X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/37b2130fb2767a39f3d95414c6aca75a67c26298..2ee9fc707784e115d744dbc229bdc893f4bb6bc1:/Demos/Device/CDC/CDC.c

diff --git a/Demos/Device/CDC/CDC.c b/Demos/Device/CDC/CDC.c
index 4c51fc6b7..d7ebb9e6b 100644
--- a/Demos/Device/CDC/CDC.c
+++ b/Demos/Device/CDC/CDC.c
@@ -104,7 +104,7 @@ int main(void)
 /** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
  *  starts the library USB task to begin the enumeration and USB management process.
  */
-EVENT_HANDLER(USB_Connect)
+void EVENT_USB_Connect(void)
 {
 	/* Start USB management task */
 	Scheduler_SetTaskMode(USB_USBTask, TASK_RUN);
@@ -116,7 +116,7 @@ EVENT_HANDLER(USB_Connect)
 /** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
  *  the status LEDs and stops the USB management and CDC management tasks.
  */
-EVENT_HANDLER(USB_Disconnect)
+void EVENT_USB_Disconnect(void)
 {
 	/* Stop running CDC and USB management tasks */
 	Scheduler_SetTaskMode(CDC_Task, TASK_STOP);
@@ -129,7 +129,7 @@ EVENT_HANDLER(USB_Disconnect)
 /** Event handler for the USB_ConfigurationChanged event. This is fired when the host set the current configuration
  *  of the USB device after enumeration - the device endpoints are configured and the CDC management task started.
  */
-EVENT_HANDLER(USB_ConfigurationChanged)
+void EVENT_USB_ConfigurationChanged(void)
 {
 	/* Setup CDC Notification, Rx and Tx Endpoints */
 	Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT,
@@ -155,61 +155,55 @@ EVENT_HANDLER(USB_ConfigurationChanged)
  *  control requests that are not handled internally by the USB library (including the CDC control commands,
  *  which are all issued via the control endpoint), so that they can be handled appropriately for the application.
  */
-EVENT_HANDLER(USB_UnhandledControlPacket)
+void EVENT_USB_UnhandledControlPacket(void)
 {
 	uint8_t* LineCodingData = (uint8_t*)&LineCoding;
 
 	/* Process CDC specific control requests */
-	switch (bRequest)
+	switch (USB_ControlRequest.bRequest)
 	{
 		case REQ_GetLineEncoding:
-			if (bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
+			if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
 			{	
 				/* Acknowledge the SETUP packet, ready for data transfer */
-				Endpoint_ClearControlSETUP();
+				Endpoint_ClearSETUP();
 
 				/* Write the line coding data to the control endpoint */
 				Endpoint_Write_Control_Stream_LE(LineCodingData, sizeof(CDC_Line_Coding_t));
 				
 				/* Finalize the stream transfer to send the last packet or clear the host abort */
-				Endpoint_ClearControlOUT();
+				Endpoint_ClearOUT();
 			}
 			
 			break;
 		case REQ_SetLineEncoding:
-			if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
+			if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
 			{
 				/* Acknowledge the SETUP packet, ready for data transfer */
-				Endpoint_ClearControlSETUP();
+				Endpoint_ClearSETUP();
 
 				/* Read the line coding data in from the host into the global struct */
 				Endpoint_Read_Control_Stream_LE(LineCodingData, sizeof(CDC_Line_Coding_t));
 
 				/* Finalize the stream transfer to clear the last packet from the host */
-				Endpoint_ClearControlIN();
+				Endpoint_ClearIN();
 			}
 	
 			break;
 		case REQ_SetControlLineState:
-			if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
+			if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
 			{
-#if 0
+				/* Acknowledge the SETUP packet, ready for data transfer */
+				Endpoint_ClearSETUP();
+				
 				/* NOTE: Here you can read in the line state mask from the host, to get the current state of the output handshake
-				         lines. The mask is read in from the wValue parameter, and can be masked against the CONTROL_LINE_OUT_* masks
-				         to determine the RTS and DTR line states using the following code:
+				         lines. The mask is read in from the wValue parameter in USB_ControlRequest, and can be masked against the
+						 CONTROL_LINE_OUT_* masks to determine the RTS and DTR line states using the following code:
 				*/
-
-				uint16_t wIndex = Endpoint_Read_Word_LE();
-					
-				// Do something with the given line states in wIndex
-#endif
-				
-				/* Acknowledge the SETUP packet, ready for data transfer */
-				Endpoint_ClearControlSETUP();
 				
 				/* Acknowledge status stage */
 				while (!(Endpoint_IsINReady()));
-				Endpoint_ClearControlIN();
+				Endpoint_ClearIN();
 			}
 	
 			break;