X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/3e515cdfa8d8f077c2585c061c6f4a988031c82b..fbabecee66b93596acc6f99a92be4a9dd3a750ce:/Projects/AVRISP-MKII/AVRISP.txt

diff --git a/Projects/AVRISP-MKII/AVRISP.txt b/Projects/AVRISP-MKII/AVRISP.txt
index 8d00d35d3..c4ba43ccc 100644
--- a/Projects/AVRISP-MKII/AVRISP.txt
+++ b/Projects/AVRISP-MKII/AVRISP.txt
@@ -57,7 +57,6 @@
  *    - Minimum ISP target clock speed of 500KHz due to hardware SPI module prescaler limitations
  *    - No reversed/shorted target connector detection and notification
  *    - A seperate header is required for each of the ISP, PDI and TPI programming protocols that the user wishes to use
- *    - XMEGA EEPROM erase section command does not work (but EEPROM read/write and chip erase does)
  *
  *  On AVR models with an ADC converter, AVCC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
  *  set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
@@ -144,7 +143,7 @@
  *    <td>4</td>
  *   </tr>
  *   <tr>
- *    <td>XCLK</td>
+ *    <td>XCK</td>
  *    <td>CLOCK</td>
  *    <td>5</td>
  *   </tr>
@@ -178,7 +177,7 @@
  *    <td>2</td>
  *   </tr>
  *   <tr>
- *    <td>XCLK <b><sup>2</sup></b></td>
+ *    <td>XCK <b><sup>2</sup></b></td>
  *    <td>CLOCK</td>
  *    <td>3</td>
  *   </tr>
@@ -262,6 +261,21 @@
  *        targets lacking an ADC.</i></td>  
  *   </tr>
  *   <tr>
+ *    <td>VTARGET_REF_VOLTS</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply
+ *        voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage
+ *        to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>  
+ *   </tr>
+ *   <tr>
+ *    <td>VTARGET_SCALE_FACTOR</td>
+ *    <td>Makefile CDEFS</td>
+ *    <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the
+ *        ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be
+ *        measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set
+ *        to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>  
+ *   </tr> 
+ *   <tr>
  *    <td>LIBUSB_DRIVER_COMPAT</td>
  *    <td>Makefile CDEFS</td>
  *    <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making