X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/958a1b4e2bffdc548b34edd322d30cec5d5feacd..4a8ac5e474741f14492597880e751b3f806cb965:/Demos/Device/GenericHID/GenericHID.c

diff --git a/Demos/Device/GenericHID/GenericHID.c b/Demos/Device/GenericHID/GenericHID.c
index d4e7cca73..f43499a0f 100644
--- a/Demos/Device/GenericHID/GenericHID.c
+++ b/Demos/Device/GenericHID/GenericHID.c
@@ -39,10 +39,7 @@
 /* Scheduler Task List */
 TASK_LIST
 {
-	#if !defined(INTERRUPT_CONTROL_ENDPOINT)
 	{ .Task = USB_USBTask          , .TaskStatus = TASK_STOP },
-	#endif
-	
 	{ .Task = USB_HID_Report       , .TaskStatus = TASK_STOP },
 };
 
@@ -75,30 +72,13 @@ int main(void)
 	Scheduler_Start();
 }
 
-/** Event handler for the USB_Reset event. This fires when the USB interface is reset by the USB host, before the
- *  enumeration process begins, and enables the control endpoint interrupt so that control requests can be handled
- *  asynchronously when they arrive rather than when the control endpoint is polled manually.
- */
-EVENT_HANDLER(USB_Reset)
-{
-	#if defined(INTERRUPT_CONTROL_ENDPOINT)
-	/* Select the control endpoint */
-	Endpoint_SelectEndpoint(ENDPOINT_CONTROLEP);
-
-	/* Enable the endpoint SETUP interrupt ISR for the control endpoint */
-	USB_INT_Enable(ENDPOINT_INT_SETUP);
-	#endif
-}
-
 /** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
  *  starts the library USB task to begin the enumeration and USB management process.
  */
-EVENT_HANDLER(USB_Connect)
+void EVENT_USB_Connect(void)
 {
-	#if !defined(INTERRUPT_CONTROL_ENDPOINT)
 	/* Start USB management task */
 	Scheduler_SetTaskMode(USB_USBTask, TASK_RUN);
-	#endif
 
 	/* Indicate USB enumerating */
 	UpdateStatus(Status_USBEnumerating);
@@ -107,14 +87,11 @@ EVENT_HANDLER(USB_Connect)
 /** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
  *  the status LEDs and stops the USB management task.
  */
-EVENT_HANDLER(USB_Disconnect)
+void EVENT_USB_Disconnect(void)
 {
 	/* Stop running HID reporting and USB management tasks */
 	Scheduler_SetTaskMode(USB_HID_Report, TASK_STOP);
-
-	#if !defined(INTERRUPT_CONTROL_ENDPOINT)
 	Scheduler_SetTaskMode(USB_USBTask, TASK_STOP);
-	#endif
 
 	/* Indicate USB not ready */
 	UpdateStatus(Status_USBNotReady);
@@ -123,7 +100,7 @@ EVENT_HANDLER(USB_Disconnect)
 /** Event handler for the USB_ConfigurationChanged event. This is fired when the host sets the current configuration
  *  of the USB device after enumeration, and configures the generic HID device endpoints.
  */
-EVENT_HANDLER(USB_ConfigurationChanged)
+void EVENT_USB_ConfigurationChanged(void)
 {
 	/* Setup Generic IN Report Endpoint */
 	Endpoint_ConfigureEndpoint(GENERIC_IN_EPNUM, EP_TYPE_INTERRUPT,
@@ -143,7 +120,7 @@ EVENT_HANDLER(USB_ConfigurationChanged)
  *  control requests that are not handled internally by the USB library (including the HID commands, which are
  *  all issued via the control endpoint), so that they can be handled appropriately for the application.
  */
-EVENT_HANDLER(USB_UnhandledControlPacket)
+void EVENT_USB_UnhandledControlPacket(void)
 {
 	/* Handle HID Class specific requests */
 	switch (USB_ControlRequest.bRequest)
@@ -298,32 +275,3 @@ TASK(USB_HID_Report)
 		}
 	}
 }
-
-#if defined(INTERRUPT_CONTROL_ENDPOINT)
-/** ISR for the general Pipe/Endpoint interrupt vector. This ISR fires when an endpoint's status changes (such as
- *  a packet has been received) on an endpoint with its corresponding ISR enabling bits set. This is used to send
- *  HID packets to the host each time the HID interrupt endpoints polling period elapses, as managed by the USB
- *  controller.
- */
-ISR(ENDPOINT_PIPE_vect, ISR_BLOCK)
-{
-	/* Save previously selected endpoint before selecting a new endpoint */
-	uint8_t PrevSelectedEndpoint = Endpoint_GetCurrentEndpoint();
-
-	/* Check if the control endpoint has received a request */
-	if (Endpoint_HasEndpointInterrupted(ENDPOINT_CONTROLEP))
-	{
-		/* Clear the endpoint interrupt */
-		Endpoint_ClearEndpointInterrupt(ENDPOINT_CONTROLEP);
-
-		/* Process the control request */
-		USB_USBTask();
-
-		/* Handshake the endpoint setup interrupt - must be after the call to USB_USBTask() */
-		USB_INT_Clear(ENDPOINT_INT_SETUP);
-	}
-
-	/* Restore previously selected endpoint */
-	Endpoint_SelectEndpoint(PrevSelectedEndpoint);
-}
-#endif