X-Git-Url: http://git.linex4red.de/pub/USBasp.git/blobdiff_plain/071e02c6b6b4837fa9cf0b6d4c749994e02638d7..6d67b1df3cb8300612ad7b2f16e6bffe08fb8f30:/Projects/XPLAINBridge/XPLAINBridge.txt

diff --git a/Projects/XPLAINBridge/XPLAINBridge.txt b/Projects/XPLAINBridge/XPLAINBridge.txt
index 0c5635ac7..353241788 100644
--- a/Projects/XPLAINBridge/XPLAINBridge.txt
+++ b/Projects/XPLAINBridge/XPLAINBridge.txt
@@ -3,16 +3,16 @@
  *  This file contains special DoxyGen information for the generation of the main page and other special
  *  documentation pages. It is not a project source file.
  */
- 
+
 /** \mainpage XPLAIN UART Bridge/PDI Programmer Project
  *
- *  \section SSec_Compat Project Compatibility:
+ *  \section Sec_Compat Project Compatibility:
  *
  *  The following list indicates what microcontrollers are compatible with this project.
  *
  *  - AT90USB1287
  *
- *  \section SSec_Info USB Information:
+ *  \section Sec_Info USB Information:
  *
  *  The following table gives a rundown of the USB utilization of this project.
  *
@@ -27,7 +27,7 @@
  *    <td>1) Communications Device Class (CDC)</td>
  *    <td>2) Vendor Specific Class</td>
  *   </tr>
- *   <tr> 
+ *   <tr>
  *    <td><b>USB Subclass:</b></td>
  *    <td>1) Abstract Control Model (ACM)</td>
  *    <td>2) N/A</td>
@@ -44,26 +44,31 @@
  *   </tr>
  *  </table>
  *
- *  \section SSec_Description Project Description: 
+ *  \section Sec_Description Project Description:
  *
  *  This project serves a dual purpose. When loaded into the USB AVR on the XPLAIN board, it will act as either a USB to Serial
- *  converter for the XPLAIN's hardware USART (at a speed of 9600 baud), or an AVRStudio compaible PDI programmer for the XMEGA.
+ *  converter for the XPLAIN's hardware USART (at a speed of 9600 baud), or an AVRStudio compatible PDI programmer for the XMEGA.
  *  This project replaces the firmware preloaded onto the XPLAIN's onboard AT90USB1287 microcontroller.
  *
  *  When power to the board is applied, the TDI pin (pin 9) of the USB AVR's JTAG port is read. If the pin is left high, the device
  *  will enumerate as a regular COM port on the host, which can then be opened and data exchanged between the XMEGA and Host as if
  *  the XMEGA was connected directly to the host's serial port. If the pin is pulled low by shorting it to GND (pin 10), the device
  *  will enumerate as an AVRISP-MKII to the host, so that the XMEGA can be reprogrammed by AVRStudio or other compatible software
- *  such as avrdude.
+ *  such as avrdude by connecting to the board as if it was an Atmel AVRISP-MKII programmer.
+ *
+ *  After running this project in serial bridge mode for the first time on a new computer, you will need to supply the .INF file
+ *  located in this project project's directory as the device's driver when running under Windows. This will enable Windows to use
+ *  its inbuilt CDC virtual serial drivers, negating the need for custom drivers for the device. Other Operating Systems should
+ *  automatically use their own inbuilt CDC-ACM drivers.
  *
- *  After running this project for the first time on a new computer, you will need to supply the .INF file located in this project
- *  project's directory as the device's driver when running under Windows. This will enable Windows to use its inbuilt CDC drivers,
- *  negating the need for custom drivers for the device. Other Operating Systems should automatically use their own inbuilt CDC-ACM
- *  drivers.
+ *  In serial bridge mode, the UART baud rate can be altered through the host terminal software to select a new baud rate - the default
+ *  baud is 9600. Note that parity, data bits and stop bits are fixed at none, eight and one respectively can cannot be altered. Changes
+ *  to the connection's parity, data bits or stop bits are ignored by the firmware. As the serial link between the controllers on the
+ *  XPLAIN is software emulated by the USB AVR, not all baud rates will work correctly.
  *
  *  This project relies on files from the LUFA AVRISP-MKII project for compilation.
  *
- *  \section SSec_Options Project Options
+ *  \section Sec_Options Project Options
  *
  *  The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
  *
@@ -74,16 +79,16 @@
  *    <td><b>Description:</b></td>
  *   </tr>
  *   <tr>
- *    <td>BUFF_STATICSIZE</td>
- *    <td>RingBuff.h</td>
- *    <td>Defines the maximum number of bytes which can be buffered in each Ring Buffer.</td>
+ *    <td>BUFFER_SIZE</td>
+ *    <td>LightweightRingBuff.h</td>
+ *    <td>Defines the maximum number of bytes which can be buffered in each Ring Buffer when in serial bridge mode.</td>
  *   </tr>
  *   <tr>
- *    <td>LIBUSB_FILTERDRV_COMPAT</td>
- *    <td>Makefile CDEFS</td>
+ *    <td>LIBUSB_DRIVER_COMPAT</td>
+ *    <td>Makefile LUFA_OPTS</td>
  *    <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making
- *        the code compatible with Windows builds of avrdude using the libUSB driver. Linux platforms are not affected by this
- *        option.
+ *        the code compatible with software such as avrdude (all platforms) that use the libUSB driver.
  *   </tr>
  *  </table>
- */
\ No newline at end of file
+ */
+