X-Git-Url: http://git.linex4red.de/pub/lufa.git/blobdiff_plain/8d22cedfc4a1f76b1999f333aecd4c76e34a22e7..refs/heads/master:/Bootloaders/DFU/BootloaderDFU.txt

diff --git a/Bootloaders/DFU/BootloaderDFU.txt b/Bootloaders/DFU/BootloaderDFU.txt
index 2ada35ea2..b2540a5b6 100644
--- a/Bootloaders/DFU/BootloaderDFU.txt
+++ b/Bootloaders/DFU/BootloaderDFU.txt
@@ -12,8 +12,8 @@
  *
  *  \li Series 7 USB AVRs (AT90USBxxx7)
  *  \li Series 6 USB AVRs (AT90USBxxx6)
- *  \li Series 4 USB AVRs (ATMEGAxxU4)
- *  \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2)
+ *  \li Series 4 USB AVRs (ATMEGAxxU4) - <i>See \ref SSec_Aux_Space</i>
+ *  \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - <i>See \ref SSec_Aux_Space</i>
  *
  *  \section Sec_Info USB Information:
  *
@@ -55,6 +55,30 @@
  *  When the bootloader is running, the board's LED(s) will flash at regular intervals to distinguish the
  *  bootloader from the normal user application.
  *
+ *  \section Sec_Running Running the Bootloader
+ *
+ *  On the USB AVR8 devices, setting the \c HWBE device fuse will cause the bootloader to run if the \c HWB pin of
+ *  the AVR is grounded when the device is reset.
+ *
+ *  The are two behaviours of this bootloader, depending on the device's fuses:
+ *
+ *  <b>If the device's BOOTRST fuse is set</b>, the bootloader will run any time the system is reset from
+ *  the external reset pin, unless no valid user application has been loaded. To initiate the bootloader, the
+ *  device's external reset pin should be grounded momentarily.
+ *
+ *  <b>If the device's BOOTRST fuse is not set</b>, the bootloader will run only if initiated via a software
+ *  jump, or if the \c HWB pin was low during the last device reset (if the \c HWBE fuse is set).
+ *
+ *  For board specific exceptions to the above, see below.
+ *
+ *  \subsection SSec_XPLAIN Atmel Xplain Board
+ *  Ground the USB AVR JTAG's \c TCK pin to ground when powering on the board to start the bootloader. This assumes the
+ *  \c HWBE fuse is cleared and the \c BOOTRST fuse is set as the HWBE pin is not user accessible on this board.
+ *
+ *  \subsection SSec_Leonardo Arduino Leonardo Board
+ *  Ground \c IO13 when powering the board to start the bootloader. This assumes the \c HWBE fuse is cleared and the
+ *  \c BOOTRST fuse is set as the HWBE pin is not user accessible on this board.
+ *
  *  \section Sec_Installation Driver Installation
  *
  *  This bootloader is designed to be compatible with Atmel's provided Windows DFU class drivers. You will need to
@@ -117,7 +141,7 @@
  *  #define BOOTLOADER_MAGIC_SIGNATURE         0xDCFB
  *
  *  #define BOOTLOADER_CLASS_SIGNATURE_START   (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 4))
- *  #define BOOTLOADER_DFU_SIGNATURE           0xDFB1
+ *  #define BOOTLOADER_DFU_SIGNATURE           0xDF10
  *
  *  #define BOOTLOADER_ADDRESS_START           (BOOTLOADER_API_TABLE_START + (BOOTLOADER_API_TABLE_SIZE - 8))
  *  #define BOOTLOADER_ADDRESS_LENGTH          4
@@ -150,6 +174,16 @@
  *  |                            |
  *  |                            |
  *  |                            |
+ *  |                            |
+ *  +----------------------------+ FLASHEND - BOOT_AUX_SECTION_SIZE
+ *  | Booloader Start Trampoline |
+ *  | (Not User App. Accessible) |
+ *  +----------------------------+ FLASHEND - (BOOT_AUX_SECTION_SIZE - 4)
+ *  |                            |
+ *  |     Auxillery Bootloader   |
+ *  |  Space for Smaller Devices |
+ *  | (Not User App. Accessible) |
+ *  |                            |
  *  +----------------------------+ FLASHEND - BOOT_SECTION_SIZE
  *  |                            |
  *  |   Bootloader Application   |
@@ -167,15 +201,27 @@
  *  +----------------------------+ FLASHEND
  *  \endverbatim
  *
+ *  \subsection SSec_Aux_Space Auxiliary Bootloader Section
+ *  To make the bootloader function on smaller devices (those with a physical
+ *  bootloader section of smaller than 6KB)
+ *
+ *  \section Sec_KnownIssues Known Issues:
+ *
+ *  \par On Linux machines, the DFU bootloader is inaccessible.
+ *  On many Linux systems, non-root users do not have automatic access to newly
+ *  inserted DFU devices. Root privileges or a UDEV rule is required to gain
+ *  access.
+ *  See <a href=https://groups.google.com/d/msg/lufa-support/CP9cy2bc8yo/kBqsOu-RBeMJ>here</a> for resolution steps.
+ *
  *  \section Sec_Options Project Options
  *
  *  The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
  *
  *  <table>
  *   <tr>
- *    <td><b>Define Name:</b></td>
- *    <td><b>Location:</b></td>
- *    <td><b>Description:</b></td>
+ *    <th><b>Define Name:</b></th>
+ *    <th><b>Location:</b></th>
+ *    <th><b>Description:</b></th>
  *   </tr>
  *   <tr>
  *    <td>SECURE_MODE</td>