avr-libc docs [FIXME: not yet described there]
 267 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 268 #       dump that will be displayed for a given single line of source input.
 269 ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 270
 271
 272 #---------------- Library Options ----------------
 273 # Minimalistic printf version
 274 PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
 275
 276 # Floating point printf version (requires MATH_LIB = -lm below)
 277 PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
 278
 279 # If this is left blank, then it will use the Standard printf version.
 280 PRINTF_LIB =
 281 #PRINTF_LIB = $(PRINTF_LIB_MIN)
 282 #PRINTF_LIB = $(PRINTF_LIB_FLOAT)
 283
 284
 285 # Minimalistic scanf version
 286 SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
 287
 288 # Floating point + %[ scanf version (requires MATH_LIB = -lm below)
 289 SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
 290
 291 # If this is left blank, then it will use the Standard scanf version.
 292 SCANF_LIB =
 293 #SCANF_LIB = $(SCANF_LIB_MIN)
 294 #SCANF_LIB = $(SCANF_LIB_FLOAT)
 295
 296
 297 MATH_LIB = -lm
 298
 299
 300 # List any extra directories to look for libraries here.
 301 #     Each directory must be seperated by a space.
 302 #     Use forward slashes for directory separators.
 303 #     For a directory that has spaces, enclose it in quotes.
 304 EXTRALIBDIRS =
 305
 306
 307
 308 #---------------- External Memory Options ----------------
 309
 310 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 311 # used for variables (.data/.bss) and heap (malloc()).
 312 #EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
 313
 314 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 315 # only used for heap (malloc()).
 316 #EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
 317
 318 EXTMEMOPTS =
 319
 320
 321
 322 #---------------- Linker Options ----------------
 323 #  -Wl,...:     tell GCC to pass this to linker.
 324 #    -Map:      create map file
 325 #    --cref:    add cross reference to  map file
 326 LDFLAGS  = -Wl,-Map=$(TARGET).map,--cref
 327 LDFLAGS += -Wl,--relax
 328 LDFLAGS += -Wl,--gc-sections
 329 LDFLAGS += $(EXTMEMOPTS)
 330 LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
 331 LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
 332 #LDFLAGS += -T linker_script.x
 333
 334
 335
 336 #---------------- Programming Options (avrdude) ----------------
 337
 338 # Programming hardware
 339 # Type: avrdude -c ?
 340 # to get a full listing.
 341 #
 342 AVRDUDE_PROGRAMMER = jtagmkII
 343
 344 # com1 = serial port. Use lpt1 to connect to parallel port.
 345 AVRDUDE_PORT = usb
 346
 347 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
 348 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
 349
 350
 351 # Uncomment the following if you want avrdude's erase cycle counter.
 352 # Note that this counter needs to be initialized first using -Yn,
 353 # see avrdude manual.
 354 #AVRDUDE_ERASE_COUNTER = -y
 355
 356 # Uncomment the following if you do /not/ wish a verification to be
 357 # performed after programming the device.
 358 #AVRDUDE_NO_VERIFY = -V
 359
 360 # Increase verbosity level.  Please use this when submitting bug
 361 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
 362 # to submit bug reports.
 363 #AVRDUDE_VERBOSE = -v -v
 364
 365 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
 366 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
 367 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
 368 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 369
 370
 371
 372 #---------------- Debugging Options ----------------
 373
 374 # For simulavr only - target MCU frequency.
 375 DEBUG_MFREQ = $(F_CPU)
 376
 377 # Set the DEBUG_UI to either gdb or insight.
 378 # DEBUG_UI = gdb
 379 DEBUG_UI = insight
 380
 381 # Set the debugging back-end to either avarice, simulavr.
 382 DEBUG_BACKEND = avarice
 383 #DEBUG_BACKEND = simulavr
 384
 385 # GDB Init Filename.
 386 GDBINIT_FILE = __avr_gdbinit
 387
 388 # When using avarice settings for the JTAG
 389 JTAG_DEV = /dev/com1
 390
 391 # Debugging port used to communicate between GDB / avarice / simulavr.
 392 DEBUG_PORT = 4242
 393
 394 # Debugging host used to communicate between GDB / avarice / simulavr, normally
 395 #     just set to localhost unless doing some sort of crazy debugging when
 396 #     avarice is running on a different computer.
 397 DEBUG_HOST = localhost
 398
 399
 400
 401 #============================================================================
 402
 403
 404 # Define programs and commands.
 405 SHELL = sh
 406 CC = avr-gcc
 407 OBJCOPY = avr-objcopy
 408 OBJDUMP = avr-objdump
 409 SIZE = avr-size
 410 AR = avr-ar rcs
 411 NM = avr-nm
 412 AVRDUDE = avrdude
 413 REMOVE = rm -f
 414 REMOVEDIR = rm -rf
 415 COPY = cp
 416 WINSHELL = cmd
 417
 418
 419 # Define Messages
 420 # English
 421 MSG_ERRORS_NONE = Errors: none
 422 MSG_BEGIN = -------- begin --------
 423 MSG_END = --------  end  --------
 424 MSG_SIZE_BEFORE = Size before:
 425 MSG_SIZE_AFTER = Size after:
 426 MSG_COFF = Converting to AVR COFF:
 427 MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
 428 MSG_FLASH = Creating load file for Flash:
 429 MSG_EEPROM = Creating load file for EEPROM:
 430 MSG_EXTENDED_LISTING = Creating Extended Listing:
 431 MSG_SYMBOL_TABLE = Creating Symbol Table:
 432 MSG_LINKING = Linking:
 433 MSG_COMPILING = Compiling C:
 434 MSG_COMPILING_CPP = Compiling C++:
 435 MSG_ASSEMBLING = Assembling:
 436 MSG_CLEANING = Cleaning project:
 437 MSG_CREATING_LIBRARY = Creating library:
 438
 439
 440
 441
 442 # Define all object files.
 443 OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 444
 445 # Define all listing files.
 446 LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 447
 448
 449 # Compiler flags to generate dependency files.
 450 GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
 451
 452
 453 # Combine all necessary flags and optional flags.
 454 # Add target processor to flags.
 455 ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
 456 ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
 457 ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
 458
 459
 460
 461
 462
 463 # Default target.
 464 all: begin gccversion sizebefore build sizeafter end
 465
 466 # Change the build target to build a HEX file or a library.
 467 build: elf hex eep lss sym
 468 #build: lib
 469
 470
 471 elf: $(TARGET).elf
 472 hex: $(TARGET).hex
 473 eep: $(TARGET).eep
 474 lss: $(TARGET).lss
 475 sym: $(TARGET).sym
 476 LIBNAME=lib$(TARGET).a
 477 lib: $(LIBNAME)
 478
 479
 480
 481 # Eye candy.
 482 # AVR Studio 3.x does not check make's exit code but relies on
 483 # the following magic strings to be generated by the compile job.
 484 begin:
 485         @echo
 486         @echo $(MSG_BEGIN)
 487
 488 end:
 489         @echo $(MSG_END)
 490         @echo
 491
 492
 493 # Display size of file.
 494 HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
 495 ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
 496 MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
 497 FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
 498
 499
 500 sizebefore:
 501         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
 502         2>/dev/null; echo; fi
 503
 504 sizeafter:
 505         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
 506         2>/dev/null; echo; fi
 507
 508
 509
 510 # Display compiler version information.
 511 gccversion :
 512         @$(CC) --version
 513
 514
 515 # Program the device.
 516 program: $(TARGET).hex $(TARGET).eep
 517         $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
 518
 519 flip: $(TARGET).hex
 520         batchisp -hardware usb -device $(MCU) -operation erase f
 521         batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
 522         batchisp -hardware usb -device $(MCU) -operation start reset 0
 523
 524 dfu: $(TARGET).hex
 525         dfu-programmer $(MCU) erase
 526         dfu-programmer $(MCU) flash $(TARGET).hex
 527         dfu-programmer $(MCU) reset
 528
 529 flip-ee: $(TARGET).hex $(TARGET).eep
 530         $(COPY) $(TARGET).eep $(TARGET)eep.hex
 531         batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
 532         batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
 533         batchisp -hardware usb -device $(MCU) -operation start reset 0
 534         $(REMOVE) $(TARGET)eep.hex
 535
 536 dfu-ee: $(TARGET).hex $(TARGET).eep
 537         dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
 538         dfu-programmer $(MCU) reset
 539
 540
 541 # Generate avr-gdb config/init file which does the following:
 542 #     define the reset signal, load the target file, connect to target, and set
 543 #     a breakpoint at main().
 544 gdb-config:
 545         @$(REMOVE) $(GDBINIT_FILE)
 546         @echo define reset >> $(GDBINIT_FILE)
 547         @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
 548         @echo end >> $(GDBINIT_FILE)
 549         @echo file $(TARGET).elf >> $(GDBINIT_FILE)
 550         @echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
 551 ifeq ($(DEBUG_BACKEND),simulavr)
 552         @echo load  >> $(GDBINIT_FILE)
 553 endif
 554         @echo break main >> $(GDBINIT_FILE)
 555
 556 debug: gdb-config $(TARGET).elf
 557 ifeq ($(DEBUG_BACKEND), avarice)
 558         @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
 559         @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
 560         $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
 561         @$(WINSHELL) /c pause
 562
 563 else
 564         @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
 565         $(DEBUG_MFREQ) --port $(DEBUG_PORT)
 566 endif
 567         @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
 568
 569
 570
 571
 572 # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
 573 COFFCONVERT = $(OBJCOPY) --debugging
 574 COFFCONVERT += --change-section-address .data-0x800000
 575 COFFCONVERT += --change-section-address .bss-0x800000
 576 COFFCONVERT += --change-section-address .noinit-0x800000
 577 COFFCONVERT += --change-section-address .eeprom-0x810000
 578
 579
 580
 581 coff: $(TARGET).elf
 582         @echo
 583         @echo $(MSG_COFF) $(TARGET).cof
 584         $(COFFCONVERT) -O coff-avr $< $(TARGET).cof
 585
 586
 587 extcoff: $(TARGET).elf
 588         @echo
 589         @echo $(MSG_EXTENDED_COFF) $(TARGET).cof
 590         $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
 591
 592
 593
 594 # Create final output files (.hex, .eep) from ELF output file.
 595 %.hex: %.elf
 596         @echo
 597         @echo $(MSG_FLASH) $@
 598         $(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock $< $@
 599
 600 %.eep: %.elf
 601         @echo
 602         @echo $(MSG_EEPROM) $@
 603         -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
 604         --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
 605
 606 # Create extended listing file from ELF output file.
 607 %.lss: %.elf
 608         @echo
 609         @echo $(MSG_EXTENDED_LISTING) $@
 610         $(OBJDUMP) -h -S -z $< > $@
 611
 612 # Create a symbol table from ELF output file.
 613 %.sym: %.elf
 614         @echo
 615         @echo $(MSG_SYMBOL_TABLE) $@
 616         $(NM) -n $< > $@
 617
 618
 619
 620 # Create library from object files.
 621 .SECONDARY : $(TARGET).a
 622 .PRECIOUS : $(OBJ)
 623 %.a: $(OBJ)
 624         @echo
 625         @echo $(MSG_CREATING_LIBRARY) $@
 626         $(AR) $@ $(OBJ)
 627
 628
 629 # Link: create ELF output file from object files.
 630 .SECONDARY : $(TARGET).elf
 631 .PRECIOUS : $(OBJ)
 632 %.elf: $(OBJ)
 633         @echo
 634         @echo $(MSG_LINKING) $@
 635         $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
 636
 637
 638 # Compile: create object files from C source files.
 639 $(OBJDIR)/%.o : %.c
 640         @echo
 641         @echo $(MSG_COMPILING) $<
 642         $(CC) -c $(ALL_CFLAGS) $< -o $@
 643
 644
 645 # Compile: create object files from C++ source files.
 646 $(OBJDIR)/%.o : %.cpp
 647         @echo
 648         @echo $(MSG_COMPILING_CPP) $<
 649         $(CC) -c $(ALL_CPPFLAGS) $< -o $@
 650
 651
 652 # Compile: create assembler files from C source files.
 653 %.s : %.c
 654         $(CC) -S $(ALL_CFLAGS) $< -o $@
 655
 656
 657 # Compile: create assembler files from C++ source files.
 658 %.s : %.cpp
 659         $(CC) -S $(ALL_CPPFLAGS) $< -o $@
 660
 661
 662 # Assemble: create object files from assembler source files.
 663 $(OBJDIR)/%.o : %.S
 664         @echo
 665         @echo $(MSG_ASSEMBLING) $<
 666         $(CC) -c $(ALL_ASFLAGS) $< -o $@
 667
 668
 669 # Create preprocessed source for use in sending a bug report.
 670 %.i : %.c
 671         $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
 672
 673
 674 # Target: clean project.
 675 clean: begin clean_list end
 676
 677 clean_list :
 678         @echo
 679         @echo $(MSG_CLEANING)
 680         $(REMOVE) $(TARGET).hex
 681         $(REMOVE) $(TARGET).eep
 682         $(REMOVE) $(TARGET).cof
 683         $(REMOVE) $(TARGET).elf
 684         $(REMOVE) $(TARGET).map
 685         $(REMOVE) $(TARGET).sym
 686         $(REMOVE) $(TARGET).lss
 687         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 688         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 689         $(REMOVE) $(SRC:.c=.s)
 690         $(REMOVE) $(SRC:.c=.d)
 691         $(REMOVE) $(SRC:.c=.i)
 692         $(REMOVEDIR) .dep
 693
 694 doxygen:
 695         @echo Generating Project Documentation \($(TARGET)\)...
 696         @doxygen Doxygen.conf
 697         @echo Documentation Generation Complete.
 698
 699 clean_doxygen:
 700         rm -rf Documentation
 701
 702 checksource:
 703         @for f in $(SRC) $(CPPSRC) $(ASRC); do \
 704                 if [ -f $$f ]; then \
 705                         echo "Found Source File: $$f" ; \
 706                 else \
 707                         echo "Source File Not Found: $$f" ; \
 708                 fi; done
 709
 710
 711 # Create object files directory
 712 $(shell mkdir $(OBJDIR) 2>/dev/null)
 713
 714
 715 # Include the dependency files.
 716 -include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
 717
 718
 719 # Listing of phony targets.
 720 .PHONY : all begin finish end sizebefore sizeafter gccversion \
 721 build elf hex eep lss sym coff extcoff doxygen clean          \
 722 clean_list clean_doxygen program dfu flip flip-ee dfu-ee      \
 723 debug gdb-config checksource