X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/3d4d8e7f628f9dc9981242f69b097333faa9940d..d4684b29b9a3a4b45b6422d0f1cf6c79639c84c8:/Projects/XPLAINBridge/makefile

diff --git a/Projects/XPLAINBridge/makefile b/Projects/XPLAINBridge/makefile
index 437d70ad9..5c962b574 100644
--- a/Projects/XPLAINBridge/makefile
+++ b/Projects/XPLAINBridge/makefile
@@ -79,8 +79,8 @@ BOARD = XPLAIN
 #     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
 #     automatically to create a 32-bit value in your source code.
 #
-#     This will be an integer division of F_CLOCK below, as it is sourced by
-#     F_CLOCK after it has run through any CPU prescalers. Note that this value
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
 #     does not *change* the processor frequency - it should merely be updated to
 #     reflect the processor speed set externally so that the code can use accurate
 #     software delays.
@@ -88,7 +88,7 @@ F_CPU = 8000000
 
 
 # Input clock frequency.
-#     This will define a symbol, F_CLOCK, in all source code files equal to the
+#     This will define a symbol, F_USB, in all source code files equal to the
 #     input clock frequency (before any prescaling is performed) in Hz. This value may
 #     differ from F_CPU if prescaling is used on the latter, and is required as the
 #     raw input clock is fed directly to the PLL sections of the AVR for high speed
@@ -98,7 +98,7 @@ F_CPU = 8000000
 #
 #     If no clock division is performed on the input clock inside the AVR (via the
 #     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_CLOCK = $(F_CPU)
+F_USB = $(F_CPU)
 
 
 # Output format. (can be srec, ihex, binary)
@@ -124,24 +124,7 @@ AVRISP_PATH = ../AVRISP-MKII
 
 
 # LUFA library compile-time options and predefined tokens
-LUFA_OPTS  = -D USB_DEVICE_ONLY
-LUFA_OPTS += -D DEVICE_STATE_AS_GPIOR=0
-LUFA_OPTS += -D ORDERED_EP_CONFIG
-LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8
-LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1
-LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
-LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
-LUFA_OPTS += -D NO_DEVICE_REMOTE_WAKEUP
-LUFA_OPTS += -D NO_DEVICE_SELF_POWER
-
-LUFA_OPTS += -D AUX_LINE_PORT=PORTB
-LUFA_OPTS += -D AUX_LINE_PIN=PINB
-LUFA_OPTS += -D AUX_LINE_DDR=DDRB
-LUFA_OPTS += -D AUX_LINE_MASK="(1 << 4)"
-LUFA_OPTS += -D VTARGET_ADC_CHANNEL=2
-LUFA_OPTS += -D VTARGET_REF_VOLTS=3.3
-LUFA_OPTS += -D VTARGET_SCALE_FACTOR=2
-#LUFA_OPTS += -D LIBUSB_DRIVER_COMPAT
+LUFA_OPTS  = -D USE_LUFA_CONFIG_HEADER
 
 
 # Create the LUFA source path variables by including the LUFA root makefile
@@ -150,9 +133,9 @@ include $(LUFA_PATH)/LUFA/makefile
 
 # List C source files here. (C dependencies are automatically generated.)
 SRC = $(TARGET).c                                                 \
-	  AVRISPDescriptors.c                                         \
-	  USARTDescriptors.c                                          \
 	  Lib/SoftUART.c                                              \
+	  USARTDescriptors.c                                          \
+	  $(AVRISP_PATH)/AVRISPDescriptors.c                          \
 	  $(AVRISP_PATH)/Lib/V2Protocol.c                             \
 	  $(AVRISP_PATH)/Lib/V2ProtocolParams.c                       \
 	  $(AVRISP_PATH)/Lib/ISP/ISPProtocol.c                        \
@@ -196,7 +179,7 @@ DEBUG = dwarf-2
 #     Each directory must be seperated by a space.
 #     Use forward slashes for directory separators.
 #     For a directory that has spaces, enclose it in quotes.
-EXTRAINCDIRS = $(LUFA_PATH)/ $(AVRISP_PATH)/
+EXTRAINCDIRS = $(LUFA_PATH)/ $(AVRISP_PATH)/ Config/
 
 
 # Compiler flag to set the C Standard level.
@@ -209,20 +192,20 @@ CSTANDARD = -std=c99
 
 # Place -D or -U options here for C sources
 CDEFS  = -DF_CPU=$(F_CPU)UL
-CDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CDEFS += -DF_USB=$(F_USB)UL
 CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
 CDEFS += $(LUFA_OPTS)
 
 
 # Place -D or -U options here for ASM sources
 ADEFS  = -DF_CPU=$(F_CPU)
-ADEFS += -DF_CLOCK=$(F_CLOCK)UL
+ADEFS += -DF_USB=$(F_USB)UL
 ADEFS += -DBOARD=BOARD_$(BOARD)
 ADEFS += $(LUFA_OPTS)
 
 # Place -D or -U options here for C++ sources
 CPPDEFS  = -DF_CPU=$(F_CPU)UL
-CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CPPDEFS += -DF_USB=$(F_USB)UL
 CPPDEFS += -DBOARD=BOARD_$(BOARD)
 CPPDEFS += $(LUFA_OPTS)
 #CPPDEFS += -D__STDC_LIMIT_MACROS
@@ -247,6 +230,7 @@ CFLAGS += -fno-inline-small-functions
 CFLAGS += -fpack-struct
 CFLAGS += -fshort-enums
 CFLAGS += -fno-strict-aliasing
+CFLAGS += -fno-split-wide-types
 CFLAGS += -Wall
 CFLAGS += -Wstrict-prototypes
 #CFLAGS += -mshort-calls
@@ -721,13 +705,24 @@ clean_list :
 	$(REMOVEDIR) .dep
 
 doxygen:
-	@echo Generating Project Documentation...
-	@doxygen Doxygen.conf
+	@echo Generating Project Documentation \($(TARGET)\)...
+	@if ( ( cat Doxygen.conf ; echo "HTML_STYLESHEET=$(LUFA_PATH)/LUFA/DoxygenPages/Style/Style.css" ) | doxygen - 2>&1 | grep -v "warning: ignoring unsupported tag" ;); then \
+	  exit 1; \
+	fi;
 	@echo Documentation Generation Complete.
 
 clean_doxygen:
 	rm -rf Documentation
 
+checksource:
+	@for f in $(SRC) $(CPPSRC) $(ASRC); do \
+		if [ -f $$f ]; then \
+			echo "Found Source File: $$f" ; \
+		else \
+			echo "Source File Not Found: $$f" ; \
+		fi; done 
+
+
 # Create object files directory
 $(shell mkdir $(OBJDIR) 2>/dev/null)
 
@@ -740,5 +735,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null)
 .PHONY : all begin finish end sizebefore sizeafter gccversion \
 build elf hex eep lss sym coff extcoff doxygen clean          \
 clean_list clean_doxygen program dfu flip flip-ee dfu-ee      \
-debug gdb-config
-
+debug gdb-config checksource