X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/bd337aced3b1888373030878bf1a49367bc37ab5..d4684b29b9a3a4b45b6422d0f1cf6c79639c84c8:/Demos/Device/ClassDriver/AudioInput/AudioInput.txt

diff --git a/Demos/Device/ClassDriver/AudioInput/AudioInput.txt b/Demos/Device/ClassDriver/AudioInput/AudioInput.txt
index fea31b66e..dfa9362c2 100644
--- a/Demos/Device/ClassDriver/AudioInput/AudioInput.txt
+++ b/Demos/Device/ClassDriver/AudioInput/AudioInput.txt
@@ -6,15 +6,15 @@
 
 /** \mainpage Audio Input Device Demo
  *
- *  \section SSec_Compat Demo Compatibility:
+ *  \section Sec_Compat Demo Compatibility:
  *
  *  The following list indicates what microcontrollers are compatible with this demo.
  *
- *  - Series 7 USB AVRs (AT90USBxxx7)
- *  - Series 6 USB AVRs (AT90USBxxx6)
- *  - Series 4 USB AVRs (ATMEGAxxU4)
+ *  \li Series 7 USB AVRs (AT90USBxxx7)
+ *  \li Series 6 USB AVRs (AT90USBxxx6)
+ *  \li Series 4 USB AVRs (ATMEGAxxU4)
  *
- *  \section SSec_Info USB Information:
+ *  \section Sec_Info USB Information:
  *
  *  The following table gives a rundown of the USB utilization of this demo.
  *
@@ -38,12 +38,12 @@
  *        USBIF Audio 1.0 Data Formats Specification</td>
  *   </tr>
  *   <tr>
- *    <td><b>Usable Speeds:</b></td>
+ *    <td><b>Supported USB Speeds:</b></td>
  *    <td>Full Speed Mode</td>
  *   </tr>
  *  </table>
  *
- *  \section SSec_Description Project Description:
+ *  \section Sec_Description Project Description:
  *
  *  Audio demonstration application. This gives a simple reference
  *  application for implementing a USB Audio Input device using the
@@ -61,7 +61,7 @@
  *  Under Windows, if a driver request dialogue pops up, select the option
  *  to automatically install the appropriate drivers.
  *
- *  \section SSec_Options Project Options
+ *  \section Sec_Options Project Options
  *
  *  The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value.
  *
@@ -72,21 +72,21 @@
  *    <td><b>Description:</b></td>
  *   </tr>
  *   <tr>
+ *    <td>MIC_IN_ADC_CHANNEL</td>
+ *    <td>AppConfig.h</td>
+ *    <td>Sets the ADC channel used by the demo for the input audio samples from an attached microphone.</td>
+ *   </tr>
+ *   <tr>
  *    <td>USE_TEST_TONE</td>
- *    <td>Makefile LUFA_OPTS</td>
+ *    <td>AppConfig.h</td>
  *    <td>When defined, this alters the demo to produce a square wave test tone when the first board button is pressed
  *        instead of sampling the board microphone.</td>
  *   </tr>
  *   <tr>
  *    <td>MICROPHONE_BIASED_TO_HALF_RAIL</td>
- *    <td>Makefile LUFA_OPTS</td>
+ *    <td>AppConfig.h</td>
  *    <td>When defined, this alters the demo so that the half VCC bias of the microphone input is subtracted.</td>
  *   </tr>
- *   <tr>
- *    <td>AUDIO_SAMPLE_FREQUENCY</td>
- *    <td>Descriptors.h</td>
- *    <td>Gives the audio sample rate per channel for the audio stream, in Hz.</td>
- *   </tr>
  *  </table>
  */