Demos/Device/LowLevel/GenericHID/makefile

   1 # Hey Emacs, this is a -*- makefile -*-
   2 #----------------------------------------------------------------------------
   3 # WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
   4 #  >> Modified for use with the LUFA project. <<
   5 #
   6 # Released to the Public Domain
   7 #
   8 # Additional material for this makefile was written by:
   9 # Peter Fleury
  10 # Tim Henigan
  11 # Colin O'Flynn
  12 # Reiner Patommel
  13 # Markus Pfaff
  14 # Sander Pool
  15 # Frederik Rouleau
  16 # Carlos Lamas
  17 # Dean Camera
  18 # Opendous Inc.
  19 # Denver Gingerich
  20 #
  21 #----------------------------------------------------------------------------
  22 # On command line:
  23 #
  24 # make all = Make software.
  25 #
  26 # make clean = Clean out built project files.
  27 #
  28 # make coff = Convert ELF to AVR COFF.
  29 #
  30 # make extcoff = Convert ELF to AVR Extended COFF.
  31 #
  32 # make program = Download the hex file to the device, using avrdude.
  33 #                Please customize the avrdude settings below first!
  34 #
  35 # make dfu = Download the hex file to the device, using dfu-programmer (must
  36 #            have dfu-programmer installed).
  37 #
  38 # make flip = Download the hex file to the device, using Atmel FLIP (must
  39 #             have Atmel FLIP installed).
  40 #
  41 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  42 #               (must have dfu-programmer installed).
  43 #
  44 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  45 #                (must have Atmel FLIP installed).
  46 #
  47 # make doxygen = Generate DoxyGen documentation for the project (must have
  48 #                DoxyGen installed)
  49 #
  50 # make debug = Start either simulavr or avarice as specified for debugging,
  51 #              with avr-gdb or avr-insight as the front end for debugging.
  52 #
  53 # make filename.s = Just compile filename.c into the assembler code only.
  54 #
  55 # make filename.i = Create a preprocessed source file for use in submitting
  56 #                   bug reports to the GCC project.
  57 #
  58 # To rebuild project do "make clean" then "make all".
  59 #----------------------------------------------------------------------------
  60
  61
  62 # MCU name
  63 MCU = at90usb1287
  64
  65
  66 # Target board (see library "Board Types" documentation, USER or blank for projects not requiring
  67 # LUFA board drivers). If USER is selected, put custom board drivers in a directory called
  68 # "Board" inside the application directory.
  69 BOARD  = USBKEY
  70
  71
  72 # Processor frequency.
  73 #     This will define a symbol, F_CPU, in all source code files equal to the
  74 #     processor frequency. You can then use this symbol in your source code to
  75 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  76 #     automatically to create a 32-bit value in your source code.
  77 #     Typical values are:
  78 #         F_CPU =  1000000
  79 #         F_CPU =  1843200
  80 #         F_CPU =  2000000
  81 #         F_CPU =  3686400
  82 #         F_CPU =  4000000
  83 #         F_CPU =  7372800
  84 #         F_CPU =  8000000
  85 #         F_CPU = 11059200
  86 #         F_CPU = 14745600
  87 #         F_CPU = 16000000
  88 #         F_CPU = 18432000
  89 #         F_CPU = 20000000
  90 F_CPU = 8000000
  91
  92
  93 # Input clock frequency.
  94 #     This will define a symbol, F_CLOCK, in all source code files equal to the
  95 #     input clock frequency (before any prescaling is performed). This value may
  96 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  97 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  98 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  99 #     at the end, this will be done automatically to create a 32-bit value in your
 100 #     source code.
 101 #
 102 #     If no clock division is performed on the input clock inside the AVR (via the
 103 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 104 F_CLOCK = 8000000
 105
 106
 107 # Output format. (can be srec, ihex, binary)
 108 FORMAT = ihex
 109
 110
 111 # Target file name (without extension).
 112 TARGET = GenericHID
 113
 114
 115 # Object files directory
 116 #     To put object files in current directory, use a dot (.), do NOT make
 117 #     this an empty or blank macro!
 118 OBJDIR = .
 119
 120
 121 # Path to the LUFA library
 122 LUFA_PATH = ../../../..
 123
 124
 125 # List C source files here. (C dependencies are automatically generated.)
 126 SRC = $(TARGET).c                                                 \
 127           Descriptors.c                                               \
 128           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/DevChapter9.c        \
 129           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Endpoint.c           \
 130           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Host.c               \
 131           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/HostChapter9.c       \
 132           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/LowLevel.c           \
 133           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Pipe.c               \
 134           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/Events.c            \
 135           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBInterrupt.c      \
 136           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBTask.c           \
 137           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/ConfigDescriptor.c  \
 138
 139
 140 # List C++ source files here. (C dependencies are automatically generated.)
 141 CPPSRC =
 142
 143
 144 # List Assembler source files here.
 145 #     Make them always end in a capital .S.  Files ending in a lowercase .s
 146 #     will not be considered source files but generated files (assembler
 147 #     output from the compiler), and will be deleted upon "make clean"!
 148 #     Even though the DOS/Win* filesystem matches both .s and .S the same,
 149 #     it will preserve the spelling of the filenames, and gcc itself does
 150 #     care about how the name is spelled on its command-line.
 151 ASRC =
 152
 153
 154 # Optimization level, can be [0, 1, 2, 3, s].
 155 #     0 = turn off optimization. s = optimize for size.
 156 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
 157 OPT = s
 158
 159
 160 # Debugging format.
 161 #     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
 162 #     AVR Studio 4.10 requires dwarf-2.
 163 #     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
 164 DEBUG = dwarf-2
 165
 166
 167 # List any extra directories to look for include files here.
 168 #     Each directory must be seperated by a space.
 169 #     Use forward slashes for directory separators.
 170 #     For a directory that has spaces, enclose it in quotes.
 171 EXTRAINCDIRS = $(LUFA_PATH)/
 172
 173
 174 # Compiler flag to set the C Standard level.
 175 #     c89   = "ANSI" C
 176 #     gnu89 = c89 plus GCC extensions
 177 #     c99   = ISO C99 standard (not yet fully implemented)
 178 #     gnu99 = c99 plus GCC extensions
 179 CSTANDARD = -std=gnu99
 180
 181
 182 # Place -D or -U options here for C sources
 183 CDEFS  = -DF_CPU=$(F_CPU)UL -DF_CLOCK=$(F_CLOCK)UL -DBOARD=BOARD_$(BOARD)
 184 CDEFS += -DUSE_NONSTANDARD_DESCRIPTOR_NAMES -DNO_STREAM_CALLBACKS -DUSB_DEVICE_ONLY
 185 CDEFS += -DFIXED_CONTROL_ENDPOINT_SIZE=8 -DUSE_SINGLE_DEVICE_CONFIGURATION
 186 CDEFS += -DUSE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
 187
 188 # Place -D or -U options here for ASM sources
 189 ADEFS = -DF_CPU=$(F_CPU)
 190
 191
 192 # Place -D or -U options here for C++ sources
 193 CPPDEFS = -DF_CPU=$(F_CPU)UL
 194 #CPPDEFS += -D__STDC_LIMIT_MACROS
 195 #CPPDEFS += -D__STDC_CONSTANT_MACROS
 196
 197
 198
 199 #---------------- Compiler Options C ----------------
 200 #  -g*:          generate debugging information
 201 #  -O*:          optimization level
 202 #  -f...:        tuning, see GCC manual and avr-libc documentation
 203 #  -Wall...:     warning level
 204 #  -Wa,...:      tell GCC to pass this to the assembler.
 205 #    -adhlns...: create assembler listing
 206 CFLAGS = -g$(DEBUG)
 207 CFLAGS += $(CDEFS)
 208 CFLAGS += -O$(OPT)
 209 CFLAGS += -funsigned-char
 210 CFLAGS += -funsigned-bitfields
 211 CFLAGS += -ffunction-sections
 212 CFLAGS += -fpack-struct
 213 CFLAGS += -fshort-enums
 214 CFLAGS += -finline-limit=20
 215 CFLAGS += -Wall
 216 CFLAGS += -Wstrict-prototypes
 217 CFLAGS += -Wundef
 218 #CFLAGS += -fno-unit-at-a-time
 219 #CFLAGS += -Wunreachable-code
 220 #CFLAGS += -Wsign-compare
 221 CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 222 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 223 CFLAGS += $(CSTANDARD)
 224
 225
 226 #---------------- Compiler Options C++ ----------------
 227 #  -g*:          generate debugging information
 228 #  -O*:          optimization level
 229 #  -f...:        tuning, see GCC manual and avr-libc documentation
 230 #  -Wall...:     warning level
 231 #  -Wa,...:      tell GCC to pass this to the assembler.
 232 #    -adhlns...: create assembler listing
 233 CPPFLAGS = -g$(DEBUG)
 234 CPPFLAGS += $(CPPDEFS)
 235 CPPFLAGS += -O$(OPT)
 236 CPPFLAGS += -funsigned-char
 237 CPPFLAGS += -funsigned-bitfields
 238 CPPFLAGS += -fpack-struct
 239 CPPFLAGS += -fshort-enums
 240 CPPFLAGS += -fno-exceptions
 241 CPPFLAGS += -Wall
 242 CFLAGS += -Wundef
 243 #CPPFLAGS += -mshort-calls
 244 #CPPFLAGS += -fno-unit-at-a-time
 245 #CPPFLAGS += -Wstrict-prototypes
 246 #CPPFLAGS += -Wunreachable-code
 247 #CPPFLAGS += -Wsign-compare
 248 CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 249 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 250 #CPPFLAGS += $(CSTANDARD)
 251
 252
 253 #---------------- Assembler Options ----------------
 254 #  -Wa,...:   tell GCC to pass this to the assembler.
 255 #  -adhlns:   create listing
 256 #  -gstabs:   have the assembler create line number information; note that
 257 #             for use in COFF files, additional information about filenames
 258 #             and function names needs to be present in the assembler source
 259 #             files -- see avr-libc docs [FIXME: not yet described there]
 260 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 261 #       dump that will be displayed for a given single line of source input.
 262 ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 263
 264
 265 #---------------- Library Options ----------------
 266 # Minimalistic printf version
 267 PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
 268
 269 # Floating point printf version (requires MATH_LIB = -lm below)
 270 PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
 271
 272 # If this is left blank, then it will use the Standard printf version.
 273 PRINTF_LIB =
 274 #PRINTF_LIB = $(PRINTF_LIB_MIN)
 275 #PRINTF_LIB = $(PRINTF_LIB_FLOAT)
 276
 277
 278 # Minimalistic scanf version
 279 SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
 280
 281 # Floating point + %[ scanf version (requires MATH_LIB = -lm below)
 282 SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
 283
 284 # If this is left blank, then it will use the Standard scanf version.
 285 SCANF_LIB =
 286 #SCANF_LIB = $(SCANF_LIB_MIN)
 287 #SCANF_LIB = $(SCANF_LIB_FLOAT)
 288
 289
 290 MATH_LIB = -lm
 291
 292
 293 # List any extra directories to look for libraries here.
 294 #     Each directory must be seperated by a space.
 295 #     Use forward slashes for directory separators.
 296 #     For a directory that has spaces, enclose it in quotes.
 297 EXTRALIBDIRS =
 298
 299
 300
 301 #---------------- External Memory Options ----------------
 302
 303 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 304 # used for variables (.data/.bss) and heap (malloc()).
 305 #EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
 306
 307 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 308 # only used for heap (malloc()).
 309 #EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
 310
 311 EXTMEMOPTS =
 312
 313
 314
 315 #---------------- Linker Options ----------------
 316 #  -Wl,...:     tell GCC to pass this to linker.
 317 #    -Map:      create map file
 318 #    --cref:    add cross reference to  map file
 319 LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
 320 LDFLAGS += -Wl,--relax
 321 LDFLAGS += -Wl,--gc-sections
 322 LDFLAGS += $(EXTMEMOPTS)
 323 LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
 324 LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
 325 #LDFLAGS += -T linker_script.x
 326
 327
 328
 329 #---------------- Programming Options (avrdude) ----------------
 330
 331 # Programming hardware: alf avr910 avrisp bascom bsd
 332 # dt006 pavr picoweb pony-stk200 sp12 stk200 stk500
 333 #
 334 # Type: avrdude -c ?
 335 # to get a full listing.
 336 #
 337 AVRDUDE_PROGRAMMER = jtagmkII
 338
 339 # com1 = serial port. Use lpt1 to connect to parallel port.
 340 AVRDUDE_PORT = usb
 341
 342 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
 343 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
 344
 345
 346 # Uncomment the following if you want avrdude's erase cycle counter.
 347 # Note that this counter needs to be initialized first using -Yn,
 348 # see avrdude manual.
 349 #AVRDUDE_ERASE_COUNTER = -y
 350
 351 # Uncomment the following if you do /not/ wish a verification to be
 352 # performed after programming the device.
 353 #AVRDUDE_NO_VERIFY = -V
 354
 355 # Increase verbosity level.  Please use this when submitting bug
 356 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
 357 # to submit bug reports.
 358 #AVRDUDE_VERBOSE = -v -v
 359
 360 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
 361 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
 362 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
 363 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 364
 365
 366
 367 #---------------- Debugging Options ----------------
 368
 369 # For simulavr only - target MCU frequency.
 370 DEBUG_MFREQ = $(F_CPU)
 371
 372 # Set the DEBUG_UI to either gdb or insight.
 373 # DEBUG_UI = gdb
 374 DEBUG_UI = insight
 375
 376 # Set the debugging back-end to either avarice, simulavr.
 377 DEBUG_BACKEND = avarice
 378 #DEBUG_BACKEND = simulavr
 379
 380 # GDB Init Filename.
 381 GDBINIT_FILE = __avr_gdbinit
 382
 383 # When using avarice settings for the JTAG
 384 JTAG_DEV = /dev/com1
 385
 386 # Debugging port used to communicate between GDB / avarice / simulavr.
 387 DEBUG_PORT = 4242
 388
 389 # Debugging host used to communicate between GDB / avarice / simulavr, normally
 390 #     just set to localhost unless doing some sort of crazy debugging when
 391 #     avarice is running on a different computer.
 392 DEBUG_HOST = localhost
 393
 394
 395
 396 #============================================================================
 397
 398
 399 # Define programs and commands.
 400 SHELL = sh
 401 CC = avr-gcc
 402 OBJCOPY = avr-objcopy
 403 OBJDUMP = avr-objdump
 404 SIZE = avr-size
 405 AR = avr-ar rcs
 406 NM = avr-nm
 407 AVRDUDE = avrdude
 408 REMOVE = rm -f
 409 REMOVEDIR = rm -rf
 410 COPY = cp
 411 WINSHELL = cmd
 412
 413 # Define Messages
 414 # English
 415 MSG_ERRORS_NONE = Errors: none
 416 MSG_BEGIN = -------- begin --------
 417 MSG_END = --------  end  --------
 418 MSG_SIZE_BEFORE = Size before:
 419 MSG_SIZE_AFTER = Size after:
 420 MSG_COFF = Converting to AVR COFF:
 421 MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
 422 MSG_FLASH = Creating load file for Flash:
 423 MSG_EEPROM = Creating load file for EEPROM:
 424 MSG_EXTENDED_LISTING = Creating Extended Listing:
 425 MSG_SYMBOL_TABLE = Creating Symbol Table:
 426 MSG_LINKING = Linking:
 427 MSG_COMPILING = Compiling C:
 428 MSG_COMPILING_CPP = Compiling C++:
 429 MSG_ASSEMBLING = Assembling:
 430 MSG_CLEANING = Cleaning project:
 431 MSG_CREATING_LIBRARY = Creating library:
 432
 433
 434
 435
 436 # Define all object files.
 437 OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 438
 439 # Define all listing files.
 440 LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 441
 442
 443 # Compiler flags to generate dependency files.
 444 GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
 445
 446
 447 # Combine all necessary flags and optional flags.
 448 # Add target processor to flags.
 449 ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
 450 ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
 451 ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
 452
 453
 454
 455
 456
 457 # Default target.
 458 all: begin gccversion sizebefore build checkhooks checklibmode checkboard sizeafter end
 459
 460 # Change the build target to build a HEX file or a library.
 461 build: elf hex eep lss sym
 462 #build: lib
 463
 464
 465 elf: $(TARGET).elf
 466 hex: $(TARGET).hex
 467 eep: $(TARGET).eep
 468 lss: $(TARGET).lss
 469 sym: $(TARGET).sym
 470 LIBNAME=lib$(TARGET).a
 471 lib: $(LIBNAME)
 472
 473
 474
 475 # Eye candy.
 476 # AVR Studio 3.x does not check make's exit code but relies on
 477 # the following magic strings to be generated by the compile job.
 478 begin:
 479         @echo
 480         @echo $(MSG_BEGIN)
 481
 482 end:
 483         @echo $(MSG_END)
 484         @echo
 485
 486
 487 # Display size of file.
 488 HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
 489 ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
 490 MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
 491 FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
 492
 493 sizebefore:
 494         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
 495         2>/dev/null; echo; fi
 496
 497 sizeafter:
 498         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
 499         2>/dev/null; echo; fi
 500
 501 checkhooks: build
 502         @echo
 503         @echo ------- Unhooked LUFA Events -------
 504         @$(shell) (grep -s '^EVENT_.*LUFA/.*\\.o' $(TARGET).map | \
 505                    cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \
 506                            echo "(None)"
 507         @echo ------------------------------------
 508
 509 checklibmode:
 510         @echo
 511         @echo ----------- Library Mode -----------
 512         @$(shell) ($(CC) $(ALL_CFLAGS) -E -dM - < /dev/null \
 513                   | grep 'USB_\(DEVICE\|HOST\)_ONLY' | cut -d' ' -f2 | grep ".*") \
 514                   || echo "No specific mode (both device and host mode allowable)."
 515         @echo ------------------------------------
 516
 517 checkboard:
 518         @echo
 519         @echo ---------- Selected Board ----------
 520         @echo Selected board model is $(BOARD).
 521         @echo ------------------------------------
 522
 523 # Display compiler version information.
 524 gccversion :
 525         @$(CC) --version
 526
 527
 528
 529 # Program the device.
 530 program: $(TARGET).hex $(TARGET).eep
 531         $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
 532
 533 flip: $(TARGET).hex
 534         batchisp -hardware usb -device $(MCU) -operation erase f
 535         batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
 536         batchisp -hardware usb -device $(MCU) -operation start reset 0
 537
 538 dfu: $(TARGET).hex
 539         dfu-programmer $(MCU) erase
 540         dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex
 541         dfu-programmer $(MCU) reset
 542
 543 flip-ee: $(TARGET).hex $(TARGET).eep
 544         copy $(TARGET).eep $(TARGET)eep.hex
 545         batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
 546         batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
 547         batchisp -hardware usb -device $(MCU) -operation start reset 0
 548
 549 dfu-ee: $(TARGET).hex $(TARGET).eep
 550         dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
 551         dfu-programmer $(MCU) reset
 552
 553
 554 # Generate avr-gdb config/init file which does the following:
 555 #     define the reset signal, load the target file, connect to target, and set
 556 #     a breakpoint at main().
 557 gdb-config:
 558         @$(REMOVE) $(GDBINIT_FILE)
 559         @echo define reset >> $(GDBINIT_FILE)
 560         @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
 561         @echo end >> $(GDBINIT_FILE)
 562         @echo file $(TARGET).elf >> $(GDBINIT_FILE)
 563         @echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
 564 ifeq ($(DEBUG_BACKEND),simulavr)
 565         @echo load  >> $(GDBINIT_FILE)
 566 endif
 567         @echo break main >> $(GDBINIT_FILE)
 568
 569 debug: gdb-config $(TARGET).elf
 570 ifeq ($(DEBUG_BACKEND), avarice)
 571         @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
 572         @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
 573         $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
 574         @$(WINSHELL) /c pause
 575
 576 else
 577         @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
 578         $(DEBUG_MFREQ) --port $(DEBUG_PORT)
 579 endif
 580         @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
 581
 582
 583
 584
 585 # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
 586 COFFCONVERT = $(OBJCOPY) --debugging
 587 COFFCONVERT += --change-section-address .data-0x800000
 588 COFFCONVERT += --change-section-address .bss-0x800000
 589 COFFCONVERT += --change-section-address .noinit-0x800000
 590 COFFCONVERT += --change-section-address .eeprom-0x810000
 591
 592
 593
 594 coff: $(TARGET).elf
 595         @echo
 596         @echo $(MSG_COFF) $(TARGET).cof
 597         $(COFFCONVERT) -O coff-avr $< $(TARGET).cof
 598
 599
 600 extcoff: $(TARGET).elf
 601         @echo
 602         @echo $(MSG_EXTENDED_COFF) $(TARGET).cof
 603         $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
 604
 605
 606
 607 # Create final output files (.hex, .eep) from ELF output file.
 608 %.hex: %.elf
 609         @echo
 610         @echo $(MSG_FLASH) $@
 611         $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
 612
 613 %.eep: %.elf
 614         @echo
 615         @echo $(MSG_EEPROM) $@
 616         -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
 617         --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
 618
 619 # Create extended listing file from ELF output file.
 620 %.lss: %.elf
 621         @echo
 622         @echo $(MSG_EXTENDED_LISTING) $@
 623         $(OBJDUMP) -h -z -S $< > $@
 624
 625 # Create a symbol table from ELF output file.
 626 %.sym: %.elf
 627         @echo
 628         @echo $(MSG_SYMBOL_TABLE) $@
 629         $(NM) -n $< > $@
 630
 631
 632
 633 # Create library from object files.
 634 .SECONDARY : $(TARGET).a
 635 .PRECIOUS : $(OBJ)
 636 %.a: $(OBJ)
 637         @echo
 638         @echo $(MSG_CREATING_LIBRARY) $@
 639         $(AR) $@ $(OBJ)
 640
 641
 642 # Link: create ELF output file from object files.
 643 .SECONDARY : $(TARGET).elf
 644 .PRECIOUS : $(OBJ)
 645 %.elf: $(OBJ)
 646         @echo
 647         @echo $(MSG_LINKING) $@
 648         $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
 649
 650
 651 # Compile: create object files from C source files.
 652 $(OBJDIR)/%.o : %.c
 653         @echo
 654         @echo $(MSG_COMPILING) $<
 655         $(CC) -c $(ALL_CFLAGS) $< -o $@
 656
 657
 658 # Compile: create object files from C++ source files.
 659 $(OBJDIR)/%.o : %.cpp
 660         @echo
 661         @echo $(MSG_COMPILING_CPP) $<
 662         $(CC) -c $(ALL_CPPFLAGS) $< -o $@
 663
 664
 665 # Compile: create assembler files from C source files.
 666 %.s : %.c
 667         $(CC) -S $(ALL_CFLAGS) $< -o $@
 668
 669
 670 # Compile: create assembler files from C++ source files.
 671 %.s : %.cpp
 672         $(CC) -S $(ALL_CPPFLAGS) $< -o $@
 673
 674
 675 # Assemble: create object files from assembler source files.
 676 $(OBJDIR)/%.o : %.S
 677         @echo
 678         @echo $(MSG_ASSEMBLING) $<
 679         $(CC) -c $(ALL_ASFLAGS) $< -o $@
 680
 681
 682 # Create preprocessed source for use in sending a bug report.
 683 %.i : %.c
 684         $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
 685
 686
 687 # Target: clean project.
 688 clean: begin clean_list clean_binary end
 689
 690 clean_binary:
 691         $(REMOVE) $(TARGET).hex
 692
 693 clean_list:
 694         @echo $(MSG_CLEANING)
 695         $(REMOVE) $(TARGET).eep
 696         $(REMOVE) $(TARGET)eep.hex
 697         $(REMOVE) $(TARGET).cof
 698         $(REMOVE) $(TARGET).elf
 699         $(REMOVE) $(TARGET).map
 700         $(REMOVE) $(TARGET).sym
 701         $(REMOVE) $(TARGET).lss
 702         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
 703         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
 704         $(REMOVE) $(SRC:.c=.s)
 705         $(REMOVE) $(SRC:.c=.d)
 706         $(REMOVE) $(SRC:.c=.i)
 707         $(REMOVEDIR) .dep
 708
 709
 710 doxygen:
 711         @echo Generating Project Documentation...
 712         @doxygen Doxygen.conf
 713         @echo Documentation Generation Complete.
 714
 715 clean_doxygen:
 716         rm -rf Documentation
 717
 718 # Create object files directory
 719 $(shell mkdir $(OBJDIR) 2>/dev/null)
 720
 721
 722 # Include the dependency files.
 723 -include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
 724
 725
 726 # Listing of phony targets.
 727 .PHONY : all checkhooks checklibmode checkboard   \
 728 begin finish end sizebefore sizeafter gccversion  \
 729 build elf hex eep lss sym coff extcoff clean      \
 730 clean_list clean_binary program debug gdb-config  \
 731 doxygen dfu flip flip-ee dfu-ee