fix: rename BOOTLOADER_LOOPCYCLES_TIMEOUT

[pub/USBaspLoader.git] / firmware / bootloaderconfig.h

diff --git a/firmware/bootloaderconfig.h b/firmware/bootloaderconfig.h
index f469f8d..9eb07c9 100644 (file)
--- a/firmware/bootloaderconfig.h
+++ b/firmware/bootloaderconfig.h
@@ -334,8 +334,10 @@ these macros are defined, the boot loader usees them.
  * as soon as the programming software disconnects.
  */
 
-#ifndef BOOTLOADER_LOOPCYCLES_TIMEOUT
-#      define BOOTLOADER_LOOPCYCLES_TIMEOUT    0
+#ifdef CONFIG_BOOTLOADER_LOOPCYCLES_TIMEOUT
+#      define BOOTLOADER_LOOPCYCLES_TIMEOUT    (CONFIG_BOOTLOADER_LOOPCYCLES_TIMEOUT)
+#else 
+#      define BOOTLOADER_LOOPCYCLES_TIMEOUT    (0)
 #endif
 /* 
  * When greater than "0", "BOOTLOADER_LOOPCYCLES_TIMEOUT"
@@ -365,6 +367,27 @@ these macros are defined, the boot loader usees them.
  * This is helpful to emulate behaviour of Arduino bootloaders
  */
 
+#ifdef CONFIG_HAVE__BOOTLOADER_IGNOREPROGBUTTON
+#      if ( (defined(CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE)) && (defined(BOOTLOADER_CAN_EXIT)) && (BOOTLOADER_LOOPCYCLES_TIMEOUT >= 8) )
+#              define BOOTLOADER_IGNOREPROGBUTTON      1
+#      else
+#              define BOOTLOADER_IGNOREPROGBUTTON      0
+#      endif
+#endif
+/*
+ * Generates an USBaspLoader without using the PROGBUTTON.
+ * It can be used to reduce the required PINcount for USBaspLoader
+ * on the MCU.
+ * However this feature is very dangerous, so it becomes only
+ * enabled, if "CONFIG_HAVE__BOOTLOADER_ALWAYSENTERPROGRAMMODE" is
+ * enabled and "CONFIG_NO__BOOTLOADER_CAN_EXIT" is disabled, too.
+ * Additionally "BOOTLOADER_LOOPCYCLES_TIMEOUT" must be greater 
+ * or equal than 8 (In order to give user enough time to program).
+ * 
+ * When active, "JUMPER_PORT" and "JUMPER_BIT" are ignored and
+ * can be soldered otherwise.
+ */
+
 //#define SIGNATURE_BYTES             0x1e, 0x93, 0x07, 0     /* ATMega8 */
 /* This macro defines the signature bytes returned by the emulated USBasp to
  * the programmer software. They should match the actual device at least in
@@ -395,8 +418,11 @@ these macros are defined, the boot loader usees them.
 
 static inline void  bootLoaderInit(void)
 {
+#if (BOOTLOADER_IGNOREPROGBUTTON)
+#else
     PIN_DDR(JUMPER_PORT)  = 0;
     PIN_PORT(JUMPER_PORT) = (1<< PIN(JUMPER_PORT, JUMPER_BIT)); /* activate pull-up */
+#endif
 
 //     deactivated by Stephan - reset after each avrdude op is annoing!
 //     if(!(MCUCSR & (1 << EXTRF)))    /* If this was not an external reset, ignore */
@@ -405,11 +431,18 @@ static inline void  bootLoaderInit(void)
 
 static inline void  bootLoaderExit(void)
 {
+#if (BOOTLOADER_IGNOREPROGBUTTON)
+#else
     PIN_PORT(JUMPER_PORT) = 0;         /* undo bootLoaderInit() changes */
+#endif
 }
 
 
-#define bootLoaderConditionSimple()    ((PIN_PIN(JUMPER_PORT) & (1 << PIN(JUMPER_PORT, JUMPER_BIT))) == 0)
+#if (BOOTLOADER_IGNOREPROGBUTTON)
+#      define bootLoaderConditionSimple()      (false)
+#else
+#      define bootLoaderConditionSimple()      ((PIN_PIN(JUMPER_PORT) & (1 << PIN(JUMPER_PORT, JUMPER_BIT))) == 0)
+#endif
 
 #if (HAVE_BOOTLOADERENTRY_FROMSOFTWARE)
 /*