* which is not always accurate (host may suspend the bus while still connected). If the actual connection state\r
* needs to be determined, VBUS should be routed to an external pin, and the auto-detect behaviour turned off by\r
* passing the NO_LIMITED_CONTROLLER_CONNECT token to the compiler via the -D switch at compile time. The connection\r
- * and disconnection events may be manually fired by \ref RAISE_EVENT(), and the \ref USB_IsConnected global changed manually.\r
+ * and disconnection events may be manually fired, and the \ref USB_IsConnected global changed manually.\r
*\r
* \ingroup Group_USBManagement\r
*/\r
extern volatile bool USB_IsInitialized;\r
\r
/** Structure containing the last received Control request when in Device mode (for use in user-applications\r
- * inside of the \ref USB_UnhandledControlPacket() event, or for filling up with a control request to issue when\r
+ * inside of the \ref EVENT_USB_UnhandledControlPacket() event, or for filling up with a control request to issue when\r
* in Host mode before calling \ref USB_Host_SendControlRequest().\r
*\r
* \ingroup Group_USBManagement\r
extern volatile uint8_t USB_HostState;\r
#endif\r
\r
- /* Throwable Events: */\r
- #if defined(USB_CAN_BE_HOST) || defined(__DOXYGEN__)\r
- /** This module raises the \ref USB_Connect event when a USB device has been connected whilst in host\r
- * mode, but not yet enumerated.\r
- *\r
- * \see \ref Group_Events for more information on this event.\r
- */\r
- RAISES_EVENT(USB_Connect);\r
-\r
- /** This module raises the \ref USB_DeviceAttached event when in host mode, and a device is attached\r
- * to the AVR's USB interface.\r
- *\r
- * \see \ref Group_Events for more information on this event.\r
- */\r
- RAISES_EVENT(USB_DeviceAttached);\r
-\r
- /** This module raises the \ref USB_DeviceUnattached event when in host mode, and a device is removed\r
- * from the AVR's USB interface.\r
- *\r
- * \see \ref Group_Events for more information on this event.\r
- */\r
- RAISES_EVENT(USB_DeviceUnattached);\r
- \r
- /** This module raises the \ref USB_DeviceEnumerationFailed event when in host mode, and an\r
- * attached USB device has failed to successfully enumerated.\r
- *\r
- * \see \ref Group_Events for more information on this event.\r
- */\r
- RAISES_EVENT(USB_DeviceEnumerationFailed);\r
-\r
- /** This module raises the \ref USB_DeviceEnumerationComplete event when in host mode, and an\r
- * attached USB device has been successfully enumerated and ready to be used by the user\r
- * application.\r
- *\r
- * \see \ref Group_Events for more information on this event.\r
- */\r
- RAISES_EVENT(USB_DeviceEnumerationComplete);\r
-\r
- /** This module raises the \ref USB_Disconnect event when an attached USB device is removed from the USB\r
- * bus.\r
- *\r
- * \see \ref Group_Events for more information on this event.\r
- */\r
- RAISES_EVENT(USB_Disconnect);\r
- #endif\r
-\r
/* Tasks: */\r
/** This is the main USB management task. The USB driver requires that this task be executed\r
* continuously when the USB system is active (device attached in host mode, or attached to a host\r
* The USB task must be serviced within 50mS in all modes, when needed. The task may be serviced \r
* at all times, or (for minimum CPU consumption):\r
*\r
- * - In device mode, it may be disabled at start-up, enabled on the firing of the \ref USB_Connect event\r
- * and disabled again on the firing of the \ref USB_Disconnect event.\r
+ * - In device mode, it may be disabled at start-up, enabled on the firing of the \ref EVENT_USB_Connect() event\r
+ * and disabled again on the firing of the \ref EVENT_USB_Disconnect() event.\r
*\r
- * - In host mode, it may be disabled at start-up, enabled on the firing of the \ref USB_DeviceAttached\r
- * event and disabled again on the firing of the \ref USB_DeviceUnattached event.\r
+ * - In host mode, it may be disabled at start-up, enabled on the firing of the \ref EVENT_USB_DeviceAttached()\r
+ * event and disabled again on the firing of the \ref EVENT_USB_DeviceUnattached() event.\r
*\r
* If in device mode (only), the control endpoint can instead be managed via interrupts entirely by the library\r
* by defining the INTERRUPT_CONTROL_ENDPOINT token and passing it to the compiler via the -D switch.\r
projects / pub / lufa.git / blobdiff