* <td>AUX_LINE_PORT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>PORT register for the programmer's AUX target line. The use of this line varies between the programming protocols,
- * but is generally used for the target's /RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * but is generally used for the target's /RESET line.
+ * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>AUX_LINE_PIN</td>
* <td>Makefile LUFA_OPTS</td>
* <td>PIN register for the programmer's AUX target line. The use of this line varies between the programming protocols,
- * but is generally used for the target's /RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * but is generally used for the target's /RESET line.
+ * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>AUX_LINE_DDR</td>
* <td>Makefile LUFA_OPTS</td>
* <td>DDR register for the programmer's AUX target line. The use of this line varies between the programming protocols,
- * but is generally used for the target's /RESET line. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * but is generally used for the target's /RESET line.
+ * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>AUX_LINE_MASK</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Mask for the programmer's AUX target line. The use of this line varies between the programming protocols,
- * but is generally used for the target's /RESET line. <b>Must not be the AVR's /SS pin</b>. <i>Ignored when
- * compiled for the XPLAIN board.</i></td>
+ * but is generally used for the target's /RESET line. <b>Must not be the AVR's /SS pin</b>.
+ * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>VTARGET_ADC_CHANNEL</td>
* <td>Makefile LUFA_OPTS</td>
* <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined.
- * <i>Ignored when compiled for targets lacking an ADC.</i></td>
+ * \n \n <i>Ignored when compiled for targets lacking an ADC.</i></td>
* </tr>
* <tr>
* <td>ENABLE_ISP_PROTOCOL</td>
* <td>Makefile LUFA_OPTS</td>
- * <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * <td>Define to enable SPI programming protocol support.
+ * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>ENABLE_XPROG_PROTOCOL</td>
* <td>Makefile LUFA_OPTS</td>
- * <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * <td>Define to enable PDI and TPI programming protocol support.
+ * \n \n <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>NO_VTARGET_DETECT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer
- * to report a fixed 3.3V target voltage to the host regardless of the real target voltage. <i>Ignored when compiled for
- * targets lacking an ADC.</i></td>
+ * to report a fixed 3.3V target voltage to the host regardless of the real target voltage.
+ * \n \n <i>Ignored when compiled for targets lacking an ADC.</i></td>
* </tr>
* <tr>
* <td>VTARGET_REF_VOLTS</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply
* voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage
- * to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
+ * to the ADC.
+ * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
* </tr>
* <tr>
* <td>VTARGET_USE_INTERNAL_REF</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Selects the internal 2.56V ADC reference voltage, instead of using the AVR's VREF pin. When enabled, this option will
- * override the VTARGET_REF_VOLTS configuration option. <i>Ignored when compiled for targets lacking an ADC, or when
- * NO_VTARGET_DETECT is defined.</i></td>
+ * override the VTARGET_REF_VOLTS configuration option.
+ * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
* </tr>
* <tr>
* <td>VTARGET_SCALE_FACTOR</td>
* <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the
* ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be
* measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set
- * to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
+ * to 2.
+ * \n \n <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
* </tr>
* <tr>
* <td>LIBUSB_DRIVER_COMPAT</td>
* <td>XCK_RESCUE_CLOCK_ENABLE</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to move the ISP rescue clock to the AVR's XCK pin instead of the OCR1A output pin. This is useful for existing programming
- * hardware that does not expose the OCR1A pin of the AVR, but *may* cause some issues with PDI programming mode.</td>
+ * hardware that does not expose the OCR1A pin of the AVR, but <i>may</i> cause some issues with PDI programming mode.</td>
* </tr>
* <tr>
* <td>INVERTED_ISP_MISO</td>
* </tr>
* <tr>
* <td>FIRMWARE_VERSION_MINOR</td>
+ * <td>Makefile LUFA_OPTS</td>
* <td>Define to set the minor firmware revision nunber reported to the host on request. By default this will use a firmware version compatible
* with the latest Atmel IDE version, however if desired the reported minor value can be adjusted here.</td>
* </tr>
projects / pub / lufa.git / blobdiff