Rewritten event system to remove all macros, to make user code clearer.

[pub/USBasp.git] / Demos / Device / CDC / CDC.c

diff --git a/Demos/Device/CDC/CDC.c b/Demos/Device/CDC/CDC.c
index fb7d74b..d7ebb9e 100644 (file)
--- a/Demos/Device/CDC/CDC.c
+++ b/Demos/Device/CDC/CDC.c
@@ -104,7 +104,7 @@ int main(void)
 /** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and\r
  *  starts the library USB task to begin the enumeration and USB management process.\r
  */\r
-EVENT_HANDLER(USB_Connect)\r
+void EVENT_USB_Connect(void)\r
 {\r
        /* Start USB management task */\r
        Scheduler_SetTaskMode(USB_USBTask, TASK_RUN);\r
@@ -116,7 +116,7 @@ EVENT_HANDLER(USB_Connect)
 /** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via\r
  *  the status LEDs and stops the USB management and CDC management tasks.\r
  */\r
-EVENT_HANDLER(USB_Disconnect)\r
+void EVENT_USB_Disconnect(void)\r
 {\r
        /* Stop running CDC and USB management tasks */\r
        Scheduler_SetTaskMode(CDC_Task, TASK_STOP);\r
@@ -129,7 +129,7 @@ EVENT_HANDLER(USB_Disconnect)
 /** Event handler for the USB_ConfigurationChanged event. This is fired when the host set the current configuration\r
  *  of the USB device after enumeration - the device endpoints are configured and the CDC management task started.\r
  */\r
-EVENT_HANDLER(USB_ConfigurationChanged)\r
+void EVENT_USB_ConfigurationChanged(void)\r
 {\r
        /* Setup CDC Notification, Rx and Tx Endpoints */\r
        Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT,\r
@@ -155,15 +155,15 @@ EVENT_HANDLER(USB_ConfigurationChanged)
  *  control requests that are not handled internally by the USB library (including the CDC control commands,\r
  *  which are all issued via the control endpoint), so that they can be handled appropriately for the application.\r
  */\r
-EVENT_HANDLER(USB_UnhandledControlPacket)\r
+void EVENT_USB_UnhandledControlPacket(void)\r
 {\r
        uint8_t* LineCodingData = (uint8_t*)&LineCoding;\r
 \r
        /* Process CDC specific control requests */\r
-       switch (bRequest)\r
+       switch (USB_ControlRequest.bRequest)\r
        {\r
                case REQ_GetLineEncoding:\r
-                       if (bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))\r
+                       if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))\r
                        {       \r
                                /* Acknowledge the SETUP packet, ready for data transfer */\r
                                Endpoint_ClearSETUP();\r
@@ -177,7 +177,7 @@ EVENT_HANDLER(USB_UnhandledControlPacket)
                        \r
                        break;\r
                case REQ_SetLineEncoding:\r
-                       if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))\r
+                       if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))\r
                        {\r
                                /* Acknowledge the SETUP packet, ready for data transfer */\r
                                Endpoint_ClearSETUP();\r
@@ -191,22 +191,16 @@ EVENT_HANDLER(USB_UnhandledControlPacket)
        \r
                        break;\r
                case REQ_SetControlLineState:\r
-                       if (bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))\r
+                       if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))\r
                        {\r
-#if 0\r
-                               /* NOTE: Here you can read in the line state mask from the host, to get the current state of the output handshake\r
-                                        lines. The mask is read in from the wValue parameter, and can be masked against the CONTROL_LINE_OUT_* masks\r
-                                        to determine the RTS and DTR line states using the following code:\r
-                               */\r
-\r
-                               uint16_t wIndex = Endpoint_Read_Word_LE();\r
-                                       \r
-                               // Do something with the given line states in wIndex\r
-#endif\r
-                               \r
                                /* Acknowledge the SETUP packet, ready for data transfer */\r
                                Endpoint_ClearSETUP();\r
                                \r
+                               /* NOTE: Here you can read in the line state mask from the host, to get the current state of the output handshake\r
+                                        lines. The mask is read in from the wValue parameter in USB_ControlRequest, and can be masked against the\r
+                                                CONTROL_LINE_OUT_* masks to determine the RTS and DTR line states using the following code:\r
+                               */\r
+                               \r
                                /* Acknowledge status stage */\r
                                while (!(Endpoint_IsINReady()));\r
                                Endpoint_ClearIN();\r