fix environmental and configuration issues within Makefile.inc

[pub/USBaspLoader.git] / firmware / bootloaderconfig.h

diff --git a/firmware/bootloaderconfig.h b/firmware/bootloaderconfig.h
index aa234a1..97311dd 100644 (file)
--- a/firmware/bootloaderconfig.h
+++ b/firmware/bootloaderconfig.h
@@ -42,7 +42,11 @@ these macros are defined, the boot loader usees them.
 /* This is the port where the USB bus is connected. When you configure it to
  * "B", the registers PORTB, PINB and DDRB will be used.
  */
-#define USB_CFG_DMINUS_BIT      4
+#define JUMPER_BIT             7       /* old value was 0 */
+/* 
+ * jumper is connected to this bit in port D, active low
+ */
+#define USB_CFG_DMINUS_BIT      6      /* old value was 4 */
 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
  * This may be any bit in the port.
  */
@@ -77,6 +81,29 @@ these macros are defined, the boot loader usees them.
 /* ---------------------- feature / code size options ---------------------- */
 /* ------------------------------------------------------------------------- */
 
+#define HAVE_READ_LOCK_FUSE        1
+/*
+ * enable the loaders capability to load its lfuse, hfuse and lockbits
+ * ...However, programming of these is prohibited...
+ */
+
+#define HAVE_BLB11_SOFTW_LOCKBIT    1
+/*
+ * The IC itself do not need to prgra BLB11, but the bootloader will avaoid 
+ * to erase itself from the bootregion
+ */
+
+#define HAVE_SPMINTEREFACE         1
+/*
+ * Since code within normal section of application memory (rww-section) is
+ * not able to call spm for programming flash-pages, this option (when
+ * enabled) will insert a small subroutine into the bootloader-section
+ * to enable applications to circumvent this limitation and make them
+ * able to program the flash in a similar way as the bootloader does, too.
+ * For further details see "spminterface.h", which implements this 
+ * feature.
+ */
+
 #define HAVE_EEPROM_PAGED_ACCESS    1
 /* If HAVE_EEPROM_PAGED_ACCESS is defined to 1, page mode access to EEPROM is
  * compiled in. Whether page mode or byte mode access is used by AVRDUDE
@@ -90,7 +117,7 @@ these macros are defined, the boot loader usees them.
  * signature) does not support page mode for EEPROM. It is required for
  * accessing the EEPROM on the ATMega8. Costs ~54 bytes.
  */
-#define BOOTLOADER_CAN_EXIT         1
+#define BOOTLOADER_CAN_EXIT         0
 /* If this macro is defined to 1, the boot loader will exit shortly after the
  * programmer closes the connection to the device. Costs ~36 bytes.
  */
@@ -132,17 +159,17 @@ these macros are defined, the boot loader usees them.
 
 #ifndef __ASSEMBLER__   /* assembler cannot parse function definitions */
 
-#define JUMPER_BIT  7   /* jumper is connected to this bit in port D, active low */
-
 #ifndef MCUCSR          /* compatibility between ATMega8 and ATMega88 */
 #   define MCUCSR   MCUSR
 #endif
 
 static inline void  bootLoaderInit(void)
 {
-    PORTD |= (1 << JUMPER_BIT);     /* activate pull-up */
-    if(!(MCUCSR & (1 << EXTRF)))    /* If this was not an external reset, ignore */
-        leaveBootloader();
+    DDRD   = 0;
+    PORTD  = (1 << JUMPER_BIT);     /* activate pull-up */
+//     deactivated by Stephan - reset after each avrdude op is annoing!
+//     if(!(MCUCSR & (1 << EXTRF)))    /* If this was not an external reset, ignore */
+//         leaveBootloader();
     MCUCSR = 0;                     /* clear all reset flags for next time */
 }
 
@@ -151,7 +178,7 @@ static inline void  bootLoaderExit(void)
     PORTD = 0;                      /* undo bootLoaderInit() changes */
 }
 
-#define bootLoaderCondition()   ((PIND & (1 << JUMPER_BIT)) == 0)
+#define bootLoaderCondition()          ((PIND & (1 << JUMPER_BIT)) == 0)
 
 #endif /* __ASSEMBLER__ */