X-Git-Url: http://git.linex4red.de/pub/lufa.git/blobdiff_plain/ecd82778cf9a53e34f13d9ce6dcd7e1a4cf76b70..8ea5c631c8d690df48c15a4dea12777c5929c19d:/Projects/AVRISP/AVRISP.txt

diff --git a/Projects/AVRISP/AVRISP.txt b/Projects/AVRISP/AVRISP.txt
index 9e5a4554f..8d299e25a 100644
--- a/Projects/AVRISP/AVRISP.txt
+++ b/Projects/AVRISP/AVRISP.txt
@@ -50,20 +50,51 @@
  *  \section SSec_Description Project Description: 
  *
  *  Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
- *  microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio.
+ *  microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
+ *  most basic form, it allows for the programming of 5V AVRs from within AVRStudio with no special hardware other than
+ *  the USB AVR and the parts needed for the USB interface. If the user desires, more advanced circuits incorporating
+ *  level conversion can be made to allow for the programming of 3.3V AVR designs.
  *
  *  This device spoofs Atmel's official AVRISP-MKII device PID so that it remains compatible with Atmel's AVRISP-MKII
  *  drivers. When promted, direct your OS to install Atmel's AVRISP-MKII drivers provided with AVRStudio.
  *
+ *  Note that this design currently has several limitations:
+ *    - Minimum target clock speed of 500KHz due to hardware SPI used
+ *    - No reversed/shorted target connector detection and notification
+ *
+ *  On AVR models with an ADC converter, ACC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
+ *  set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
+ *  without an ADC converter, VTARGET will report at a fixed 5V level.
+ *
  *  \section SSec_Options Project Options
  *
  *  The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
  *
  *  <table>
  *   <tr>
- *    <td>
- *     None
- *    </td>
+ *    <td><b>Define Name:</b></td>
+ *    <td><b>Location:</b></td>
+ *    <td><b>Description:</b></td>
+ *   </tr>
+ *   <tr>
+ *    <td>RESET_LINE_PORT</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>PORT register for the programmer's target RESET line.</td>
+ *   </tr>
+ *   <tr>
+ *    <td>RESET_LINE_DDR</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>DDR register for the programmer's target RESET line.</td>
+ *   </tr>
+ *   <tr>
+ *    <td>RESET_LINE_MASK</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>Mask for the programmer's target RESET line on the chosen port.</td>
+ *   </tr>
+ *   <tr>
+ *    <td>VTARGET_ADC_CHANNEL</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>ADC channel number (on supported AVRs) to use for VTARGET level detection.</td> 
  *   </tr>
  *  </table>
  */