ATmega2560 passed extensive testing (20MHz)

[pub/USBaspLoader.git] / firmware / bootloaderconfig.h

diff --git a/firmware/bootloaderconfig.h b/firmware/bootloaderconfig.h
index 005d9bb..531ba97 100644 (file)
--- a/firmware/bootloaderconfig.h
+++ b/firmware/bootloaderconfig.h
@@ -3,11 +3,10 @@
  * Author: Christian Starkjohann
  * Author: Stephan Baerwolf
  * Creation Date: 2007-12-08
  * Author: Christian Starkjohann
  * Author: Stephan Baerwolf
  * Creation Date: 2007-12-08

- * Modification Date: 2012-11-10
+ * Modification Date: 2013-03-31

  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt)
  * Tabsize: 4
  * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt)

- * This Revision: $Id: bootloaderconfig.h 729 2009-03-20 09:03:58Z cs $

  */
 
 #ifndef __bootloaderconfig_h_included__
  */
 
 #ifndef __bootloaderconfig_h_included__


@@ -57,14 +56,28 @@ these macros are defined, the boot loader usees them.
 /* This is the port where the USB bus is connected. When you configure it to
  * "B", the registers PORTB, PINB and DDRB will be used.
  */
 /* This is the port where the USB bus is connected. When you configure it to
  * "B", the registers PORTB, PINB and DDRB will be used.
  */

+#ifndef USB_CFG_INTPORT_BIT
+  #if (defined(__AVR_ATmega640__) || defined(__AVR_ATmega1280__) || defined(__AVR_ATmega1281__) || defined(__AVR_ATmega2560__) || defined(__AVR_ATmega2561__))
+    #define USB_CFG_INTPORT_BIT 0
+  #else
+    #define USB_CFG_INTPORT_BIT 2
+  #endif
+#endif
+/* Not all devices have their INT0 on PD2.
+ * Since "INT0" and "USB_CFG_DPLUS_BIT" should get the same signals,
+ * map them to be ideally the same:
+ * So abstract "USB_CFG_DPLUS_BIT" to this one here.
+ */
+

 #ifndef USB_CFG_DMINUS_BIT
 #ifndef USB_CFG_DMINUS_BIT

-  #define USB_CFG_DMINUS_BIT      6    /* old value was 4 */
+  /* This is Revision 3 and later (where PD6 and PD7 were swapped */
+  #define USB_CFG_DMINUS_BIT      7    /* Rev.2 and previous was 6 */

 #endif
 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
  * This may be any bit in the port.
  */
 #ifndef USB_CFG_DPLUS_BIT
 #endif
 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
  * This may be any bit in the port.
  */
 #ifndef USB_CFG_DPLUS_BIT

-  #define USB_CFG_DPLUS_BIT       2
+  #define USB_CFG_DPLUS_BIT       USB_CFG_INTPORT_BIT

 #endif
 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
  * This may be any bit in the port. Please note that D+ must also be connected
 #endif
 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
  * This may be any bit in the port. Please note that D+ must also be connected


@@ -77,7 +90,8 @@ these macros are defined, the boot loader usees them.
  * jumper is connected to this port
  */
 #ifndef JUMPER_BIT
  * jumper is connected to this port
  */
 #ifndef JUMPER_BIT

-  #define JUMPER_BIT           7       /* old value was 0 */
+  /* This is Revision 3 and later (where PD6 and PD7 were swapped */
+  #define JUMPER_BIT           6       /* Rev.2 and previous was 7 */

 #endif
 /* 
  * jumper is connected to this bit in port "JUMPER_PORT", active low
 #endif
 /* 
  * jumper is connected to this bit in port "JUMPER_PORT", active low


@@ -275,6 +289,29 @@ these macros are defined, the boot loader usees them.
  * instead the right content of the flash memory.
  */
 
  * instead the right content of the flash memory.
  */
 

+#ifdef CONFIG_USE__EXCESSIVE_ASSEMBLER
+#      define USE_EXCESSIVE_ASSEMBLER          1
+#else
+#      define USE_EXCESSIVE_ASSEMBLER          0
+#endif
+/* This macro enables large codeareas of hand-optimized assembler code.
+ * WARNING:
+ * It will only work properly on devices with <64k of flash memory and SRAM.
+ * Some configuration macros (when changed) may not be applied correctly
+ * (since their behaviour is raced within asm)!
+ * Nevertheless this feature saves lots of memory.
+ */
+
+#ifdef CONFIG_USE__BOOTUP_CLEARRAM
+#      define USE_BOOTUP_CLEARRAM              1
+#else
+#      define USE_BOOTUP_CLEARRAM              0
+#endif
+/* This macro enables some (init3) code, executed at bootup.
+ * This codefragment will safely overwrite the whole SRAM with "0"
+ * (except registers and IO), since RESET will NOT clear old RAM content.
+ */
+

 //#define SIGNATURE_BYTES             0x1e, 0x93, 0x07, 0     /* ATMega8 */
 /* This macro defines the signature bytes returned by the emulated USBasp to
  * the programmer software. They should match the actual device at least in
 //#define SIGNATURE_BYTES             0x1e, 0x93, 0x07, 0     /* ATMega8 */
 /* This macro defines the signature bytes returned by the emulated USBasp to
  * the programmer software. They should match the actual device at least in


@@ -299,6 +336,10 @@ these macros are defined, the boot loader usees them.
 #   define MCUCSR   MCUSR
 #endif
 
 #   define MCUCSR   MCUSR
 #endif
 

+/* WARNING:
+ * following commands and macros may not be evaluated properly when 'USE_EXCESSIVE_ASSEMBLER"
+ */
+

 static inline void  bootLoaderInit(void)
 {
     PIN_DDR(JUMPER_PORT)  = 0;
 static inline void  bootLoaderInit(void)
 {
     PIN_DDR(JUMPER_PORT)  = 0;