X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/c79f6e2586047f66f96089e7f398622ccac80cec..77a9df36a77d2523dd2bc24fa17f9f04c6c175c5:/LUFA/Drivers/USB/Core/EndpointStream.h
diff --git a/LUFA/Drivers/USB/Core/EndpointStream.h b/LUFA/Drivers/USB/Core/EndpointStream.h
index 02a348347..f360877cf 100644
--- a/LUFA/Drivers/USB/Core/EndpointStream.h
+++ b/LUFA/Drivers/USB/Core/EndpointStream.h
@@ -51,9 +51,8 @@
/* Includes: */
#include "../../../Common/Common.h"
- #include "USBMode.h"
- #include "USBTask.h"
-
+ #include "USBMode.h"
+
/* Enable C linkage for C++ Compilers: */
#if defined(__cplusplus)
extern "C" {
@@ -105,579 +104,21 @@
*/
};
- /* Function Prototypes: */
-
- /** \name Stream functions for null data */
- //@{
-
- /** Reads and discards the given number of bytes from the currently selected endpoint's bank,
- * discarding fully read packets from the host as needed. The last packet is not automatically
- * discarded once the remaining bytes has been read; the user is responsible for manually
- * discarding the last packet from the host via the \ref Endpoint_ClearOUT() macro.
- *
- * If the BytesProcessed parameter is \c NULL, the entire stream transfer is attempted at once,
- * failing or succeeding as a single unit. If the BytesProcessed parameter points to a valid
- * storage location, the transfer will instead be performed as a series of chunks. Each time
- * the endpoint bank becomes empty while there is still data to process (and after the current
- * packet has been acknowledged) the BytesProcessed location will be updated with the total number
- * of bytes processed in the stream, and the function will exit with an error code of
- * \ref ENDPOINT_RWSTREAM_IncompleteTransfer. This allows for any abort checking to be performed
- * in the user code - to continue the transfer, call the function again with identical parameters
- * and it will resume until the BytesProcessed value reaches the total transfer length.
- *
- * Single Stream Transfer Example:
- * \code
- * uint8_t ErrorCode;
- *
- * if ((ErrorCode = Endpoint_Discard_Stream(512, NULL)) != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * Partial Stream Transfers Example:
- * \code
- * uint8_t ErrorCode;
- * uint16_t BytesProcessed;
- *
- * BytesProcessed = 0;
- * while ((ErrorCode = Endpoint_Discard_Stream(512, &BytesProcessed)) == ENDPOINT_RWSTREAM_IncompleteTransfer)
- * {
- * // Stream not yet complete - do other actions here, abort if required
- * }
- *
- * if (ErrorCode != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * \note This routine should not be used on CONTROL type endpoints.
- *
- * \param[in] Length Number of bytes to discard via the currently selected endpoint.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be read at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Discard_Stream(uint16_t Length,
- uint16_t* const BytesProcessed);
-
- /** Writes a given number of zeroed bytes to the currently selected endpoint's bank, sending
- * full packets to the host as needed. The last packet is not automatically sent once the
- * remaining bytes have been written; the user is responsible for manually sending the last
- * packet to the host via the \ref Endpoint_ClearIN() macro.
- *
- * If the BytesProcessed parameter is \c NULL, the entire stream transfer is attempted at once,
- * failing or succeeding as a single unit. If the BytesProcessed parameter points to a valid
- * storage location, the transfer will instead be performed as a series of chunks. Each time
- * the endpoint bank becomes full while there is still data to process (and after the current
- * packet transmission has been initiated) the BytesProcessed location will be updated with the
- * total number of bytes processed in the stream, and the function will exit with an error code of
- * \ref ENDPOINT_RWSTREAM_IncompleteTransfer. This allows for any abort checking to be performed
- * in the user code - to continue the transfer, call the function again with identical parameters
- * and it will resume until the BytesProcessed value reaches the total transfer length.
- *
- * Single Stream Transfer Example:
- * \code
- * uint8_t ErrorCode;
- *
- * if ((ErrorCode = Endpoint_Null_Stream(512, NULL)) != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * Partial Stream Transfers Example:
- * \code
- * uint8_t ErrorCode;
- * uint16_t BytesProcessed;
- *
- * BytesProcessed = 0;
- * while ((ErrorCode = Endpoint_Null_Stream(512, &BytesProcessed)) == ENDPOINT_RWSTREAM_IncompleteTransfer)
- * {
- * // Stream not yet complete - do other actions here, abort if required
- * }
- *
- * if (ErrorCode != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * \note This routine should not be used on CONTROL type endpoints.
- *
- * \param[in] Length Number of zero bytes to send via the currently selected endpoint.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be read at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Null_Stream(uint16_t Length,
- uint16_t* const BytesProcessed);
-
- //@}
-
- /** \name Stream functions for RAM source/destination data */
- //@{
-
- /** Writes the given number of bytes to the endpoint from the given buffer in little endian,
- * sending full packets to the host as needed. The last packet filled is not automatically sent;
- * the user is responsible for manually sending the last written packet to the host via the
- * \ref Endpoint_ClearIN() macro.
- *
- * If the BytesProcessed parameter is \c NULL, the entire stream transfer is attempted at once,
- * failing or succeeding as a single unit. If the BytesProcessed parameter points to a valid
- * storage location, the transfer will instead be performed as a series of chunks. Each time
- * the endpoint bank becomes full while there is still data to process (and after the current
- * packet transmission has been initiated) the BytesProcessed location will be updated with the
- * total number of bytes processed in the stream, and the function will exit with an error code of
- * \ref ENDPOINT_RWSTREAM_IncompleteTransfer. This allows for any abort checking to be performed
- * in the user code - to continue the transfer, call the function again with identical parameters
- * and it will resume until the BytesProcessed value reaches the total transfer length.
- *
- * Single Stream Transfer Example:
- * \code
- * uint8_t DataStream[512];
- * uint8_t ErrorCode;
- *
- * if ((ErrorCode = Endpoint_Write_Stream_LE(DataStream, sizeof(DataStream),
- * NULL)) != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * Partial Stream Transfers Example:
- * \code
- * uint8_t DataStream[512];
- * uint8_t ErrorCode;
- * uint16_t BytesProcessed;
- *
- * BytesProcessed = 0;
- * while ((ErrorCode = Endpoint_Write_Stream_LE(DataStream, sizeof(DataStream),
- * &BytesProcessed)) == ENDPOINT_RWSTREAM_IncompleteTransfer)
- * {
- * // Stream not yet complete - do other actions here, abort if required
- * }
- *
- * if (ErrorCode != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * \note This routine should not be used on CONTROL type endpoints.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be written at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Stream_LE(const void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Writes the given number of bytes to the endpoint from the given buffer in big endian,
- * sending full packets to the host as needed. The last packet filled is not automatically sent;
- * the user is responsible for manually sending the last written packet to the host via the
- * \ref Endpoint_ClearIN() macro.
- *
- * \note This routine should not be used on CONTROL type endpoints.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be written at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Stream_BE(const void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Reads the given number of bytes from the endpoint from the given buffer in little endian,
- * discarding fully read packets from the host as needed. The last packet is not automatically
- * discarded once the remaining bytes has been read; the user is responsible for manually
- * discarding the last packet from the host via the \ref Endpoint_ClearOUT() macro.
- *
- * If the BytesProcessed parameter is \c NULL, the entire stream transfer is attempted at once,
- * failing or succeeding as a single unit. If the BytesProcessed parameter points to a valid
- * storage location, the transfer will instead be performed as a series of chunks. Each time
- * the endpoint bank becomes empty while there is still data to process (and after the current
- * packet has been acknowledged) the BytesProcessed location will be updated with the total number
- * of bytes processed in the stream, and the function will exit with an error code of
- * \ref ENDPOINT_RWSTREAM_IncompleteTransfer. This allows for any abort checking to be performed
- * in the user code - to continue the transfer, call the function again with identical parameters
- * and it will resume until the BytesProcessed value reaches the total transfer length.
- *
- * Single Stream Transfer Example:
- * \code
- * uint8_t DataStream[512];
- * uint8_t ErrorCode;
- *
- * if ((ErrorCode = Endpoint_Read_Stream_LE(DataStream, sizeof(DataStream),
- * NULL)) != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * Partial Stream Transfers Example:
- * \code
- * uint8_t DataStream[512];
- * uint8_t ErrorCode;
- * uint16_t BytesProcessed;
- *
- * BytesProcessed = 0;
- * while ((ErrorCode = Endpoint_Read_Stream_LE(DataStream, sizeof(DataStream),
- * &BytesProcessed)) == ENDPOINT_RWSTREAM_IncompleteTransfer)
- * {
- * // Stream not yet complete - do other actions here, abort if required
- * }
- *
- * if (ErrorCode != ENDPOINT_RWSTREAM_NoError)
- * {
- * // Stream failed to complete - check ErrorCode here
- * }
- * \endcode
- *
- * \note This routine should not be used on CONTROL type endpoints.
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be read at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_Stream_LE(void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Reads the given number of bytes from the endpoint from the given buffer in big endian,
- * discarding fully read packets from the host as needed. The last packet is not automatically
- * discarded once the remaining bytes has been read; the user is responsible for manually
- * discarding the last packet from the host via the \ref Endpoint_ClearOUT() macro.
- *
- * \note This routine should not be used on CONTROL type endpoints.
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be read at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_Stream_BE(void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Writes the given number of bytes to the CONTROL type endpoint from the given buffer in little endian,
- * sending full packets to the host as needed. The host OUT acknowledgement is not automatically cleared
- * in both failure and success states; the user is responsible for manually clearing the setup OUT to
- * finalize the transfer via the \ref Endpoint_ClearOUT() macro.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Control_Stream_LE(const void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Writes the given number of bytes to the CONTROL type endpoint from the given buffer in big endian,
- * sending full packets to the host as needed. The host OUT acknowledgement is not automatically cleared
- * in both failure and success states; the user is responsible for manually clearing the setup OUT to
- * finalize the transfer via the \ref Endpoint_ClearOUT() macro.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Control_Stream_BE(const void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Reads the given number of bytes from the CONTROL endpoint from the given buffer in little endian,
- * discarding fully read packets from the host as needed. The device IN acknowledgement is not
- * automatically sent after success or failure states; the user is responsible for manually sending the
- * setup IN to finalize the transfer via the \ref Endpoint_ClearIN() macro.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_Control_Stream_LE(void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** Reads the given number of bytes from the CONTROL endpoint from the given buffer in big endian,
- * discarding fully read packets from the host as needed. The device IN acknowledgement is not
- * automatically sent after success or failure states; the user is responsible for manually sending the
- * setup IN to finalize the transfer via the \ref Endpoint_ClearIN() macro.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_Control_Stream_BE(void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
- //@}
-
- /** \name Stream functions for EEPROM source/destination data */
- //@{
-
- /** EEPROM buffer source version of \ref Endpoint_Write_Stream_LE().
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be written at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_EStream_LE(const void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of \ref Endpoint_Write_Stream_BE().
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be written at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_EStream_BE(const void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of \ref Endpoint_Read_Stream_LE().
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to, located in EEPROM memory space.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be read at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_EStream_LE(void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of \ref Endpoint_Read_Stream_BE().
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to, located in EEPROM memory space.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be read at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_EStream_BE(void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of Endpoint_Write_Control_Stream_LE.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Control_EStream_LE(const void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of \ref Endpoint_Write_Control_Stream_BE().
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Control_EStream_BE(const void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of \ref Endpoint_Read_Control_Stream_LE().
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_Control_EStream_LE(void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** EEPROM buffer source version of \ref Endpoint_Read_Control_Stream_BE().
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[out] Buffer Pointer to the destination data buffer to write to.
- * \param[in] Length Number of bytes to send via the currently selected endpoint.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Read_Control_EStream_BE(void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
- //@}
-
- /** \name Stream functions for PROGMEM source/destination data */
- //@{
-
- /** FLASH buffer source version of \ref Endpoint_Write_Stream_LE().
- *
- * \pre The FLASH data must be located in the first 64KB of FLASH for this function to work correctly.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be written at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_PStream_LE(const void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** FLASH buffer source version of \ref Endpoint_Write_Stream_BE().
- *
- * \pre The FLASH data must be located in the first 64KB of FLASH for this function to work correctly.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- * \param[in] BytesProcessed Pointer to a location where the total number of bytes processed in the current
- * transaction should be updated, \c NULL if the entire stream should be written at once.
- *
- * \return A value from the \ref Endpoint_Stream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_PStream_BE(const void* const Buffer,
- uint16_t Length,
- uint16_t* const BytesProcessed) ATTR_NON_NULL_PTR_ARG(1);
-
- /** FLASH buffer source version of \ref Endpoint_Write_Control_Stream_LE().
- *
- * \pre The FLASH data must be located in the first 64KB of FLASH for this function to work correctly.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Control_PStream_LE(const void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
-
- /** FLASH buffer source version of \ref Endpoint_Write_Control_Stream_BE().
- *
- * \pre The FLASH data must be located in the first 64KB of FLASH for this function to work correctly.
- *
- * \note This function automatically clears the control transfer's status stage. Do not manually attempt
- * to clear the status stage when using this routine in a control transaction.
- * \n\n
- *
- * \note This routine should only be used on CONTROL type endpoints.
- *
- * \warning Unlike the standard stream read/write commands, the control stream commands cannot be chained
- * together; i.e. the entire stream data must be read or written at the one time.
- *
- * \param[in] Buffer Pointer to the source data buffer to read from.
- * \param[in] Length Number of bytes to read for the currently selected endpoint into the buffer.
- *
- * \return A value from the \ref Endpoint_ControlStream_RW_ErrorCodes_t enum.
- */
- uint8_t Endpoint_Write_Control_PStream_BE(const void* const Buffer,
- uint16_t Length) ATTR_NON_NULL_PTR_ARG(1);
- //@}
+ /* Architecture Includes: */
+ #if (ARCH == ARCH_AVR8)
+ #include "AVR8/EndpointStream_AVR8.h"
+ #elif (ARCH == ARCH_UC3)
+ #include "UC3/EndpointStream_UC3.h"
+ #elif (ARCH == ARCH_XMEGA)
+ #include "XMEGA/EndpointStream_XMEGA.h"
+ #endif
/* Disable C linkage for C++ Compilers: */
#if defined(__cplusplus)
}
#endif
-
+
#endif
/** @} */
-
+