Demos/Device/USBtoSerial/makefile

   1 # Hey Emacs, this is a -*- makefile -*-
   2 #----------------------------------------------------------------------------
   3 # WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
   4 #  >> Modified for use with the LUFA project. <<
   5 #
   6 # Released to the Public Domain
   7 #
   8 # Additional material for this makefile was written by:
   9 # Peter Fleury
  10 # Tim Henigan
  11 # Colin O'Flynn
  12 # Reiner Patommel
  13 # Markus Pfaff
  14 # Sander Pool
  15 # Frederik Rouleau
  16 # Carlos Lamas
  17 # Dean Camera
  18 # Opendous Inc.
  19 # Denver Gingerich
  20 #
  21 #----------------------------------------------------------------------------
  22 # On command line:
  23 #
  24 # make all = Make software.
  25 #
  26 # make clean = Clean out built project files.
  27 #
  28 # make coff = Convert ELF to AVR COFF.
  29 #
  30 # make extcoff = Convert ELF to AVR Extended COFF.
  31 #
  32 # make program = Download the hex file to the device, using avrdude.
  33 #                Please customize the avrdude settings below first!
  34 #
  35 # make dfu = Download the hex file to the device, using dfu-programmer (must
  36 #            have dfu-programmer installed).
  37 #
  38 # make flip = Download the hex file to the device, using Atmel FLIP (must
  39 #             have Atmel FLIP installed).
  40 #
  41 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  42 #               (must have dfu-programmer installed).
  43 #
  44 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  45 #                (must have Atmel FLIP installed).
  46 #
  47 # make doxygen = Generate DoxyGen documentation for the project (must have
  48 #                DoxyGen installed)
  49 #
  50 # make debug = Start either simulavr or avarice as specified for debugging,
  51 #              with avr-gdb or avr-insight as the front end for debugging.
  52 #
  53 # make filename.s = Just compile filename.c into the assembler code only.
  54 #
  55 # make filename.i = Create a preprocessed source file for use in submitting
  56 #                   bug reports to the GCC project.
  57 #
  58 # To rebuild project do "make clean" then "make all".
  59 #----------------------------------------------------------------------------
  60
  61
  62 # MCU name
  63 MCU = at90usb1287
  64
  65
  66 # Target board (see library BoardTypes.h documentation, USER or blank for projects not requiring
  67 # LUFA board drivers). If USER is selected, put custom board drivers in a directory called
  68 # "Board" inside the application directory.
  69 BOARD  = USBKEY
  70
  71
  72 # Processor frequency.
  73 #     This will define a symbol, F_CPU, in all source code files equal to the
  74 #     processor frequency. You can then use this symbol in your source code to
  75 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  76 #     automatically to create a 32-bit value in your source code.
  77 #     Typical values are:
  78 #         F_CPU =  1000000
  79 #         F_CPU =  1843200
  80 #         F_CPU =  2000000
  81 #         F_CPU =  3686400
  82 #         F_CPU =  4000000
  83 #         F_CPU =  7372800
  84 #         F_CPU =  8000000
  85 #         F_CPU = 11059200
  86 #         F_CPU = 14745600
  87 #         F_CPU = 16000000
  88 #         F_CPU = 18432000
  89 #         F_CPU = 20000000
  90 F_CPU = 8000000
  91
  92
  93 # Input clock frequency.
  94 #     This will define a symbol, F_CLOCK, in all source code files equal to the
  95 #     input clock frequency (before any prescaling is performed). This value may
  96 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  97 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  98 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  99 #     at the end, this will be done automatically to create a 32-bit value in your
 100 #     source code.
 101 #
 102 #     If no clock division is performed on the input clock inside the AVR (via the
 103 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 104 F_CLOCK = 8000000
 105
 106
 107 # Output format. (can be srec, ihex, binary)
 108 FORMAT = ihex
 109
 110
 111 # Target file name (without extension).
 112 TARGET = USBtoSerial
 113
 114
 115 # Object files directory
 116 #     To put object files in current directory, use a dot (.), do NOT make
 117 #     this an empty or blank macro!
 118 OBJDIR = .
 119
 120
 121 # Path to the LUFA library
 122 LUFA_PATH = ../../..
 123
 124
 125 # List C source files here. (C dependencies are automatically generated.)
 126 SRC = $(TARGET).c                                                 \
 127           Descriptors.c                                               \
 128           RingBuff.c                                                  \
 129           $(LUFA_PATH)/LUFA/Scheduler/Scheduler.c                     \
 130           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/DevChapter9.c        \
 131           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Endpoint.c           \
 132           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Host.c               \
 133           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/HostChapter9.c       \
 134           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/LowLevel.c           \
 135           $(LUFA_PATH)/LUFA/Drivers/USB/LowLevel/Pipe.c               \
 136           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/Events.c            \
 137           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/StdDescriptors.c    \
 138           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBInterrupt.c      \
 139           $(LUFA_PATH)/LUFA/Drivers/USB/HighLevel/USBTask.c           \
 140           $(LUFA_PATH)/LUFA/Drivers/USB/Class/ConfigDescriptor.c      \
 141           $(LUFA_PATH)/LUFA/Drivers/USB/Class/HIDParser.c             \
 142
 143
 144 # List C++ source files here. (C dependencies are automatically generated.)
 145 CPPSRC =
 146
 147
 148 # List Assembler source files here.
 149 #     Make them always end in a capital .S.  Files ending in a lowercase .s
 150 #     will not be considered source files but generated files (assembler
 151 #     output from the compiler), and will be deleted upon "make clean"!
 152 #     Even though the DOS/Win* filesystem matches both .s and .S the same,
 153 #     it will preserve the spelling of the filenames, and gcc itself does
 154 #     care about how the name is spelled on its command-line.
 155 ASRC =
 156
 157
 158 # Optimization level, can be [0, 1, 2, 3, s].
 159 #     0 = turn off optimization. s = optimize for size.
 160 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
 161 OPT = s
 162
 163
 164 # Debugging format.
 165 #     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
 166 #     AVR Studio 4.10 requires dwarf-2.
 167 #     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
 168 DEBUG = dwarf-2
 169
 170
 171 # List any extra directories to look for include files here.
 172 #     Each directory must be seperated by a space.
 173 #     Use forward slashes for directory separators.
 174 #     For a directory that has spaces, enclose it in quotes.
 175 EXTRAINCDIRS = $(LUFA_PATH)/
 176
 177
 178 # Compiler flag to set the C Standard level.
 179 #     c89   = "ANSI" C
 180 #     gnu89 = c89 plus GCC extensions
 181 #     c99   = ISO C99 standard (not yet fully implemented)
 182 #     gnu99 = c99 plus GCC extensions
 183 CSTANDARD = -std=gnu99
 184
 185
 186 # Place -D or -U options here for C sources
 187 CDEFS  = -DF_CPU=$(F_CPU)UL -DF_CLOCK=$(F_CLOCK)UL -DBOARD=BOARD_$(BOARD)
 188 CDEFS += -DUSE_NONSTANDARD_DESCRIPTOR_NAMES -DNO_STREAM_CALLBACKS -DUSB_DEVICE_ONLY
 189 CDEFS += -DSTATIC_ENDPOINT_CONFIGURATION -DFIXED_CONTROL_ENDPOINT_SIZE=8
 190 CDEFS += -DUSE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
 191
 192
 193 # Place -D or -U options here for ASM sources
 194 ADEFS = -DF_CPU=$(F_CPU)
 195
 196
 197 # Place -D or -U options here for C++ sources
 198 CPPDEFS = -DF_CPU=$(F_CPU)UL
 199 #CPPDEFS += -D__STDC_LIMIT_MACROS
 200 #CPPDEFS += -D__STDC_CONSTANT_MACROS
 201
 202
 203
 204 #---------------- Compiler Options C ----------------
 205 #  -g*:          generate debugging information
 206 #  -O*:          optimization level
 207 #  -f...:        tuning, see GCC manual and avr-libc documentation
 208 #  -Wall...:     warning level
 209 #  -Wa,...:      tell GCC to pass this to the assembler.
 210 #    -adhlns...: create assembler listing
 211 CFLAGS = -g$(DEBUG)
 212 CFLAGS += $(CDEFS)
 213 CFLAGS += -O$(OPT)
 214 CFLAGS += -funsigned-char
 215 CFLAGS += -funsigned-bitfields
 216 CFLAGS += -ffunction-sections
 217 CFLAGS += -fpack-struct
 218 CFLAGS += -fshort-enums
 219 CFLAGS += -finline-limit=20
 220 CFLAGS += -Wall
 221 CFLAGS += -Wstrict-prototypes
 222 CFLAGS += -Wundef
 223 #CFLAGS += -fno-unit-at-a-time
 224 #CFLAGS += -Wunreachable-code
 225 #CFLAGS += -Wsign-compare
 226 CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 227 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 228 CFLAGS += $(CSTANDARD)
 229
 230
 231 #---------------- Compiler Options C++ ----------------
 232 #  -g*:          generate debugging information
 233 #  -O*:          optimization level
 234 #  -f...:        tuning, see GCC manual and avr-libc documentation
 235 #  -Wall...:     warning level
 236 #  -Wa,...:      tell GCC to pass this to the assembler.
 237 #    -adhlns...: create assembler listing
 238 CPPFLAGS = -g$(DEBUG)
 239 CPPFLAGS += $(CPPDEFS)
 240 CPPFLAGS += -O$(OPT)
 241 CPPFLAGS += -funsigned-char
 242 CPPFLAGS += -funsigned-bitfields
 243 CPPFLAGS += -fpack-struct
 244 CPPFLAGS += -fshort-enums
 245 CPPFLAGS += -fno-exceptions
 246 CPPFLAGS += -Wall
 247 CFLAGS += -Wundef
 248 #CPPFLAGS += -mshort-calls
 249 #CPPFLAGS += -fno-unit-at-a-time
 250 #CPPFLAGS += -Wstrict-prototypes
 251 #CPPFLAGS += -Wunreachable-code
 252 #CPPFLAGS += -Wsign-compare
 253 CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 254 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 255 #CPPFLAGS += $(CSTANDARD)
 256
 257
 258 #---------------- Assembler Options ----------------
 259 #  -Wa,...:   tell GCC to pass this to the assembler.
 260 #  -adhlns:   create listing
 261 #  -gstabs:   have the assembler create line number information; note that
 262 #             for use in COFF files, additional information about filenames
 263 #             and function names needs to be present in the assembler source
 264 #             files -- see avr-libc docs [FIXME: not yet described there]
 265 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 266 #       dump that will be displayed for a given single line of source input.
 267 ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 268
 269
 270 #---------------- Library Options ----------------
 271 # Minimalistic printf version
 272 PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
 273
 274 # Floating point printf version (requires MATH_LIB = -lm below)
 275 PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
 276
 277 # If this is left blank, then it will use the Standard printf version.
 278 PRINTF_LIB =
 279 #PRINTF_LIB = $(PRINTF_LIB_MIN)
 280 #PRINTF_LIB = $(PRINTF_LIB_FLOAT)
 281
 282
 283 # Minimalistic scanf version
 284 SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
 285
 286 # Floating point + %[ scanf version (requires MATH_LIB = -lm below)
 287 SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
 288
 289 # If this is left blank, then it will use the Standard scanf version.
 290 SCANF_LIB =
 291 #SCANF_LIB = $(SCANF_LIB_MIN)
 292 #SCANF_LIB = $(SCANF_LIB_FLOAT)
 293
 294
 295 MATH_LIB = -lm
 296
 297
 298 # List any extra directories to look for libraries here.
 299 #     Each directory must be seperated by a space.
 300 #     Use forward slashes for directory separators.
 301 #     For a directory that has spaces, enclose it in quotes.
 302 EXTRALIBDIRS =
 303
 304
 305
 306 #---------------- External Memory Options ----------------
 307
 308 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 309 # used for variables (.data/.bss) and heap (malloc()).
 310 #EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
 311
 312 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 313 # only used for heap (malloc()).
 314 #EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
 315
 316 EXTMEMOPTS =
 317
 318
 319
 320 #---------------- Linker Options ----------------
 321 #  -Wl,...:     tell GCC to pass this to linker.
 322 #    -Map:      create map file
 323 #    --cref:    add cross reference to  map file
 324 LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
 325 LDFLAGS += -Wl,--relax
 326 LDFLAGS += -Wl,--gc-sections
 327 LDFLAGS += $(EXTMEMOPTS)
 328 LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
 329 LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
 330 #LDFLAGS += -T linker_script.x
 331
 332
 333
 334 #---------------- Programming Options (avrdude) ----------------
 335
 336 # Programming hardware: alf avr910 avrisp bascom bsd
 337 # dt006 pavr picoweb pony-stk200 sp12 stk200 stk500
 338 #
 339 # Type: avrdude -c ?
 340 # to get a full listing.
 341 #
 342 AVRDUDE_PROGRAMMER = jtagmkII
 343
 344 # com1 = serial port. Use lpt1 to connect to parallel port.
 345 AVRDUDE_PORT = usb
 346
 347 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
 348 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
 349
 350
 351 # Uncomment the following if you want avrdude's erase cycle counter.
 352 # Note that this counter needs to be initialized first using -Yn,
 353 # see avrdude manual.
 354 #AVRDUDE_ERASE_COUNTER = -y
 355
 356 # Uncomment the following if you do /not/ wish a verification to be
 357 # performed after programming the device.
 358 #AVRDUDE_NO_VERIFY = -V
 359
 360 # Increase verbosity level.  Please use this when submitting bug
 361 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
 362 # to submit bug reports.
 363 #AVRDUDE_VERBOSE = -v -v
 364
 365 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
 366 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
 367 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
 368 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 369
 370
 371
 372 #---------------- Debugging Options ----------------
 373
 374 # For simulavr only - target MCU frequency.
 375 DEBUG_MFREQ = $(F_CPU)
 376
 377 # Set the DEBUG_UI to either gdb or insight.
 378 # DEBUG_UI = gdb
 379 DEBUG_UI = insight
 380
 381 # Set the debugging back-end to either avarice, simulavr.
 382 DEBUG_BACKEND = avarice
 383 #DEBUG_BACKEND = simulavr
 384
 385 # GDB Init Filename.
 386 GDBINIT_FILE = __avr_gdbinit
 387
 388 # When using avarice settings for the JTAG
 389 JTAG_DEV = /dev/com1
 390
 391 # Debugging port used to communicate between GDB / avarice / simulavr.
 392 DEBUG_PORT = 4242
 393
 394 # Debugging host used to communicate between GDB / avarice / simulavr, normally
 395 #     just set to localhost unless doing some sort of crazy debugging when
 396 #     avarice is running on a different computer.
 397 DEBUG_HOST = localhost
 398
 399
 400
 401 #============================================================================
 402
 403
 404 # Define programs and commands.
 405 SHELL = sh
 406 CC = avr-gcc
 407 OBJCOPY = avr-objcopy
 408 OBJDUMP = avr-objdump
 409 SIZE = avr-size
 410 AR = avr-ar rcs
 411 NM = avr-nm
 412 AVRDUDE = avrdude
 413 REMOVE = rm -f
 414 REMOVEDIR = rm -rf
 415 COPY = cp
 416 WINSHELL = cmd
 417
 418 # Define Messages
 419 # English
 420 MSG_ERRORS_NONE = Errors: none
 421 MSG_BEGIN = -------- begin --------
 422 MSG_END = --------  end  --------
 423 MSG_SIZE_BEFORE = Size before:
 424 MSG_SIZE_AFTER = Size after:
 425 MSG_COFF = Converting to AVR COFF:
 426 MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
 427 MSG_FLASH = Creating load file for Flash:
 428 MSG_EEPROM = Creating load file for EEPROM:
 429 MSG_EXTENDED_LISTING = Creating Extended Listing:
 430 MSG_SYMBOL_TABLE = Creating Symbol Table:
 431 MSG_LINKING = Linking:
 432 MSG_COMPILING = Compiling C:
 433 MSG_COMPILING_CPP = Compiling C++:
 434 MSG_ASSEMBLING = Assembling:
 435 MSG_CLEANING = Cleaning project:
 436 MSG_CREATING_LIBRARY = Creating library:
 437
 438
 439
 440
 441 # Define all object files.
 442 OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 443
 444 # Define all listing files.
 445 LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 446
 447
 448 # Compiler flags to generate dependency files.
 449 GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
 450
 451
 452 # Combine all necessary flags and optional flags.
 453 # Add target processor to flags.
 454 ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
 455 ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
 456 ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
 457
 458
 459
 460
 461
 462 # Default target.
 463 all: begin gccversion sizebefore build checkhooks checklibmode checkboard sizeafter end
 464
 465 # Change the build target to build a HEX file or a library.
 466 build: elf hex eep lss sym
 467 #build: lib
 468
 469
 470 elf: $(TARGET).elf
 471 hex: $(TARGET).hex
 472 eep: $(TARGET).eep
 473 lss: $(TARGET).lss
 474 sym: $(TARGET).sym
 475 LIBNAME=lib$(TARGET).a
 476 lib: $(LIBNAME)
 477
 478
 479
 480 # Eye candy.
 481 # AVR Studio 3.x does not check make's exit code but relies on
 482 # the following magic strings to be generated by the compile job.
 483 begin:
 484         @echo
 485         @echo $(MSG_BEGIN)
 486
 487 end:
 488         @echo $(MSG_END)
 489         @echo
 490
 491
 492 # Display size of file.
 493 HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
 494 ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
 495 MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
 496 FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
 497
 498 sizebefore:
 499         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
 500         2>/dev/null; echo; fi
 501
 502 sizeafter:
 503         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
 504         2>/dev/null; echo; fi
 505
 506 checkhooks: build
 507         @echo
 508         @echo ------- Unhooked LUFA Events -------
 509         @$(shell) (grep -s '^Event.*LUFA/.*\\.o' $(TARGET).map | \
 510                    cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \
 511                            echo "(None)"
 512         @echo ------------------------------------
 513
 514 checklibmode:
 515         @echo
 516         @echo ----------- Library Mode -----------
 517         @$(shell) ($(CC) $(ALL_CFLAGS) -E -dM - < /dev/null \
 518                   | grep 'USB_\(DEVICE\|HOST\)_ONLY' | cut -d' ' -f2 | grep ".*") \
 519                   || echo "No specific mode (both device and host mode allowable)."
 520         @echo ------------------------------------
 521
 522 checkboard:
 523         @echo
 524         @echo ---------- Selected Board ----------
 525         @echo Selected board model is $(BOARD).
 526         @echo ------------------------------------
 527
 528 # Display compiler version information.
 529 gccversion :
 530         @$(CC) --version
 531
 532
 533
 534 # Program the device.
 535 program: $(TARGET).hex $(TARGET).eep
 536         $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
 537
 538 flip: $(TARGET).hex
 539         batchisp -hardware usb -device $(MCU) -operation erase f
 540         batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
 541         batchisp -hardware usb -device $(MCU) -operation start reset 0
 542
 543 dfu: $(TARGET).hex
 544         dfu-programmer $(MCU) erase
 545         dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex
 546         dfu-programmer $(MCU) reset
 547
 548 flip-ee: $(TARGET).hex $(TARGET).eep
 549         copy $(TARGET).eep $(TARGET)eep.hex
 550         batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
 551         batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
 552         batchisp -hardware usb -device $(MCU) -operation start reset 0
 553
 554 dfu-ee: $(TARGET).hex $(TARGET).eep
 555         dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
 556         dfu-programmer $(MCU) reset
 557
 558
 559 # Generate avr-gdb config/init file which does the following:
 560 #     define the reset signal, load the target file, connect to target, and set
 561 #     a breakpoint at main().
 562 gdb-config:
 563         @$(REMOVE) $(GDBINIT_FILE)
 564         @echo define reset >> $(GDBINIT_FILE)
 565         @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
 566         @echo end >> $(GDBINIT_FILE)
 567         @echo file $(TARGET).elf >> $(GDBINIT_FILE)
 568         @echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
 569 ifeq ($(DEBUG_BACKEND),simulavr)
 570         @echo load  >> $(GDBINIT_FILE)
 571 endif
 572         @echo break main >> $(GDBINIT_FILE)
 573
 574 debug: gdb-config $(TARGET).elf
 575 ifeq ($(DEBUG_BACKEND), avarice)
 576         @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
 577         @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
 578         $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
 579         @$(WINSHELL) /c pause
 580
 581 else
 582         @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
 583         $(DEBUG_MFREQ) --port $(DEBUG_PORT)
 584 endif
 585         @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
 586
 587
 588
 589
 590 # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
 591 COFFCONVERT = $(OBJCOPY) --debugging
 592 COFFCONVERT += --change-section-address .data-0x800000
 593 COFFCONVERT += --change-section-address .bss-0x800000
 594 COFFCONVERT += --change-section-address .noinit-0x800000
 595 COFFCONVERT += --change-section-address .eeprom-0x810000
 596
 597
 598
 599 coff: $(TARGET).elf
 600         @echo
 601         @echo $(MSG_COFF) $(TARGET).cof
 602         $(COFFCONVERT) -O coff-avr $< $(TARGET).cof
 603
 604
 605 extcoff: $(TARGET).elf
 606         @echo
 607         @echo $(MSG_EXTENDED_COFF) $(TARGET).cof
 608         $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
 609
 610
 611
 612 # Create final output files (.hex, .eep) from ELF output file.
 613 %.hex: %.elf
 614         @echo
 615         @echo $(MSG_FLASH) $@
 616         $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@
 617
 618 %.eep: %.elf
 619         @echo
 620         @echo $(MSG_EEPROM) $@
 621         -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
 622         --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
 623
 624 # Create extended listing file from ELF output file.
 625 %.lss: %.elf
 626         @echo
 627         @echo $(MSG_EXTENDED_LISTING) $@
 628         $(OBJDUMP) -h -z -S $< > $@
 629
 630 # Create a symbol table from ELF output file.
 631 %.sym: %.elf
 632         @echo
 633         @echo $(MSG_SYMBOL_TABLE) $@
 634         $(NM) -n $< > $@
 635
 636
 637
 638 # Create library from object files.
 639 .SECONDARY : $(TARGET).a
 640 .PRECIOUS : $(OBJ)
 641 %.a: $(OBJ)
 642         @echo
 643         @echo $(MSG_CREATING_LIBRARY) $@
 644         $(AR) $@ $(OBJ)
 645
 646
 647 # Link: create ELF output file from object files.
 648 .SECONDARY : $(TARGET).elf
 649 .PRECIOUS : $(OBJ)
 650 %.elf: $(OBJ)
 651         @echo
 652         @echo $(MSG_LINKING) $@
 653         $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
 654
 655
 656 # Compile: create object files from C source files.
 657 $(OBJDIR)/%.o : %.c
 658         @echo
 659         @echo $(MSG_COMPILING) $<
 660         $(CC) -c $(ALL_CFLAGS) $< -o $@
 661
 662
 663 # Compile: create object files from C++ source files.
 664 $(OBJDIR)/%.o : %.cpp
 665         @echo
 666         @echo $(MSG_COMPILING_CPP) $<
 667         $(CC) -c $(ALL_CPPFLAGS) $< -o $@
 668
 669
 670 # Compile: create assembler files from C source files.
 671 %.s : %.c
 672         $(CC) -S $(ALL_CFLAGS) $< -o $@
 673
 674
 675 # Compile: create assembler files from C++ source files.
 676 %.s : %.cpp
 677         $(CC) -S $(ALL_CPPFLAGS) $< -o $@
 678
 679
 680 # Assemble: create object files from assembler source files.
 681 $(OBJDIR)/%.o : %.S
 682         @echo
 683         @echo $(MSG_ASSEMBLING) $<
 684         $(CC) -c $(ALL_ASFLAGS) $< -o $@
 685
 686
 687 # Create preprocessed source for use in sending a bug report.
 688 %.i : %.c
 689         $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
 690
 691
 692 # Target: clean project.
 693 clean: begin clean_list clean_binary end
 694
 695 clean_binary:
 696         $(REMOVE) $(TARGET).hex
 697
 698 clean_list:
 699         @echo $(MSG_CLEANING)
 700         $(REMOVE) $(TARGET).eep
 701         $(REMOVE) $(TARGET)eep.hex
 702         $(REMOVE) $(TARGET).cof
 703         $(REMOVE) $(TARGET).elf
 704         $(REMOVE) $(TARGET).map
 705         $(REMOVE) $(TARGET).sym
 706         $(REMOVE) $(TARGET).lss
 707         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o)
 708         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst)
 709         $(REMOVE) $(SRC:.c=.s)
 710         $(REMOVE) $(SRC:.c=.d)
 711         $(REMOVE) $(SRC:.c=.i)
 712         $(REMOVEDIR) .dep
 713
 714
 715 doxygen:
 716         @echo Generating Project Documentation...
 717         @doxygen Doxygen.conf
 718         @echo Documentation Generation Complete.
 719
 720 clean_doxygen:
 721         rm -rf Documentation
 722
 723 # Create object files directory
 724 $(shell mkdir $(OBJDIR) 2>/dev/null)
 725
 726
 727 # Include the dependency files.
 728 -include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
 729
 730
 731 # Listing of phony targets.
 732 .PHONY : all checkhooks checklibmode checkboard   \
 733 begin finish end sizebefore sizeafter gccversion  \
 734 build elf hex eep lss sym coff extcoff clean      \
 735 clean_list clean_binary program debug gdb-config  \
 736 doxygen dfu flip flip-ee dfu-ee