X-Git-Url: http://git.linex4red.de/pub/lufa.git/blobdiff_plain/e277ff0cf45e68fc16287b2fd2a054ae4e6a6ea8..34e0fed4ca7e2804d4e0ed5f1d36e08dca659ba0:/LUFA/ManPages/ChangeLog.txt

diff --git a/LUFA/ManPages/ChangeLog.txt b/LUFA/ManPages/ChangeLog.txt
index d93b2f089..03e55b962 100644
--- a/LUFA/ManPages/ChangeLog.txt
+++ b/LUFA/ManPages/ChangeLog.txt
@@ -8,14 +8,32 @@
   *
   *  \section Sec_ChangeLogXXXXXX Version XXXXXX
   *  <b>New:</b>
+  *  - Added new ADC_DisableChannel() function (thanks to Mich Davis)
+  *  - Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set
+  *    the VTARGET reference voltage and scale factor
   *
   *  <b>Changed:</b>
-  *  - The TeensyHID bootloader has been removed, per request from Paul at PJRC
+  *  - The RingBuff library code has been replaced in the XPLAINBridge, Benito and USBtoSerial projects with an ultra lightweight
+  *    ring buffer to help improve the reliability of the projects
+  *  - The EEPROM stream read/write functions now use eeprom_update_byte() instead of eeprom_write_byte(), so that only
+  *    changed bytes are written to EEPROM to preserve its lifespan
+  *  - Changed over the AVRISP-MKII and TemperatureDataLogger projects to use eeprom_update_byte() when writing non-volatile
+  *    parameters to EEPROM to preserve its lifespan
+  *  - Removed unused line encoding data and control requests from the CDC Bootloader code, to save space
   *
   *  <b>Fixed:</b>
-  *
-  *  \section Sec_ChangeLog100512 Version 100512
-  *
+  *  - Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from
+  *    the last page of FLASH (thanks to Gerard Sexton)
+  *  - Fixed AVRISP project not sending a full erase-and-write EEPROM command to XMEGA targets when writing to the EEPROM
+  *    instead of the split write-only command (thanks to Tim Margush)
+  *  - Fixed RNDISEthernet demos crashing when calculating checksums for Ethernet/TCP packets of more than ~500 bytes due to
+  *    an overflow in the checksum calculation loop (thanks to Kevin Malec)
+  *  - Fixed XPLAINBridge project not correctly reading the XMEGA's supply voltage when reporting back to the host
+  *  - Fixed incorrect signature for the ATMEGA32U2 in the DFU bootloader (thanks to Axel Rohde)
+  *  - Fixed internal device serial not being accessible on the ATMEGAXXU2 AVRs (thanks to Axel Rohde)
+  *  - Fixed void pointer arithmetic in ConfigDescriptor.h breaking C++ compatibility (thanks to Michael Hennebry)
+  *
+  *  \section Sec_ChangeLog100513 Version 100513
   *  <b>New:</b>
   *  - Added incomplete MIDIToneGenerator project
   *  - Added new Relay Controller Board project (thanks to OBinou)
@@ -53,8 +71,16 @@
   *    properly reset to their defaults
   *  - Device mode class driver callbacks are now fired before the control request status stage is sent to prevent the host from
   *    timing out if another request is immediately fired and the device has a lengthy callback routine
+  *  - The TeensyHID bootloader has been removed, per request from Paul at PJRC
+  *  - The LIBUSB_FILTERDRV_COMPAT compile time option in the XPLAINBridge and AVRISP-MKII projects has been renamed
+  *    LIBUSB_DRIVER_COMPAT, as it applies to all software on all platforms using the libUSB driver
   *
   *  <b>Fixed:</b>
+  *  - Fixed possible device lockup when INTERRUPT_CONTROL_ENDPOINT is enabled and the control endpoint is not properly
+  *    selected when the ISR completes
+  *  - Fixed AVRISP-MKII clone project not correctly issuing LOAD EXTENDED ADDRESS commands when the extended address
+  *    boundary is crossed during programming or readback (thanks to Gerard Sexton)
+  *  - Fixed warnings when building the AVRISP-MKII clone project with the ENABLE_XPROG_PROTOCOL compile time option disabled
   *  - Fixed software PDI/TPI programming mode in the AVRISP project not correctly toggling just the clock pin
   *  - Fixed TWI_StartTransmission() corrupting the contents of the GPIOR0 register
   *  - Fixed TWI driver not aborting when faced with no response after attempting to address a device on the bus
@@ -80,7 +106,6 @@
   *    HID_HOST_BOOT_PROTOCOL_ONLY compile time option is set
   *  - Fixed INTERRUPT_CONTROL_ENDPOINT compile time option preventing other interrupts from occuring while the control endpoint
   *    request is being processed, causing possible lockups if a USB interrupt occurs during a transfer
-  *  - Fixed TeensyHID bootloader not working on some USB AVR models with the official TeensyLoader GUI application
   *  - Remove incorrect Abstract Call Management class specific descriptor from the CDC demos, bootloaders and projects
   *
   *  \section Sec_ChangeLog100219 Version 100219