X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/f13bc35a199f3840aaaabecf5f8616f20da7c262..67bc62510942eb83dd9c4ab323ed09d83764bf4b:/Projects/AVRISP-MKII/AVRISP.txt

diff --git a/Projects/AVRISP-MKII/AVRISP.txt b/Projects/AVRISP-MKII/AVRISP.txt
index 9a9b1b04b..de08d5f37 100644
--- a/Projects/AVRISP-MKII/AVRISP.txt
+++ b/Projects/AVRISP-MKII/AVRISP.txt
@@ -115,7 +115,7 @@
  *  <b><sup>2</sup></b> <i>See AUX line related tokens in the \ref SSec_Options section</i>
  *
  *  \section Sec_PDI PDI Connections
- *  Connections to the device for PDI programming<b><sup>1</sup></b> (when enabled):
+ *  Connections to the device for PDI programming (when enabled):
  *
  *  <table>
  *   <tr>
@@ -144,7 +144,7 @@
  *    <td>4</td>
  *   </tr>
  *   <tr>
- *    <td>XCLK</td>
+ *    <td>XCK</td>
  *    <td>CLOCK</td>
  *    <td>5</td>
  *   </tr>
@@ -159,7 +159,7 @@
  *  <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n
  *
  *  \section Sec_TPI TPI Connections
- *  Connections to the device for TPI programming<b><sup>1</sup></b> (when enabled):
+ *  Connections to the device for TPI programming (when enabled):
  *
  *  <table>
  *   <tr>
@@ -178,7 +178,7 @@
  *    <td>2</td>
  *   </tr>
  *   <tr>
- *    <td>XCLK <b><sup>2</sup></b></td>
+ *    <td>XCK <b><sup>2</sup></b></td>
  *    <td>CLOCK</td>
  *    <td>3</td>
  *   </tr>
@@ -241,7 +241,8 @@
  *   <tr>
  *    <td>VTARGET_ADC_CHANNEL</td>
  *    <td>Makefile CDEFS</td>
- *    <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined.</td> 
+ *    <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined.
+ *        <i>Ignored when compiled for targets lacking an ADC.</i></td> 
  *   </tr>
  *   <tr>
  *    <td>ENABLE_ISP_PROTOCOL</td>
@@ -257,9 +258,25 @@
  *    <td>NO_VTARGET_DETECT</td>
  *    <td>Makefile CDEFS</td>
  *    <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer
- *        to report a fixed 5V target voltage to the host regardless of the real target voltage.</td>  
+ *        to report a fixed 5V target voltage to the host regardless of the real target voltage. <i>Ignored when compiled for
+ *        targets lacking an ADC.</i></td>  
  *   </tr>
  *   <tr>
+ *    <td>VTARGET_REF_VOLTS</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply
+ *        voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage
+ *        to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>  
+ *   </tr>
+ *   <tr>
+ *    <td>VTARGET_SCALE_FACTOR</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the
+ *        ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be
+ *        measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set
+ *        to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>  
+ *   </tr> 
+ *   <tr>
  *    <td>LIBUSB_DRIVER_COMPAT</td>
  *    <td>Makefile CDEFS</td>
  *    <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making