* \section Sec_ChangeLogXXXXXX Version XXXXXX\r
*\r
* <b>New:</b>\r
+ * - Added incomplete MIDIToneGenerator project\r
+ * - Added new Relay Controller Board project (thanks to OBinou)\r
+ * - Added board hardware driver support for the Teensy, USBTINY MKII, Benito and JM-DB-U2 lines of third party USB AVR boards\r
+ *\r
+ * <b>Changed:</b>\r
+ * - AVRISP programmer project now has a more robust timeout system, allowing for an increase of the software USART speed\r
+ * for PDI and TPI programming\r
+ * - Added a timeout value to the TWI_StartTransmission() function, within which the addressed device must respond\r
+ * - Webserver project now uses the board LEDs to indicate the current IP configuration state\r
+ * - Added ENABLE_TELNET_SERVER compile time option to the Webserver project to disable the TELNET server if desired\r
+ * - Increased throughput of the USBtoSerial demo on systems that send multiple bytes per packet (thanks to Opendous Inc.)\r
+ * - Double bank CDC endpoints in the XPLAIN Bridge project, re-enable JTAG once the mode selection pin has been sampled.\r
+ * - Standardized the naming scheme given to configuration descriptor sub-elements in the Device mode demos, bootloaders\r
+ * and projects\r
+ * - All Class Driver Host mode demos now correctly set the board LEDs to READY once the enumeration process has completed\r
+ * - Added LIBUSB_FILTERDRV_COMPAT compile time option to the AVRISP programmer project to make the code compatible with Windows\r
+ * builds of avrdude at the expense of AVRStudio compatibility\r
+ *\r
+ * <b>Fixed:</b>\r
+ * - Fixed software PDI/TPI programming mode in the AVRISP project not correctly toggling just the clock pin\r
+ * - Fixed TWI_StartTransmission() corrupting the contents of the GPIOR0 register\r
+ * - Fixed TWI driver not aborting when faced with no response after attempting to address a device on the bus\r
+ * - Fixed ADC routines not correctly returning the last result when multiple channels were read\r
+ * - Fixed ADC routines failing to read the extended channels (Channels 8 to 13, Internal Temperature Sensor) on the\r
+ * U4 series USB AVR parts\r
+ * - Fixed LowLevel MassStorage demo broken on the U2 series USB AVRs due to unsupported double-banked endpoint modes used\r
+ * - Fixed compilation error in the AudioInput demos when MICROPHONE_BIASED_TO_HALF_RAIL is defined (thanks to C. Scott Ananian)\r
+ * - Fixed incorrect definition of HID_ALIGN_DATA() causing incorrect HID report item data alignment\r
+ * - Fixed Still Image Host class driver not resetting the transaction ID when a new session is opened, fixed driver not sending\r
+ * a valid session ID to the device\r
+ *\r
+ * \section Sec_ChangeLog100219 Version 100219\r
+ *\r
+ * <b>New:</b>\r
* - Added TPI programming support for 6-pin ATTINY devices to the AVRISP programmer project (thanks to Tom Light)\r
* - Added command timeout counter to the AVRISP project so that the device no longer freezes when incorrectly connected\r
* to a target\r
* - Added ADC MUX masks for the standard ADC input channels on all AVR models with an ADC, altered demos to use these masks\r
* as on some models, the channel number is not identical to its single-ended ADC MUX mask\r
* - New Webserver project, a RNDIS host USB webserver using the open source uIP TCP/IP network stack and FatFS library\r
+ * - New BOARD value option BOARD_NONE (equivelent to not specifying BOARD) which will remove all board hardware drivers which\r
+ * do not adversely affect the code operation (currently only the LEDs driver)\r
+ * - Added keyboard modifier masks (HID_KEYBOARD_MODIFER_*) and LED report masks (KEYBOARD_LED_*) to the HID class driver and\r
+ * Keyboard demos\r
+ * - Added .5MHz recovery clock to the AVRISP programmer project when in ISP programming mode to correct mis-set fuses\r
*\r
* <b>Changed:</b>\r
* - Slowed down software USART carried PDI programming in the AVRISP project to prevent transmission errors\r
* - Fixed CDC and RNDIS host demos and class drivers - bidirectional endpoints should use two seperate pipes, not one half-duplex pipe\r
* - Fixed Pipe_IsEndpointBound() not taking the endpoint's direction into account\r
* - Fixed EEPROM and FLASH ISP programming in the AVRISP project\r
+ * - Fixed incorrect values of USB_CONFIG_ATTR_SELFPOWERED and USB_CONFIG_ATTR_REMOTEWAKEUP tokens (thanks to Claus Christensen)\r
+ * - Fixed SerialStream driver blocking while waiting for characters to be received instead of returning EOF\r
+ * - Fixed SerialStream driver not setting stdin to the created serial stream (thanks to Mike Alexander)\r
+ * - Fixed USB_GetHIDReportSize() returning the number of bits in the specified report instead of bytes\r
+ * - Fixed AVRISP project not extending the command delay after each successful page/word/byte program\r
+ * - Fixed accuracy of the SERIAL_UBBRVAL() and SERIAL_2X_UBBRVAL() macros for higher baudrates (thanks to Renaud Cerrato)\r
*\r
* \section Sec_ChangeLog091223 Version 091223\r
*\r
* - Fixed Still Image Host Class driver truncating the PIMA response code (thanks to Daniel Seibert)\r
* - Fixed USB_CurrentMode not being reset to USB_MODE_NONE when the USB interface is shut down and both Host and Device modes can be\r
* used (thanks to Daniel Levy)\r
- * - Fixed TeensyHID bootloader not enumerating to the host correctly\r
+ * - Fixed TeensyHID bootloader not enumerating to the host correctly (thanks to Clint Fisher)\r
* - Fixed AVRISP project timeouts not checking for the correct timeout period (thanks to Carl Ott)\r
* - Fixed STK525 Dataflash driver using incorrect bit-shifting for Dataflash addresses (thanks to Tim Mitchell)\r
*\r
projects / pub / lufa.git / blobdiff