/*
LUFA Library
- Copyright (C) Dean Camera, 2010.
+ Copyright (C) Dean Camera, 2012.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
- Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
+ Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
/** Contains the current baud rate and other settings of the first virtual serial port. This must be retained as some
* operating systems will not open the port unless the settings can be set successfully.
*/
-CDC_Line_Coding_t LineEncoding = { .BaudRateBPS = 0,
- .CharFormat = OneStopBit,
- .ParityType = Parity_None,
- .DataBits = 8 };
+static CDC_LineEncoding_t LineEncoding = { .BaudRateBPS = 0,
+ .CharFormat = CDC_LINEENCODING_OneStopBit,
+ .ParityType = CDC_PARITY_None,
+ .DataBits = 8 };
/** Current address counter. This stores the current address of the FLASH or EEPROM as set by the host,
* and is used when reading or writing to the AVRs memory (either FLASH or EEPROM depending on the issued
* command.)
*/
-uint32_t CurrAddress;
+static uint32_t CurrAddress;
/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
* via a watchdog reset. When cleared the bootloader will exit, starting the watchdog and entering an infinite
* loop until the AVR restarts and the application runs.
*/
-bool RunBootloader = true;
+static bool RunBootloader = true;
/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
/* Setup hardware required for the bootloader */
SetupHardware();
+ /* Turn on first LED on the board to indicate that the bootloader has started */
+ LEDs_SetAllLEDs(LEDS_LED1);
+
/* Enable global interrupts so that the USB stack can function */
sei();
}
/** Configures all hardware required for the bootloader. */
-void SetupHardware(void)
+static void SetupHardware(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
MCUCR = (1 << IVCE);
MCUCR = (1 << IVSEL);
- /* Initialize USB Subsystem */
+ /* Initialize the USB and other board hardware drivers */
USB_Init();
+ LEDs_Init();
+
+ /* Bootloader active LED toggle timer initialization */
+ TIMSK1 = (1 << TOIE1);
+ TCCR1B = ((1 << CS11) | (1 << CS10));
+}
+
+/** ISR to periodically toggle the LEDs on the board to indicate that the bootloader is active. */
+ISR(TIMER1_OVF_vect, ISR_BLOCK)
+{
+ LEDs_ToggleLEDs(LEDS_LED1 | LEDS_LED2);
}
/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready
*/
void EVENT_USB_Device_ControlRequest(void)
{
+ /* Ignore any requests that aren't directed to the CDC interface */
+ if ((USB_ControlRequest.bmRequestType & (CONTROL_REQTYPE_TYPE | CONTROL_REQTYPE_RECIPIENT)) !=
+ (REQTYPE_CLASS | REQREC_INTERFACE))
+ {
+ return;
+ }
+
+ /* Activity - toggle indicator LEDs */
+ LEDs_ToggleLEDs(LEDS_LED1 | LEDS_LED2);
+
/* Process CDC specific control requests */
switch (USB_ControlRequest.bRequest)
{
- case REQ_GetLineEncoding:
+ case CDC_REQ_GetLineEncoding:
if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSETUP();
/* Write the line coding data to the control endpoint */
- Endpoint_Write_Control_Stream_LE(&LineEncoding, sizeof(CDC_Line_Coding_t));
+ Endpoint_Write_Control_Stream_LE(&LineEncoding, sizeof(CDC_LineEncoding_t));
Endpoint_ClearOUT();
}
break;
- case REQ_SetLineEncoding:
+ case CDC_REQ_SetLineEncoding:
if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
{
Endpoint_ClearSETUP();
/* Read the line coding data in from the host into the global struct */
- Endpoint_Read_Control_Stream_LE(&LineEncoding, sizeof(CDC_Line_Coding_t));
+ Endpoint_Read_Control_Stream_LE(&LineEncoding, sizeof(CDC_LineEncoding_t));
Endpoint_ClearIN();
}
{
LowByte = FetchNextCommandByte();
}
-
+
HighByte = !HighByte;
}
else
}
/* Fetch the next byte from the OUT endpoint */
- return Endpoint_Read_Byte();
+ return Endpoint_Read_8();
}
/** Writes the next response byte to the CDC data IN endpoint, and sends the endpoint back if needed to free up the
}
}
- /* Write the next byte to the OUT endpoint */
- Endpoint_Write_Byte(Response);
+ /* Write the next byte to the IN endpoint */
+ Endpoint_Write_8(Response);
}
/** Task to read in AVR910 commands from the CDC data OUT endpoint, process them, perform the required actions
* and send the appropriate response back to the host.
*/
-void CDC_Task(void)
+static void CDC_Task(void)
{
/* Select the OUT endpoint */
Endpoint_SelectEndpoint(CDC_RX_EPNUM);
if (Command == 'E')
{
RunBootloader = false;
-
+
/* Send confirmation byte back to the host */
WriteNextResponseByte('\r');
}
projects / pub / USBasp.git / blobdiff