X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/e071f3897a0946c6be1e1b5e1f78eda8dcbf6fc7..5de364163f5a7597ba2f54e37cdea493fbd1e7ff:/Demos/Device/LowLevel/MIDI/MIDI.c

diff --git a/Demos/Device/LowLevel/MIDI/MIDI.c b/Demos/Device/LowLevel/MIDI/MIDI.c
index 8aed527db..2cdf71152 100644
--- a/Demos/Device/LowLevel/MIDI/MIDI.c
+++ b/Demos/Device/LowLevel/MIDI/MIDI.c
@@ -37,7 +37,7 @@
 #include "MIDI.h"
 
 /** Main program entry point. This routine configures the hardware required by the application, then
- *  starts the scheduler to run the application tasks.
+ *  enters a loop to run the application tasks in sequence.
  */
 int main(void)
 {
@@ -70,7 +70,7 @@ void SetupHardware(void)
 }
 
 /** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs. */
-void EVENT_USB_Connect(void)
+void EVENT_USB_Device_Connect(void)
 {
 	/* Indicate USB enumerating */
 	LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
@@ -79,7 +79,7 @@ void EVENT_USB_Connect(void)
 /** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
  *  the status LEDs, disables the sample update and PWM output timers and stops the USB and MIDI management tasks.
  */
-void EVENT_USB_Disconnect(void)
+void EVENT_USB_Device_Disconnect(void)
 {
 	/* Indicate USB not ready */
 	LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
@@ -88,7 +88,7 @@ void EVENT_USB_Disconnect(void)
 /** Event handler for the USB_ConfigurationChanged event. This is fired when the host set the current configuration
  *  of the USB device after enumeration - the device endpoints are configured and the MIDI management task started.
  */
-void EVENT_USB_ConfigurationChanged(void)
+void EVENT_USB_Device_ConfigurationChanged(void)
 {
 	/* Indicate USB connected and ready */
 	LEDs_SetAllLEDs(LEDMASK_USB_READY);
@@ -190,7 +190,26 @@ void MIDI_Task(void)
 	/* Select the MIDI OUT stream */
 	Endpoint_SelectEndpoint(MIDI_STREAM_OUT_EPNUM);
 
-	/* Check if endpoint is ready to be read from, if so discard its (unused) data */
+	/* Check if a MIDI command has been received */
 	if (Endpoint_IsOUTReceived())
-	  Endpoint_ClearOUT();
+	{
+		USB_MIDI_EventPacket_t MIDIEvent;
+			
+		/* Read the MIDI event packet from the endpoint */
+		Endpoint_Read_Stream_LE(&MIDIEvent, sizeof(MIDIEvent));
+	
+		if (MIDIEvent.Command == (MIDI_COMMAND_NOTE_ON >> 4))
+		{
+			/* Change LEDs depending on the pitch of the sent note */
+			LEDs_SetAllLEDs(MIDIEvent.Data2 > 64 ? LEDS_LED1 : LEDS_LED2);
+		}
+		else
+		{
+			/* Turn off all LEDs in response to non-Note On messages */
+			LEDs_SetAllLEDs(LEDS_NO_LEDS);
+		}
+	
+		/* Clear the endpoint ready for new packet */
+		Endpoint_ClearOUT();
+	}
 }