X-Git-Url: http://git.linex4red.de/pub/lufa.git/blobdiff_plain/a8b66f318dda3cc18dfcedaa3af3d01ab68b82e8..HEAD:/Projects/XPLAINBridge/XPLAINBridge.txt

diff --git a/Projects/XPLAINBridge/XPLAINBridge.txt b/Projects/XPLAINBridge/XPLAINBridge.txt
index 353241788..ce9784feb 100644
--- a/Projects/XPLAINBridge/XPLAINBridge.txt
+++ b/Projects/XPLAINBridge/XPLAINBridge.txt
@@ -10,7 +10,7 @@
  *
  *  The following list indicates what microcontrollers are compatible with this project.
  *
- *  - AT90USB1287
+ *  \li AT90USB1287
  *
  *  \section Sec_Info USB Information:
  *
@@ -38,7 +38,7 @@
  *    <td>2) Atmel AVRISP MKII Protocol Specification</td>
  *   </tr>
  *   <tr>
- *    <td><b>Usable Speeds:</b></td>
+ *    <td><b>Supported USB Speeds:</b></td>
  *    <td>1) Full Speed Mode</td>
  *    <td>2) Full Speed Mode</td>
  *   </tr>
@@ -47,13 +47,13 @@
  *  \section Sec_Description Project Description:
  *
  *  This project serves a dual purpose. When loaded into the USB AVR on the XPLAIN board, it will act as either a USB to Serial
- *  converter for the XPLAIN's hardware USART (at a speed of 9600 baud), or an AVRStudio compatible PDI programmer for the XMEGA.
+ *  converter for the XPLAIN's hardware USART (at a speed of 9600 baud), or an Atmel Studio compatible PDI programmer for the XMEGA.
  *  This project replaces the firmware preloaded onto the XPLAIN's onboard AT90USB1287 microcontroller.
  *
  *  When power to the board is applied, the TDI pin (pin 9) of the USB AVR's JTAG port is read. If the pin is left high, the device
  *  will enumerate as a regular COM port on the host, which can then be opened and data exchanged between the XMEGA and Host as if
  *  the XMEGA was connected directly to the host's serial port. If the pin is pulled low by shorting it to GND (pin 10), the device
- *  will enumerate as an AVRISP-MKII to the host, so that the XMEGA can be reprogrammed by AVRStudio or other compatible software
+ *  will enumerate as an AVRISP-MKII to the host, so that the XMEGA can be reprogrammed by Atmel Studio or other compatible software
  *  such as avrdude by connecting to the board as if it was an Atmel AVRISP-MKII programmer.
  *
  *  After running this project in serial bridge mode for the first time on a new computer, you will need to supply the .INF file
@@ -74,20 +74,15 @@
  *
  *  <table>
  *   <tr>
- *    <td><b>Define Name:</b></td>
- *    <td><b>Location:</b></td>
- *    <td><b>Description:</b></td>
+ *    <th><b>Define Name:</b></th>
+ *    <th><b>Location:</b></th>
+ *    <th><b>Description:</b></th>
  *   </tr>
  *   <tr>
- *    <td>BUFFER_SIZE</td>
- *    <td>LightweightRingBuff.h</td>
- *    <td>Defines the maximum number of bytes which can be buffered in each Ring Buffer when in serial bridge mode.</td>
- *   </tr>
- *   <tr>
- *    <td>LIBUSB_DRIVER_COMPAT</td>
- *    <td>Makefile LUFA_OPTS</td>
- *    <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making
- *        the code compatible with software such as avrdude (all platforms) that use the libUSB driver.
+ *    <td>FIRMWARE_VERSION_MINOR</td>
+ *    <td>AppConfig.h</td>
+ *    <td>Define to set the minor firmware revision nunber reported to the host on request. By default this will use a firmware version compatible
+ *        with the latest Atmel IDE version, however if desired the reported minor value can be adjusted here.</td>
  *   </tr>
  *  </table>
  */