X-Git-Url: http://git.linex4red.de/pub/USBaspLoader.git/blobdiff_plain/fdd80449610db4cccc152e17b04cdb51de578a61..4c96f1315e9f6c7560c6aead20b393e4c55c778f:/firmware/bootloaderconfig.h

diff --git a/firmware/bootloaderconfig.h b/firmware/bootloaderconfig.h
index 9ca2cd1..9eb07c9 100644
--- a/firmware/bootloaderconfig.h
+++ b/firmware/bootloaderconfig.h
@@ -322,6 +322,72 @@ these macros are defined, the boot loader usees them.
  * user intervention
  */
 
+#ifdef CONFIG_NO__BOOTLOADER_HIDDENEXITCOMMAND
+#	define HAVE_BOOTLOADER_HIDDENEXITCOMMAND 0
+#else
+#	define HAVE_BOOTLOADER_HIDDENEXITCOMMAND 0xff
+#endif
+/* 
+ * When enabling "BOOTLOADER_HIDDENEXITCOMMAND", then
+ * sending the RAW-ISP command "0xff 0xXX 0xXX 0xXX"
+ * will cause the bootloader to start the firmware
+ * as soon as the programming software disconnects.
+ */
+
+#ifdef CONFIG_BOOTLOADER_LOOPCYCLES_TIMEOUT
+#	define BOOTLOADER_LOOPCYCLES_TIMEOUT	(CONFIG_BOOTLOADER_LOOPCYCLES_TIMEOUT)
+#else 
+#	define BOOTLOADER_LOOPCYCLES_TIMEOUT	(0)
+#endif
+/* 
+ * When greater than "0", "BOOTLOADER_LOOPCYCLES_TIMEOUT"
+ * defines how many 16bit loopcycles can be cycled,
+ * before bootloader times out and starts user
+ * firmware.
+ * Of course "BOOTLOADER_CAN_EXIT" must be enabled.
+ * If value is even too small, bootloader  will not
+ * exit as long as bootLoaderConditionSimple stays on.
+ */
+
+#ifdef CONFIG_HAVE__BOOTLOADER_ABORTTIMEOUTONACT
+#endif
+/*
+ * When defined, the bootloader will abort the timeout when
+ * it sees some activity (bootLoaderConditionSimple() or
+ * programming). 
+ * After aborting timeout, the bootloader falls back to
+ * conventional exitting.
+ */
+
+#ifdef CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE
+#endif
+/*
+ * Ignore bootLoaderCondition() (BUT NOT bootLoaderConditionSimple())
+ * and always enter the program-mode.
+ * This is helpful to emulate behaviour of Arduino bootloaders
+ */
+
+#ifdef CONFIG_HAVE__BOOTLOADER_IGNOREPROGBUTTON
+#	if ( (defined(CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE)) && (defined(BOOTLOADER_CAN_EXIT)) && (BOOTLOADER_LOOPCYCLES_TIMEOUT >= 8) )
+#		define BOOTLOADER_IGNOREPROGBUTTON	1
+#	else
+#		define BOOTLOADER_IGNOREPROGBUTTON	0
+#	endif
+#endif
+/*
+ * Generates an USBaspLoader without using the PROGBUTTON.
+ * It can be used to reduce the required PINcount for USBaspLoader
+ * on the MCU.
+ * However this feature is very dangerous, so it becomes only
+ * enabled, if "CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE" is
+ * enabled and "CONFIG_NO__BOOTLOADER_CAN_EXIT" is disabled, too.
+ * Additionally "BOOTLOADER_LOOPCYCLES_TIMEOUT" must be greater 
+ * or equal than 8 (In order to give user enough time to program).
+ * 
+ * When active, "JUMPER_PORT" and "JUMPER_BIT" are ignored and
+ * can be soldered otherwise.
+ */
+
 //#define SIGNATURE_BYTES             0x1e, 0x93, 0x07, 0     /* ATMega8 */
 /* This macro defines the signature bytes returned by the emulated USBasp to
  * the programmer software. They should match the actual device at least in
@@ -352,23 +418,31 @@ these macros are defined, the boot loader usees them.
 
 static inline void  bootLoaderInit(void)
 {
+#if (BOOTLOADER_IGNOREPROGBUTTON)
+#else
     PIN_DDR(JUMPER_PORT)  = 0;
     PIN_PORT(JUMPER_PORT) = (1<< PIN(JUMPER_PORT, JUMPER_BIT)); /* activate pull-up */
+#endif
 
 //     deactivated by Stephan - reset after each avrdude op is annoing!
 //     if(!(MCUCSR & (1 << EXTRF)))    /* If this was not an external reset, ignore */
 //         leaveBootloader();
-
-    MCUCSR = 0;                     /* clear all reset flags for next time */
 }
 
 static inline void  bootLoaderExit(void)
 {
+#if (BOOTLOADER_IGNOREPROGBUTTON)
+#else
     PIN_PORT(JUMPER_PORT) = 0;		/* undo bootLoaderInit() changes */
+#endif
 }
 
 
-#define bootLoaderConditionSimple()	((PIN_PIN(JUMPER_PORT) & (1 << PIN(JUMPER_PORT, JUMPER_BIT))) == 0)
+#if (BOOTLOADER_IGNOREPROGBUTTON)
+#	define bootLoaderConditionSimple()	(false)
+#else
+#	define bootLoaderConditionSimple()	((PIN_PIN(JUMPER_PORT) & (1 << PIN(JUMPER_PORT, JUMPER_BIT))) == 0)
+#endif
 
 #if (HAVE_BOOTLOADERENTRY_FROMSOFTWARE)
 /*
@@ -389,9 +463,13 @@ static inline void  bootLoaderExit(void)
 static volatile uint8_t __BOOTLOADERENTRY_FROMSOFTWARE__bootup_RAMEND_doesmatch __attribute__ ((section(".noinit")));
 static volatile uint8_t __BOOTLOADERENTRY_FROMSOFTWARE__bootup_MCUCSR __attribute__ ((section(".noinit")));
 
+#	ifdef CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE
+#		define bootLoaderCondition()	(true)
+#	else
 static inline bool bootLoaderCondition(void)
 {
-  if (__BOOTLOADERENTRY_FROMSOFTWARE__bootup_MCUCSR & (_BV(WDRF))) {
+  if (__BOOTLOADERENTRY_FROMSOFTWARE__bootup_MCUCSR & (~(_BV(WDRF)))) {
+  } else {
     if (__BOOTLOADERENTRY_FROMSOFTWARE__bootup_RAMEND_doesmatch == (__BOOTLOADERENTRY_FROMSOFTWARE__EXPECTEDADDRESS & 0xff)) {
       // anything else: match - the firmware is calling the bootloader
       return true;
@@ -399,8 +477,13 @@ static inline bool bootLoaderCondition(void)
   }
   return bootLoaderConditionSimple();
 }
+#	endif
 #else
-#define bootLoaderCondition		bootLoaderConditionSimple
+#	ifdef CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE
+#		define bootLoaderCondition()	(true)
+#	else
+#		define bootLoaderCondition	bootLoaderConditionSimple
+#	endif
 #endif
 
 #endif /* __ASSEMBLER__ */