X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/39f1c0c136520a3f4746ad6381d1242979125ff3..deb181ae2c27db872c471a77e85d7190f32962c3:/firmware/usbdrv/usbconfig-prototype.h

diff --git a/firmware/usbdrv/usbconfig-prototype.h b/firmware/usbdrv/usbconfig-prototype.h
index 6c9e37a82..847710e2a 100644
--- a/firmware/usbdrv/usbconfig-prototype.h
+++ b/firmware/usbdrv/usbconfig-prototype.h
@@ -1,11 +1,11 @@
 /* Name: usbconfig.h
- * Project: AVR USB driver
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
  * Author: Christian Starkjohann
  * Creation Date: 2005-04-01
  * Tabsize: 4
  * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
  * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbconfig-prototype.h 692 2008-11-07 15:07:40Z cs $
+ * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
  */
 
 #ifndef __usbconfig_h_included__
@@ -14,7 +14,7 @@
 /*
 General Description:
 This file is an example configuration (with inline documentation) for the USB
-driver. It configures AVR-USB for USB D+ connected to Port D bit 2 (which is
+driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
 also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
 wire the lines to any other port, as long as D+ is also wired to INT0 (or any
 other hardware interrupt, as long as it is the highest level interrupt, see
@@ -44,11 +44,19 @@ section at the end of this file).
  * markers every millisecond.]
  */
 #define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
-/* Clock rate of the AVR in MHz. Legal values are 12000, 12800, 15000, 16000,
- * 16500 and 20000. The 12.8 MHz and 16.5 MHz versions of the code require no
- * crystal, they tolerate +/- 1% deviation from the nominal frequency. All
- * other rates require a precision of 2000 ppm and thus a crystal!
- * Default if not specified: 12 MHz
+/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
+ * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
+ * require no crystal, they tolerate +/- 1% deviation from the nominal
+ * frequency. All other rates require a precision of 2000 ppm and thus a
+ * crystal!
+ * Since F_CPU should be defined to your actual clock rate anyway, you should
+ * not need to modify this setting.
+ */
+#define USB_CFG_CHECK_CRC       0
+/* Define this to 1 if you want that the driver checks integrity of incoming
+ * data packets (CRC checks). CRC checks cost quite a bit of code size and are
+ * currently only available for 18 MHz crystal clock. You must choose
+ * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
  */
 
 /* ----------------------- Optional Hardware Config ------------------------ */
@@ -138,6 +146,11 @@ section at the end of this file).
  * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
  * usbdrv.h.
  */
+#define USB_CFG_DRIVER_FLASH_PAGE       0
+/* If the device has more than 64 kBytes of flash, define this to the 64 k page
+ * where the driver's constants (descriptors) are located. Or in other words:
+ * Define this to 1 for boot loaders on the ATMega128.
+ */
 #define USB_CFG_LONG_TRANSFERS          0
 /* Define this to 1 if you want to send/receive blocks of more than 254 bytes
  * in a single control-in or control-out transfer. Note that the capability
@@ -195,24 +208,36 @@ section at the end of this file).
 /* define this macro to 1 if you want the function usbMeasureFrameLength()
  * compiled in. This function can be used to calibrate the AVR's RC oscillator.
  */
+#define USB_USE_FAST_CRC                0
+/* The assembler module has two implementations for the CRC algorithm. One is
+ * faster, the other is smaller. This CRC routine is only used for transmitted
+ * messages where timing is not critical. The faster routine needs 31 cycles
+ * per byte while the smaller one needs 61 to 69 cycles. The faster routine
+ * may be worth the 32 bytes bigger code size if you transmit lots of data and
+ * run the AVR close to its limit.
+ */
 
 /* -------------------------- Device Description --------------------------- */
 
-#define  USB_CFG_VENDOR_ID       0xc0, 0x16
+#define  USB_CFG_VENDOR_ID       0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
 /* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you use one of obdev's free shared
- * VID/PID pairs. Be sure to read USBID-License.txt for rules!
- * + This template uses obdev's shared VID/PID pair: 0x16c0/0x5dc.
- * + Use this VID/PID pair ONLY if you understand the implications!
- */
-#define  USB_CFG_DEVICE_ID       0xdc, 0x05
+ * own Vendor ID, define it here. Otherwise you may use one of obdev's free
+ * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
+ */
+#define  USB_CFG_DEVICE_ID       0xdc, 0x05 /* = 0x05dc = 1500 */
 /* This is the ID of the product, low byte first. It is interpreted in the
  * scope of the vendor ID. If you have registered your own VID with usb.org
  * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you use obdev's free shared VID/PID pair. Be sure to read the rules in
- * USBID-License.txt!
- * + This template uses obdev's shared VID/PID pair: 0x16c0/0x5dc.
- * + Use this VID/PID pair ONLY if you understand the implications!
+ * you may use one of obdev's free shared VID/PID pairs. See the file
+ * USB-IDs-for-free.txt for details!
+ * *** IMPORTANT NOTE ***
+ * This template uses obdev's shared VID/PID pair for Vendor Class devices
+ * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
+ * the implications!
  */
 #define USB_CFG_DEVICE_VERSION  0x00, 0x01
 /* Version number of the device: Minor number first, then major number.
@@ -224,14 +249,14 @@ section at the end of this file).
  * are interpreted as Unicode (UTF-16) entities.
  * If you don't want a vendor name string, undefine these macros.
  * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USBID-License.txt for
+ * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
  * details.
  */
 #define USB_CFG_DEVICE_NAME     'T', 'e', 'm', 'p', 'l', 'a', 't', 'e'
 #define USB_CFG_DEVICE_NAME_LEN 8
 /* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USBID-License.txt before you assign a name if you
- * use a shared VID/PID.
+ * the macros. See the file USB-IDs-for-free.txt before you assign a name if
+ * you use a shared VID/PID.
  */
 /*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
 /*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
@@ -346,6 +371,6 @@ section at the end of this file).
 /* #define USB_INTR_ENABLE_BIT     INT0 */
 /* #define USB_INTR_PENDING        GIFR */
 /* #define USB_INTR_PENDING_BIT    INTF0 */
-/* #define USB_INTR_VECTOR         SIG_INTERRUPT0 */
+/* #define USB_INTR_VECTOR         INT0_vect */
 
 #endif /* __usbconfig_h_included__ */