LUFA/CodeTemplates/makefile_template.avr8

   1 # Hey Emacs, this is a -*- makefile -*-
   2 #----------------------------------------------------------------------------
   3 # WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
   4 #  >> Modified for use with the LUFA project. <<
   5 #
   6 # Released to the Public Domain
   7 #
   8 # Additional material for this makefile was written by:
   9 # Peter Fleury
  10 # Tim Henigan
  11 # Colin O'Flynn
  12 # Reiner Patommel
  13 # Markus Pfaff
  14 # Sander Pool
  15 # Frederik Rouleau
  16 # Carlos Lamas
  17 # Dean Camera
  18 # Opendous Inc.
  19 # Denver Gingerich
  20 #
  21 #----------------------------------------------------------------------------
  22 # On command line:
  23 #
  24 # make all = Make software.
  25 #
  26 # make clean = Clean out built project files.
  27 #
  28 # make coff = Convert ELF to AVR COFF.
  29 #
  30 # make extcoff = Convert ELF to AVR Extended COFF.
  31 #
  32 # make program = Download the hex file to the device, using avrdude.
  33 #                Please customize the avrdude settings below first!
  34 #
  35 # make dfu = Download the hex file to the device, using dfu-programmer (must
  36 #            have dfu-programmer installed).
  37 #
  38 # make flip = Download the hex file to the device, using Atmel FLIP (must
  39 #             have Atmel FLIP installed).
  40 #
  41 # make dfu-ee = Download the eeprom file to the device, using dfu-programmer
  42 #               (must have dfu-programmer installed).
  43 #
  44 # make flip-ee = Download the eeprom file to the device, using Atmel FLIP
  45 #                (must have Atmel FLIP installed).
  46 #
  47 # make doxygen = Generate DoxyGen documentation for the project (must have
  48 #                DoxyGen installed)
  49 #
  50 # make debug = Start either simulavr or avarice as specified for debugging,
  51 #              with avr-gdb or avr-insight as the front end for debugging.
  52 #
  53 # make filename.s = Just compile filename.c into the assembler code only.
  54 #
  55 # make filename.i = Create a preprocessed source file for use in submitting
  56 #                   bug reports to the GCC project.
  57 #
  58 # To rebuild project do "make clean" then "make all".
  59 #----------------------------------------------------------------------------
  60
  61
  62 # MCU name
  63 MCU = ### INSERT NAME OF MICROCONTROLLER MODEL HERE ###
  64
  65
  66 # Targeted chip architecture (see library "Architectures" documentation)
  67 ARCH = AVR8
  68
  69
  70 # Target board (see library "Board Types" documentation, NONE for projects not requiring
  71 # LUFA board drivers). If USER is selected, put custom board drivers in a directory called
  72 # "Board" inside the application directory.
  73 BOARD = ### INSERT NAME OF BOARD HERE, OR NONE IF NO BOARD DRIVERS USED ###
  74
  75
  76 # Processor frequency.
  77 #     This will define a symbol, F_CPU, in all source code files equal to the
  78 #     processor frequency in Hz. You can then use this symbol in your source code to
  79 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
  80 #     automatically to create a 32-bit value in your source code.
  81 #
  82 #     This will be an integer division of F_CLOCK below, as it is sourced by
  83 #     F_CLOCK after it has run through any CPU prescalers. Note that this value
  84 #     does not *change* the processor frequency - it should merely be updated to
  85 #     reflect the processor speed set externally so that the code can use accurate
  86 #     software delays.
  87 F_CPU = ### INSERT PRESCALED SYSTEM CLOCK SPEED HERE, IN HZ ###
  88
  89
  90 # Input clock frequency.
  91 #     This will define a symbol, F_USB, in all source code files equal to the
  92 #     input clock frequency (before any prescaling is performed) in Hz. This value may
  93 #     differ from F_CPU if prescaling is used on the latter, and is required as the
  94 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
  95 #     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
  96 #     at the end, this will be done automatically to create a 32-bit value in your
  97 #     source code.
  98 #
  99 #     If no clock division is performed on the input clock inside the AVR (via the
 100 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 101 F_USB = ### INSERT CLOCK TO USB MODULE HERE, IN HZ ###
 102
 103
 104 # Output format. (can be srec, ihex, binary)
 105 FORMAT = ihex
 106
 107
 108 # Target file name (without extension).
 109 TARGET = ### INSERT NAME OF MAIN FILENAME HERE, WITHOUT EXTENSION ###
 110
 111
 112 # Object files directory
 113 #     To put object files in current directory, use a dot (.), do NOT make
 114 #     this an empty or blank macro!
 115 OBJDIR = .
 116
 117
 118 # Path to the LUFA library
 119 LUFA_PATH = ### INSERT PATH TO LUFA LIBRARY RELATIVE TO PROJECT DIRECTORY HERE ###
 120
 121
 122 # LUFA library compile-time options and predefined tokens (add '-D' before each token)
 123 LUFA_OPTS = ### INSERT LUFA COMPILE TIME TOKENS HERE ###
 124
 125
 126 # Create the LUFA source path variables by including the LUFA root makefile
 127 include $(LUFA_PATH)/LUFA/makefile
 128
 129
 130 # List C source files here. (C dependencies are automatically generated.)
 131 SRC = $(TARGET).c                                                 \
 132           $(LUFA_SRC_USB)                                             \
 133           $(LUFA_SRC_USBCLASS)
 134       ### INSERT ADDITIONAL PROJECT SOURCE FILENAMES OR LUFA MODULE NAMES HERE ###
 135
 136
 137 # List C++ source files here. (C dependencies are automatically generated.)
 138 CPPSRC =
 139
 140
 141 # List Assembler source files here.
 142 #     Make them always end in a capital .S.  Files ending in a lowercase .s
 143 #     will not be considered source files but generated files (assembler
 144 #     output from the compiler), and will be deleted upon "make clean"!
 145 #     Even though the DOS/Win* filesystem matches both .s and .S the same,
 146 #     it will preserve the spelling of the filenames, and gcc itself does
 147 #     care about how the name is spelled on its command-line.
 148 ASRC =
 149
 150
 151 # Optimization level, can be [0, 1, 2, 3, s].
 152 #     0 = turn off optimization. s = optimize for size.
 153 #     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
 154 OPT = s
 155
 156
 157 # List any extra directories to look for include files here.
 158 #     Each directory must be seperated by a space.
 159 #     Use forward slashes for directory separators.
 160 #     For a directory that has spaces, enclose it in quotes.
 161 EXTRAINCDIRS = $(LUFA_PATH)/
 162
 163
 164 # Compiler flag to set the C Standard level.
 165 #     c89   = "ANSI" C
 166 #     gnu89 = c89 plus GCC extensions
 167 #     c99   = ISO C99 standard (not yet fully implemented)
 168 #     gnu99 = c99 plus GCC extensions
 169 CSTANDARD = -std=gnu99
 170
 171
 172 # Place -D or -U options here for C sources
 173 CDEFS  = -DF_CPU=$(F_CPU)UL
 174 CDEFS += -DF_USB=$(F_USB)UL
 175 CDEFS += -DBOARD=BOARD_$(BOARD)
 176 CDEFS += -DARCH=ARCH_$(ARCH)
 177 CDEFS += $(LUFA_OPTS)
 178
 179
 180 # Place -D or -U options here for ASM sources
 181 ADEFS  = -DF_CPU=$(F_CPU)
 182 ADEFS += -DF_USB=$(F_USB)UL
 183 ADEFS += -DBOARD=BOARD_$(BOARD)
 184 ADEFS += -DARCH=ARCH_$(ARCH)
 185 ADEFS += $(LUFA_OPTS)
 186
 187 # Place -D or -U options here for C++ sources
 188 CPPDEFS  = -DF_CPU=$(F_CPU)UL
 189 CPPDEFS += -DF_USB=$(F_USB)UL
 190 CPPDEFS += -DBOARD=BOARD_$(BOARD)
 191 CPPDEFS += -DARCH=ARCH_$(ARCH)
 192 CPPDEFS += $(LUFA_OPTS)
 193
 194
 195 # Debugging format.
 196 #     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.
 197 #     AVR Studio 4.10 requires dwarf-2.
 198 #     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.
 199 DEBUG = dwarf-2
 200
 201
 202 #---------------- Compiler Options C ----------------
 203 #  -g*:          generate debugging information
 204 #  -O*:          optimization level
 205 #  -f...:        tuning, see GCC manual and avr-libc documentation
 206 #  -Wall...:     warning level
 207 #  -Wa,...:      tell GCC to pass this to the assembler.
 208 #    -adhlns...: create assembler listing
 209 CFLAGS = -g$(DEBUG)
 210 CFLAGS += $(CDEFS)
 211 CFLAGS += -O$(OPT)
 212 CFLAGS += -funsigned-char
 213 CFLAGS += -funsigned-bitfields
 214 CFLAGS += -ffunction-sections
 215 CFLAGS += -fno-inline-small-functions
 216 CFLAGS += -fpack-struct
 217 CFLAGS += -fshort-enums
 218 CFLAGS += -fno-strict-aliasing
 219 CFLAGS += -Wall
 220 CFLAGS += -Wstrict-prototypes
 221 CFLAGS += -Wa,-adhlns=$(<:%.c=$(OBJDIR)/%.lst)
 222 CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 223 CFLAGS += $(CSTANDARD)
 224
 225
 226 #---------------- Compiler Options C++ ----------------
 227 #  -g*:          generate debugging information
 228 #  -O*:          optimization level
 229 #  -f...:        tuning, see GCC manual and avr-libc documentation
 230 #  -Wall...:     warning level
 231 #  -Wa,...:      tell GCC to pass this to the assembler.
 232 #    -adhlns...: create assembler listing
 233 CPPFLAGS = -g$(DEBUG)
 234 CPPFLAGS += $(CPPDEFS)
 235 CPPFLAGS += -O$(OPT)
 236 CPPFLAGS += -funsigned-char
 237 CPPFLAGS += -funsigned-bitfields
 238 CPPFLAGS += -fpack-struct
 239 CPPFLAGS += -fshort-enums
 240 CPPFLAGS += -ffunction-sections
 241 CPPFLAGS += -fno-strict-aliasing
 242 CPPFLAGS += -fno-exceptions
 243 CPPFLAGS += -Wall
 244 CPPFLAGS += -Wundef
 245 CPPFLAGS += -Wa,-adhlns=$(<:%.cpp=$(OBJDIR)/%.lst)
 246 CPPFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))
 247 #CPPFLAGS += $(CSTANDARD)
 248
 249
 250 #---------------- Assembler Options ----------------
 251 #  -Wa,...:   tell GCC to pass this to the assembler.
 252 #  -adhlns:   create listing
 253 #  -gstabs:   have the assembler create line number information; note that
 254 #             for use in COFF files, additional information about filenames
 255 #             and function names needs to be present in the assembler source
 256 #             files -- see avr-libc docs [FIXME: not yet described there]
 257 #  -listing-cont-lines: Sets the maximum number of continuation lines of hex
 258 #       dump that will be displayed for a given single line of source input.
 259 ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
 260
 261
 262 #---------------- Library Options ----------------
 263 # Minimalistic printf version
 264 PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min
 265
 266 # Floating point printf version (requires MATH_LIB = -lm below)
 267 PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
 268
 269 # If this is left blank, then it will use the Standard printf version.
 270 PRINTF_LIB =
 271 #PRINTF_LIB = $(PRINTF_LIB_MIN)
 272 #PRINTF_LIB = $(PRINTF_LIB_FLOAT)
 273
 274
 275 # Minimalistic scanf version
 276 SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min
 277
 278 # Floating point + %[ scanf version (requires MATH_LIB = -lm below)
 279 SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
 280
 281 # If this is left blank, then it will use the Standard scanf version.
 282 SCANF_LIB =
 283 #SCANF_LIB = $(SCANF_LIB_MIN)
 284 #SCANF_LIB = $(SCANF_LIB_FLOAT)
 285
 286
 287 MATH_LIB = -lm
 288
 289
 290 # List any extra directories to look for libraries here.
 291 #     Each directory must be seperated by a space.
 292 #     Use forward slashes for directory separators.
 293 #     For a directory that has spaces, enclose it in quotes.
 294 EXTRALIBDIRS =
 295
 296
 297
 298 #---------------- External Memory Options ----------------
 299
 300 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 301 # used for variables (.data/.bss) and heap (malloc()).
 302 #EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff
 303
 304 # 64 KB of external RAM, starting after internal RAM (ATmega128!),
 305 # only used for heap (malloc()).
 306 #EXTMEMOPTS = -Wl,--section-start,.data=0x801100,--defsym=__heap_end=0x80ffff
 307
 308 EXTMEMOPTS =
 309
 310
 311
 312 #---------------- Linker Options ----------------
 313 #  -Wl,...:     tell GCC to pass this to linker.
 314 #    -Map:      create map file
 315 #    --cref:    add cross reference to  map file
 316 LDFLAGS  = -Wl,-Map=$(TARGET).map,--cref
 317 LDFLAGS += -Wl,--relax
 318 LDFLAGS += -Wl,--gc-sections
 319 LDFLAGS += $(EXTMEMOPTS)
 320 LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
 321 LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)
 322 #LDFLAGS += -T linker_script.x
 323
 324
 325
 326 #---------------- Programming Options (avrdude) ----------------
 327
 328 # Programming hardware
 329 # Type: avrdude -c ?
 330 # to get a full listing.
 331 #
 332 AVRDUDE_PROGRAMMER = jtagmkII
 333
 334 # com1 = serial port. Use lpt1 to connect to parallel port.
 335 AVRDUDE_PORT = usb
 336
 337 AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
 338 #AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
 339
 340
 341 # Uncomment the following if you want avrdude's erase cycle counter.
 342 # Note that this counter needs to be initialized first using -Yn,
 343 # see avrdude manual.
 344 #AVRDUDE_ERASE_COUNTER = -y
 345
 346 # Uncomment the following if you do /not/ wish a verification to be
 347 # performed after programming the device.
 348 #AVRDUDE_NO_VERIFY = -V
 349
 350 # Increase verbosity level.  Please use this when submitting bug
 351 # reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
 352 # to submit bug reports.
 353 #AVRDUDE_VERBOSE = -v -v
 354
 355 AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
 356 AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
 357 AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
 358 AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
 359
 360
 361
 362 #---------------- Debugging Options ----------------
 363
 364 # For simulavr only - target MCU frequency.
 365 DEBUG_MFREQ = $(F_CPU)
 366
 367 # Set the DEBUG_UI to either gdb or insight.
 368 # DEBUG_UI = gdb
 369 DEBUG_UI = insight
 370
 371 # Set the debugging back-end to either avarice, simulavr.
 372 DEBUG_BACKEND = avarice
 373 #DEBUG_BACKEND = simulavr
 374
 375 # GDB Init Filename.
 376 GDBINIT_FILE = __avr_gdbinit
 377
 378 # When using avarice settings for the JTAG
 379 JTAG_DEV = /dev/com1
 380
 381 # Debugging port used to communicate between GDB / avarice / simulavr.
 382 DEBUG_PORT = 4242
 383
 384 # Debugging host used to communicate between GDB / avarice / simulavr, normally
 385 #     just set to localhost unless doing some sort of crazy debugging when
 386 #     avarice is running on a different computer.
 387 DEBUG_HOST = localhost
 388
 389
 390
 391 #============================================================================
 392
 393
 394 # Define programs and commands.
 395 SHELL = sh
 396 CC = avr-gcc
 397 OBJCOPY = avr-objcopy
 398 OBJDUMP = avr-objdump
 399 SIZE = avr-size
 400 AR = avr-ar rcs
 401 NM = avr-nm
 402 AVRDUDE = avrdude
 403 REMOVE = rm -f
 404 REMOVEDIR = rm -rf
 405 COPY = cp
 406 WINSHELL = cmd
 407
 408
 409 # Define Messages
 410 # English
 411 MSG_ERRORS_NONE = Errors: none
 412 MSG_BEGIN = -------- begin --------
 413 MSG_END = --------  end  --------
 414 MSG_SIZE_BEFORE = Size before:
 415 MSG_SIZE_AFTER = Size after:
 416 MSG_COFF = Converting to AVR COFF:
 417 MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
 418 MSG_FLASH = Creating load file for Flash:
 419 MSG_EEPROM = Creating load file for EEPROM:
 420 MSG_EXTENDED_LISTING = Creating Extended Listing:
 421 MSG_SYMBOL_TABLE = Creating Symbol Table:
 422 MSG_LINKING = Linking:
 423 MSG_COMPILING = Compiling C:
 424 MSG_COMPILING_CPP = Compiling C++:
 425 MSG_ASSEMBLING = Assembling:
 426 MSG_CLEANING = Cleaning project:
 427 MSG_CREATING_LIBRARY = Creating library:
 428
 429
 430
 431
 432 # Define all object files.
 433 OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 434
 435 # Define all listing files.
 436 LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 437
 438
 439 # Compiler flags to generate dependency files.
 440 GENDEPFLAGS = -MMD -MP -MF .dep/$(@F).d
 441
 442
 443 # Combine all necessary flags and optional flags.
 444 # Add target processor to flags.
 445 ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)
 446 ALL_CPPFLAGS = -mmcu=$(MCU) -I. -x c++ $(CPPFLAGS) $(GENDEPFLAGS)
 447 ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)
 448
 449
 450
 451
 452
 453 # Default target.
 454 all: begin gccversion sizebefore build sizeafter end
 455
 456 # Change the build target to build a HEX file or a library.
 457 build: elf hex eep lss sym
 458 #build: lib
 459
 460
 461 elf: $(TARGET).elf
 462 hex: $(TARGET).hex
 463 eep: $(TARGET).eep
 464 lss: $(TARGET).lss
 465 sym: $(TARGET).sym
 466 LIBNAME=lib$(TARGET).a
 467 lib: $(LIBNAME)
 468
 469
 470
 471 # Eye candy.
 472 # AVR Studio 3.x does not check make's exit code but relies on
 473 # the following magic strings to be generated by the compile job.
 474 begin:
 475         @echo
 476         @echo $(MSG_BEGIN)
 477
 478 end:
 479         @echo $(MSG_END)
 480         @echo
 481
 482
 483 # Display size of file.
 484 HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex
 485 ELFSIZE = $(SIZE) $(MCU_FLAG) $(FORMAT_FLAG) $(TARGET).elf
 486 MCU_FLAG = $(shell $(SIZE) --help | grep -- --mcu > /dev/null && echo --mcu=$(MCU) )
 487 FORMAT_FLAG = $(shell $(SIZE) --help | grep -- --format=.*avr > /dev/null && echo --format=avr )
 488
 489
 490 sizebefore:
 491         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \
 492         2>/dev/null; echo; fi
 493
 494 sizeafter:
 495         @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
 496         2>/dev/null; echo; fi
 497
 498
 499
 500 # Display compiler version information.
 501 gccversion :
 502         @$(CC) --version
 503
 504
 505 # Program the device.
 506 program: $(TARGET).hex $(TARGET).eep
 507         $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
 508
 509 flip: $(TARGET).hex
 510         batchisp -hardware usb -device $(MCU) -operation erase f
 511         batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
 512         batchisp -hardware usb -device $(MCU) -operation start reset 0
 513
 514 dfu: $(TARGET).hex
 515         dfu-programmer $(MCU) erase
 516         dfu-programmer $(MCU) flash $(TARGET).hex
 517         dfu-programmer $(MCU) reset
 518
 519 flip-ee: $(TARGET).hex $(TARGET).eep
 520         $(COPY) $(TARGET).eep $(TARGET)eep.hex
 521         batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
 522         batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
 523         batchisp -hardware usb -device $(MCU) -operation start reset 0
 524         $(REMOVE) $(TARGET)eep.hex
 525
 526 dfu-ee: $(TARGET).hex $(TARGET).eep
 527         dfu-programmer $(MCU) eeprom-flash $(TARGET).eep
 528         dfu-programmer $(MCU) reset
 529
 530
 531 # Generate avr-gdb config/init file which does the following:
 532 #     define the reset signal, load the target file, connect to target, and set
 533 #     a breakpoint at main().
 534 gdb-config:
 535         @$(REMOVE) $(GDBINIT_FILE)
 536         @echo define reset >> $(GDBINIT_FILE)
 537         @echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
 538         @echo end >> $(GDBINIT_FILE)
 539         @echo file $(TARGET).elf >> $(GDBINIT_FILE)
 540         @echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)
 541 ifeq ($(DEBUG_BACKEND),simulavr)
 542         @echo load  >> $(GDBINIT_FILE)
 543 endif
 544         @echo break main >> $(GDBINIT_FILE)
 545
 546 debug: gdb-config $(TARGET).elf
 547 ifeq ($(DEBUG_BACKEND), avarice)
 548         @echo Starting AVaRICE - Press enter when "waiting to connect" message displays.
 549         @$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \
 550         $(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)
 551         @$(WINSHELL) /c pause
 552
 553 else
 554         @$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \
 555         $(DEBUG_MFREQ) --port $(DEBUG_PORT)
 556 endif
 557         @$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)
 558
 559
 560
 561
 562 # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.
 563 COFFCONVERT = $(OBJCOPY) --debugging
 564 COFFCONVERT += --change-section-address .data-0x800000
 565 COFFCONVERT += --change-section-address .bss-0x800000
 566 COFFCONVERT += --change-section-address .noinit-0x800000
 567 COFFCONVERT += --change-section-address .eeprom-0x810000
 568
 569
 570
 571 coff: $(TARGET).elf
 572         @echo
 573         @echo $(MSG_COFF) $(TARGET).cof
 574         $(COFFCONVERT) -O coff-avr $< $(TARGET).cof
 575
 576
 577 extcoff: $(TARGET).elf
 578         @echo
 579         @echo $(MSG_EXTENDED_COFF) $(TARGET).cof
 580         $(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof
 581
 582
 583
 584 # Create final output files (.hex, .eep) from ELF output file.
 585 %.hex: %.elf
 586         @echo
 587         @echo $(MSG_FLASH) $@
 588         $(OBJCOPY) -O $(FORMAT) -R .eeprom -R .fuse -R .lock -R .signature $< $@
 589
 590 %.eep: %.elf
 591         @echo
 592         @echo $(MSG_EEPROM) $@
 593         -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \
 594         --change-section-lma .eeprom=0 --no-change-warnings -O $(FORMAT) $< $@ || exit 0
 595
 596 # Create extended listing file from ELF output file.
 597 %.lss: %.elf
 598         @echo
 599         @echo $(MSG_EXTENDED_LISTING) $@
 600         $(OBJDUMP) -h -S -z $< > $@
 601
 602 # Create a symbol table from ELF output file.
 603 %.sym: %.elf
 604         @echo
 605         @echo $(MSG_SYMBOL_TABLE) $@
 606         $(NM) -n $< > $@
 607
 608
 609
 610 # Create library from object files.
 611 .SECONDARY : $(TARGET).a
 612 .PRECIOUS : $(OBJ)
 613 %.a: $(OBJ)
 614         @echo
 615         @echo $(MSG_CREATING_LIBRARY) $@
 616         $(AR) $@ $(OBJ)
 617
 618
 619 # Link: create ELF output file from object files.
 620 .SECONDARY : $(TARGET).elf
 621 .PRECIOUS : $(OBJ)
 622 %.elf: $(OBJ)
 623         @echo
 624         @echo $(MSG_LINKING) $@
 625         $(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)
 626
 627
 628 # Compile: create object files from C source files.
 629 $(OBJDIR)/%.o : %.c
 630         @echo
 631         @echo $(MSG_COMPILING) $<
 632         $(CC) -c $(ALL_CFLAGS) $< -o $@
 633
 634
 635 # Compile: create object files from C++ source files.
 636 $(OBJDIR)/%.o : %.cpp
 637         @echo
 638         @echo $(MSG_COMPILING_CPP) $<
 639         $(CC) -c $(ALL_CPPFLAGS) $< -o $@
 640
 641
 642 # Compile: create assembler files from C source files.
 643 %.s : %.c
 644         $(CC) -S $(ALL_CFLAGS) $< -o $@
 645
 646
 647 # Compile: create assembler files from C++ source files.
 648 %.s : %.cpp
 649         $(CC) -S $(ALL_CPPFLAGS) $< -o $@
 650
 651
 652 # Assemble: create object files from assembler source files.
 653 $(OBJDIR)/%.o : %.S
 654         @echo
 655         @echo $(MSG_ASSEMBLING) $<
 656         $(CC) -c $(ALL_ASFLAGS) $< -o $@
 657
 658
 659 # Create preprocessed source for use in sending a bug report.
 660 %.i : %.c
 661         $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
 662
 663
 664 # Target: clean project.
 665 clean: begin clean_list end
 666
 667 clean_list :
 668         @echo
 669         @echo $(MSG_CLEANING)
 670         $(REMOVE) $(TARGET).hex
 671         $(REMOVE) $(TARGET).eep
 672         $(REMOVE) $(TARGET).cof
 673         $(REMOVE) $(TARGET).elf
 674         $(REMOVE) $(TARGET).map
 675         $(REMOVE) $(TARGET).sym
 676         $(REMOVE) $(TARGET).lss
 677         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
 678         $(REMOVE) $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
 679         $(REMOVE) $(SRC:.c=.s)
 680         $(REMOVE) $(SRC:.c=.d)
 681         $(REMOVE) $(SRC:.c=.i)
 682         $(REMOVEDIR) .dep
 683
 684 doxygen:
 685         @echo Generating Project Documentation \($(TARGET)\)...
 686         @doxygen Doxygen.conf
 687         @echo Documentation Generation Complete.
 688
 689 clean_doxygen:
 690         rm -rf Documentation
 691
 692 checksource:
 693         @for f in $(SRC) $(CPPSRC) $(ASRC); do \
 694                 if [ -f $$f ]; then \
 695                         echo "Found Source File: $$f" ; \
 696                 else \
 697                         echo "Source File Not Found: $$f" ; \
 698                 fi; done
 699
 700
 701 # Create object files directory
 702 $(shell mkdir $(OBJDIR) 2>/dev/null)
 703
 704
 705 # Include the dependency files.
 706 -include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)
 707
 708
 709 # Listing of phony targets.
 710 .PHONY : all begin finish end sizebefore sizeafter gccversion \
 711 build elf hex eep lss sym coff extcoff doxygen clean          \
 712 clean_list clean_doxygen program dfu flip flip-ee dfu-ee      \
 713 debug gdb-config checksource