*
* \section Sec_ChangeLogXXXXXX Version XXXXXX
* <b>New:</b>
+ * - Added new SCSI_ASENSE_NOT_READY_TO_READY_CHANGE constant to the Mass Storage class driver, to indicate when a previously
+ * not ready removable medium has now become ready for the host's use (thanks to Martin Degelsegger)
+ * - Moved the Pipe and Endpoint stream related code to two new USB library core source files EndpointStream.c and PipeStream.c
+ * - Added new USB_Device_GetFrameNumber() and USB_Host_GetFrameNumber() functions to retrieve the current USB frame number
+ * - Added new USB_Host_EnableSOFEvents(), USB_Host_DisableSOFEvents() and EVENT_USB_Host_StartOfFrame() for the user application
+ * handling of USB Start of Frame events while in USB Host mode
+ * - Added new PRNT_Host_BytesReceived(), PRNT_Host_ReceiveByte(), PRNT_Host_SendByte() and PRNT_Host_Flush() functions to the
+ * Print Host Class driver
+ * - Added class specific descriptor alternative struct type defines with standard USB-IF element naming
+ * - Added new project makefile template to the library and moved board driver stub files into in a new "CodeTemplates" directory
+ * - Added board hardware driver support for the Olimex AVR-USB-162 development board (thanks to Steve Fawcett)
+ * - Added board hardware driver support for the Kernel Concepts USBFOO development board
+ * - Added board hardware driver support for the Linnix UDIP development board
+ * - Added board hardware driver support for the Busware BUI development board
+ * - Added board hardware driver support for the Arduino Uno development board
+ * - Added board hardware driver support for the Busware CUL V3 868MHZ radio board (thanks to Dirk Tostmann)
+ * - Added board hardware driver support for the Blackcat USB JTAG board (thanks to the PSGroove team)
+ * - Added board hardware driver support for the Maximus board (thanks to the PSGroove team)
+ * - Added board hardware driver support for the Minimus board (thanks to the PSGroove team)
+ * - Added default test tone generation mode to the Device mode AudioInput demos
+ * - Added new NO_CLASS_DRIVER_AUTOFLUSH compile time option to disable automatic flushing of interfaces when the USB management
+ * tasks for each driver is called
+ * - Added standard keyboard HID report scancode defines (thanks to Laszlo Monda)
+ * - Added new Pipe_GetBusyBanks(), Endpoint_GetBusyBanks() and Endpoint_AbortPendingIN() functions
+ * - Added new NO_BLOCK_SUPPORT, NO_EEPROM_BYTE_SUPPORT, NO_FLASH_BYTE_SUPPORT and NO_LOCK_BYTE_WRITE_SUPPORT compile time options to the
+ * CDC class bootloader
+ *
+ * <b>Changed:</b>
+ * - Removed complicated logic for the Endpoint_ConfigureEndpoint() function to use inlined or function called versions
+ * depending of if the given bank size is a compile time constant, as the compiler does a better job of optimizing
+ * with basic code
+ * - Changed over all device demos to use a clearer algorithm for the configuring of the application's endpoints
+ * - Added missing DataflashManager_CheckDataflashOperation() function to the MassStorageKeyboard demo, removed redundant
+ * SCSI_Codes.h file as these values are part of the MassStorage Class Driver
+ * - Added compile time error to the AVRISP-MKII project when built for the U4 chips, as the default VTARGET detection ADC channel
+ * does not exist on these chips (thanks to Marco)
+ * - Changed all Device mode LowLevel demos and Device Class drivers so that the control request is acknowledged and any data
+ * transferred as quickly as possible without any processing inbetween sections, so that long callbacks or event handlers will
+ * not break communications with the host by exceeding the maximum control request stage timeout period
+ * - Changed the signature of the CALLBACK_USB_GetDescriptor() callback function so that the descriptor pointer is const, to remove
+ * the need for extra casting inside the callback (thanks to Jonathan Kollasch)
+ * - Reduced HOST_DEVICE_SETTLE_DELAY_MS to 1000ms down from 1500ms to improve device compatibility while in USB Host mode
+ * - Changed over all demos, drivers and internal functions to use the current frame number over the Start of Frame flag where possible
+ * to free up the Start of Frame flag for interrupt use in the user application
+ * - All project makefiles now correctly clean intermediate build files from assembly and C++ sources (thanks to Daniel Czigany)
+ * - Removed the EVENT_USB_InitFailure() event, not specifying a USB mode correctly now defaults to UID selection mode
+ * - Renamed and moved class driver common constant definitions to make the naming scheme more uniform
+ * - Changed default value for the reset polarity parameter in the AVRISP-MKII project so that it defaults to active low drive
+ * - Changed configuration descriptor parser for all host mode projects and class drivers to ensure better compatibility with devices
+ * - Moved the USB mode specifier constants into a new enum, so that they are semantically related to one another
+ * - Renamed ENDPOINT_DOUBLEBANK_SUPPORTED() to ENDPOINT_BANKS_SUPPORTED() and changed it to return the maximum number of supported banks for
+ * the given endpoint
+ * - Better algorithm to extract and convert the internal device serial number into a string descriptor (if present)
+ * - All USB class drivers are now automatically included when LUFA/Drivers/USB.h is included, and no longer need to be seperately included
+ * - All LowLevel demos changed to use the constants and types defined in the USB class drivers
+ * - Changed AudioInput and AudioOutput demos to reload the next sample via an interrupt rather than polling the sample timer
+ * - The MIDI class drivers now automatically flushes the MIDI interface when the MIDI class driver's USBTask() function is called
+ * - Rescue clock of the AVRISP-MKII moved to the AVR's OCR1A pin, so that the clock can be generated at all times
+ *
+ * <b>Fixed:</b>
+ * - Fixed USB_GetHIDReportItemInfo() function modifying the given report item's data when the report item does not exist
+ * within the supplied report of a multiple report HID device
+ * - Fixed MassStorage based demos and projects resetting the SCSI sense values before the command is executed, leading to
+ * missed SCSI sense values when the host retrieves the sense key (thanks to Martin Degelsegger)
+ * - Fixed critical pipe/endpoint memory allocation issue where the bank memory address space could be silently overlapped
+ * in the USB controller if the endpoints or pipes were allocated in anything other than ascending order (thanks to Martin Degelsegger)
+ * - Fixed USBtoSerial and Benito project SetLineEncoding calls failing if the USART is busy, due to the RX ISR delaying the control
+ * request handler
+ * - Fixed LowLevel PrinterHost demo not sending control requests to the attached printer with the correct printer interface wIndex value
+ * - Added LEDs_ToggleLEDs() function to several board LED drivers which were missing it (thanks to Andrei Krainev)
+ * - Fixed SET FEATURE and CLEAR FEATURE control requests directed at an unconfigured endpoint causing request timeouts
+ * - Fixed incorrect signature reported in the CDC class bootloader for the ATMEGA32U2
+ * - Fixed USB_Host_ClearPipeStall() incorrectly determining the endpoint direction from the currently selected pipe
+ * - Fixed JTAG_DEBUG_POINT() and JTAG_DEBUG_BREAK() macros not compiling under pure C99 standards mode
+ * - Fixed endpoint selection within the CALLBACK_HID_Device_CreateHIDReport() callback function causing broken GET REPORT requests
+ * - Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target
+ * - Fixed BootloaderCDC project failing on some operating systems due to removed Line Encoding options (thanks to Alexey Belyaev)
+ * - Fixed incorrect LEDs_ChangeLEDs() function in the Benito board LED driver
+ * - Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set
+ * - Fixed broken FLASH/EEPROM programming in the AVRISP-MKII clone project when writing in non-paged mode and the polling byte cannot be used
+ * - Fixed SPI driver not explicitly setting /SS and MISO pins as inputs when SPI_Init() is called
+ * - Fixed ISR definition conflict in the XPLAIN bridge between the software UART and the AVRISP-MKII ISP modules
+ * - Fixed random enumeration failure while in device mode due to interrupts causing the Set Address request to exceed maximum timings
+ * - Fixed MIDI_Host_Flush() not aborting early when the specified MIDI host interface was not configured
+ * - Fixed MIDI class driver send routines silently discarding packets if the endpoint or pipe is busy (thanks to Robin Green)
+ *
+ * \section Sec_ChangeLog100807 Version 100807
+ * <b>New:</b>
* - Added new ADC_DisableChannel() function (thanks to Mich Davis)
* - Added new VTARGET_REF_VOLTS and VTARGET_SCALE_FACTOR compile time defines to the AVRISP-MKII programmer project to set
* the VTARGET reference voltage and scale factor
* - Added new Drivers/USB/LowLevel/Device.c file to house Device mode specific functions that are more complicated than simple macros
* - Added new AVRStudio 4 project files for all library demos, projects and bootloaders
* - Added ability to set the serial baud rate via the user's terminal in the XPLAINBridge project
+ * - Added new LUFA module variables for the different source modules in the core library makefile to simplify project makefiles
+ * - Added start of a new Test and Measurement class demo (thanks to Peter Lawrence)
+ * - Added new SPI_ORDER_* data order masks to the SPI peripheral driver
+ * - Added support to the AVRISP-MKII project for ISP speeds slower than 125KHz via a new software SPI driver
+ * - Added support for the new button/LED on the latest model USBTINY-MKII
*
* <b>Changed:</b>
* - The RingBuff library code has been replaced in the XPLAINBridge, Benito and USBtoSerial projects with an ultra lightweight
* - Rewrote the implementation of the SwapEndian_16() and SwapEndian_32() functions so that they compile down in most instances to
* minimal loads and stores rather than complicated shifts
* - The software UART in the XPLAINBridge has been largely altered to try to improve upon its performance and reliability
- * - The USBtoSerial project now flushes received data via a flush timer, so that several bytes can be transmitted at once
+ * - The USBtoSerial and Benito projects now flushes received data via a flush timer, so that several bytes can be transmitted at once
+ * - Removed the automated checking of event names in the demo, project and bootloader makefiles due to inconsistencies between the
+ * behaviour of the command line tools used to perform the check on each platform
+ * - Internal USB driver source files renamed and moved to ease future possible architecture ports
+ * - All internal pseudo-function macros have been converted to true inline functions for type-safety and readability
+ * - Changed LED indicator masks for the AVRISP-MKII project, so that there are defined roles for each LED
+ * - Altered the CDC Device and Host Class drivers' receive byte routines, so that no data is indicated by the function returning a
+ * negative value (thanks to Andreas Paulin)
+ * - Added auto flushing of OUT data to the CDC Host Class driver's USBTask function to automatically flush the send pipe buffer
*
* <b>Fixed:</b>
* - Fixed AVRISP project sending a LOAD EXTENDED ADDRESS command to 128KB AVRs after programming or reading from
* PDI and TPI programming modes infinitely
* - Fixed HID device class driver still using PrevReportINBuffer for GetReport control requests even when it has been
* set to NULL by the user application (thanks to Axel Rohde)
+ * - Fixed MIDI_Device_SendEventPacket() not correctly waiting for the endpoint to become ready (thanks to Robin Green)
+ * - Fixed Benito and USBtoSerial projects not turning off the USART before reconfiguring it, which could cause incorrect
+ * operation to occur (thanks to Bob Paddock)
+ * - Fixed Serial peripheral driver not turning off the USART before reconfiguring it, which would cause incorrect operation
+ * to occur (thanks to Bob Paddock)
+ * - Fixed software application start command broken in the DFU class bootloader when dfu-programmer is used due to application
+ * start address corruption
*
* \section Sec_ChangeLog100513 Version 100513
* <b>New:</b>
* read (thanks to Andrei Krainev)
* - Fixed device state not being reset back to the default state if the host sets the address to 0
* - Fixed Set Configuration requests not being stalled until the host has set the device's address
- * - Fixed Host mode HID class driver not sending the correct report type when HID_Host_SendReportByID() was called and the
+ * - Fixed Host mode HID class driver not sending the correct report type when HID_Host_SendReportByID() was called and the
* HID_HOST_BOOT_PROTOCOL_ONLY compile time option is set
* - Fixed INTERRUPT_CONTROL_ENDPOINT compile time option preventing other interrupts from occurring while the control endpoint
* request is being processed, causing possible lockups if a USB interrupt occurs during a transfer
*
* <b>Changed:</b>
* - Removed code in the Keyboard demos to send zeroed reports between two reports with differing numbers of key codes
- * as this relied on non-standard OS driver behavior to repeat key groups
+ * as this relied on non-standard OS driver behaviour to repeat key groups
* - The SCSI_Request_Sense_Response_t and SCSI_Inquiry_Response_t type defines are now part of the Mass Storage Class
* driver common defines, rather than being defined in the Host mode Class driver section only
* - The USB_MODE_HOST token is now defined even when host mode is not available
* - Fixed Mass Storage Host Class driver and Low Level demo not clearing the error condition if an attached device returns a
* STALL to a GET MAX LUN request (thanks to Martin Luxen)
* - Fixed TeensyHID bootloader not properly shutting down the USB interface to trigger a disconnection on the host before resetting
- * - Fixed MassStorageHost Class driver demo not having USB_STREAM_TIMEOUT_MS compile time option set properly to prevent slow
+ * - Fixed MassStorageHost Class driver demo not having USB_STREAM_TIMEOUT_MS compile time option set properly to prevent slow
* devices from timing out the data pipes
* - Fixed the definition of the Endpoint_BytesInEndpoint() macro for the U4 series AVR parts
* - Fixed MIDI host Class driver MIDI_Host_SendEventPacket() routine not properly checking for Pipe ready before writing
* - Added new Pipe_IsFrozen() macro to determine if the currently selected pipe is frozen
* - Added new USB_GetHIDReportSize() function to the HID report parser to retrieve the size of a given report by its ID
* - Added new combined Mass Storage and Keyboard demo (thanks to Matthias Hullin)
- *
+ *
* <b>Changed:</b>
* - SetIdle requests to the HID device driver with a 0 idle period (send changes only) now only affect the requested
* HID interface within the device, not all HID interfaces
* - Added new "Common" section to the class drivers, to hold all mode-independent definitions for clarity
* - Moved SCSI command/sense constants into the Mass Storage Class driver, instead of the user-code
* - Altered the SCSI commands in the LowLevel Mass Storage Host to save on FLASH space by reducing function calls
- * - Changed the parameters and behavior of the USB_GetDeviceConfigDescriptor() function so that it now performs size checks
+ * - Changed the parameters and behaviour of the USB_GetDeviceConfigDescriptor() function so that it now performs size checks
* and data validations internally, to simplify user code
* - Changed HIDParser to only zero out important values in the Parsed HID Report Item Information structure to save cycles
* - The HID report parser now always processed FEATURE items - HID_ENABLE_FEATURE_PROCESSING token now has no effect
* - Added new Pipe_BoundEndpointNumber() and Pipe_IsEndpointBound() functions
* - Added new DEVICE_STATE_AS_GPIOR and HOST_STATE_AS_GPIOR compile time options
* - Added 404 Not Found errors to the webserver in the RNDIS demos to indicate invalid URLs
- *
+ *
* <b>Changed:</b>
* - Deprecated pseudo-scheduler and removed dynamic memory allocator from the library (first no longer needed and second unused)
* - The device-mode CALLBACK_USB_GetDescriptor() function now has an extra parameter so that the memory space in which the requested
* internal control
* - Interrupts are no longer disabled during the processing of Control Requests on the default endpoint while in device mode
* - AudioOutput demos now always output to board LEDs, regardless of output mode (removed AUDIO_OUT_LEDS project option)
- * - Removed SINGLE_DEVICE_CONFIGURATION compile time option in favour of the new FIXED_NUM_CONFIGURATIONS option so that the exact number
+ * - Removed SINGLE_DEVICE_CONFIGURATION compile time option in favor of the new FIXED_NUM_CONFIGURATIONS option so that the exact number
* of device configurations can be defined statically
* - Removed VBUS events, as they are already exposed to the user application via the regular device connection and disconnection events
* - Renamed and altered existing events to properly separate out Host and Device mode events
+ * - All demos switched over from GNU99 standards mode to C99 standards mode, to reduce the dependancies on GCC-only language extensions
*
* <b>Fixed:</b>
* - Changed bootloaders to use FLASHEND rather than the existence of RAMPZ to determine if far FLASH pointers are needed to fix
* pipes can be used with the function
* - The USB Host management task now saves and restores the currently selected pipe before and after the task completes
* - Fixed GenericHIDHost demo report write routine incorrect for control type requests (thanks to Andrei Krainev)
- * - Removed Endpoint_ClearCurrentBank() and Pipe_ClearCurrentBank() in favour of new Endpoint_ClearIN(), Endpoint_ClearOUT(),
+ * - Removed Endpoint_ClearCurrentBank() and Pipe_ClearCurrentBank() in favor of new Endpoint_ClearIN(), Endpoint_ClearOUT(),
* Pipe_ClearIN() and Pipe_ClearOUT() macros (done to allow for the detection of packets of zero length)
* - Renamed *_ReadWriteAllowed() macros to *_IsReadWriteAllowed() to remain consistent with the rest of the LUFA API
* - Endpoint_IsSetupReceived() macro has been renamed to Endpoint_IsSETUPReceived(), Endpoint_ClearSetupReceived() macro has been
* - Changed over all deprecated GCC structure tag initializers to the standardized C99 format (thanks to Mike Alexander)
* - USB_HostRequest renamed to USB_ControlRequest, entire control request header is now read into USB_ControlRequest in Device mode
* rather than having the library pass only partially read header data to the application
- * - The USB_UnhandledControlPacket event has had its parameters removed, in favour of accessing the new USB_ControlRequest structure
+ * - The USB_UnhandledControlPacket event has had its parameters removed, in favor of accessing the new USB_ControlRequest structure
* - The Endpoint control stream functions now correctly send a ZLP to the host when less data than requested is sent
* - Fixed USB_RemoteWakeupEnabled flag never being set (the REMOTE WAKEUP Set Feature request was not being handled)
* - Renamed the FEATURELESS_CONTROL_ONLY_DEVICE compile-time token to CONTROL_ONLY_DEVICE
* - Changed HWB board driver to Buttons driver, to allow for the support of future boards with more than one mounted GPIO button
* - Serial driver now correctly calculates the baud register value when in double speed mode
* - Init function of the Serial driver is now static inline to product smaller code for the common-case of static init values
- *
+ *
*
* \section Sec_ChangeLog090401 Version 090401
*
* - Doxygen documentation now contains documentation on all the projects, bootloaders and most demos included with the library
* - CDC bootloader now runs user application when USB disconnected rather than waiting for a hard reset
* - MouseHostWithParser and KeyboardHostWithParser now support multiple-report devices
- * - RNDIS demo can now close connections correctly using the new TCP_APP_CLOSECONNECTION() macro - used in Webserver
+ * - RNDIS demo can now close connections correctly using the new TCP_APP_CLOSECONNECTION() macro - used in Webserver
* - Fixed the DFU bootloader, no longer freezes up when certain files are programmed into an AVR, made reading/writing faster
- * - Fixed mouse/joystick up/down movements reversed - HID mouse X/Y coordinates use a left-handed coordinate system, not a normal
+ * - Fixed mouse/joystick up/down movements reversed - HID mouse X/Y coordinates use a left-handed coordinate system, not a normal
* right-handed system
* - Added stub code to the CDC and USBtoSerial demos showing how to read and set the RS-232 handshake lines - not currently used in
* the demos, but the example code and supporting defines are now in place
* - All HID demos now pass the USB.org automated HID compliance tests
* - Polling interval of the interrupt endpoint in the CDC based demos changed to 0xFF to fix problems on Linux systems
* - Changed stream functions to accept a new callback function, with NO_STREAM_CALLBACKS used to disable all callbacks
- * - Mass Storage demo dataflash management routines changed to use the endpoint stream functions
+ * - Mass Storage demo dataflash management routines changed to use the endpoint stream functions
* - Added AVRStudio project files for each demo in addition to the existing Programmer's Notepad master project file
* - Re-added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes
* are reflected in the hardware (change was previously lost)
*
* - Fixed SwapEndian_32() function in Common.h so that it now works correctly (wrong parameter types)
* - Updated RNDIS demo - notification endpoint is no longer blocking so that it works with faulty Linux RNDIS
- * implementations (where the notification endpoint is ignored in favour of polling the control endpoint)
+ * implementations (where the notification endpoint is ignored in favor of polling the control endpoint)
* - Fixed incorrect Vendor Description string return size in RNDIS demo for the OID_GEN_VENDOR_DESCRIPTION OID token
* - Added very basic TCP/IP stack and HTTP/TELNET servers to RNDIS demo
* - Fixed DFU bootloader exit causing programming software to complain about failed writes
*
* - Added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes
* are reflected in the hardware
- * - Fixed CDC and USBtoSerial demos - Stream commands do not work for control endpoints, and the
+ * - Fixed CDC and USBtoSerial demos - Stream commands do not work for control endpoints, and the
* GetLineCoding request had an incorrect RequestType mask preventing it from being processed
* - Improved reliability of the USBtoSerial demo, adding a busy wait while the buffer is full
* - Device control endpoint size is now determined from the device's descriptors rather than being fixed
* - Separated out SPI code into new SPI driver in AT90USBXXX driver directory
* - Bootloader now returns correct PID for the selected USB AVR model, not just the AT90USB128X PID
* - Added support for the RZUSBSTICK board
- * - Bicolour driver removed in favour of generic LEDs driver
+ * - Bicolour driver removed in favor of generic LEDs driver
* - Added support for the ATMEGA32U4 AVR
* - Added MANUAL_PLL_CONTROL compile time option to prevent the USB library from manipulating the PLL
*
* - ID transition interrupt now raises the appropriate device/host disconnect event if device attached
* - Fixed double VBUS change (and VBUS -) event when detaching in device mode
* - Added ability to disable ANSI terminal codes by the defining of DISABLE_TERMINAL_CODES in makefile
- * - Removed return from ConfigurePipe and ConfigureEndpoint functions - use Pipe_IsConfigured() and
+ * - Removed return from ConfigurePipe and ConfigureEndpoint functions - use Pipe_IsConfigured() and
* Endpoint_IsConfigured() after calling the config functions to determine success
*/
+
projects / pub / lufa.git / blobdiff