-/*\r
- LUFA Library\r
- Copyright (C) Dean Camera, 2010.\r
- \r
- dean [at] fourwalledcubicle [dot] com\r
- www.fourwalledcubicle.com\r
-*/\r
-\r
-/*\r
- Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)\r
-\r
- Permission to use, copy, modify, distribute, and sell this \r
- software and its documentation for any purpose is hereby granted\r
- without fee, provided that the above copyright notice appear in \r
- all copies and that both that the copyright notice and this\r
- permission notice and warranty disclaimer appear in supporting \r
- documentation, and that the name of the author not be used in \r
- advertising or publicity pertaining to distribution of the \r
- software without specific, written prior permission.\r
-\r
- The author disclaim all warranties with regard to this\r
- software, including all implied warranties of merchantability\r
- and fitness. In no event shall the author be liable for any\r
- special, indirect or consequential damages or any damages\r
- whatsoever resulting from loss of use, data or profits, whether\r
- in an action of contract, negligence or other tortious action,\r
- arising out of or in connection with the use or performance of\r
- this software.\r
-*/\r
-\r
-/** \file\r
- *\r
- * Main source file for the CDC class bootloader. This file contains the complete bootloader logic.\r
- */\r
- \r
-#define INCLUDE_FROM_BOOTLOADERCDC_C\r
-#include "BootloaderCDC.h"\r
-\r
-/** Line coding options for the virtual serial port. Although the virtual serial port data is never\r
- * sent through a physical serial port, the line encoding data must still be read and preserved from\r
- * the host, or the host will detect a problem and fail to open the port. This structure contains the\r
- * current encoding options, including baud rate, character format, parity mode and total number of \r
- * bits in each data chunk.\r
- */\r
-CDC_Line_Coding_t LineCoding = { .BaudRateBPS = 9600,\r
- .CharFormat = OneStopBit,\r
- .ParityType = Parity_None,\r
- .DataBits = 8 };\r
-\r
-/** Current address counter. This stores the current address of the FLASH or EEPROM as set by the host,\r
- * and is used when reading or writing to the AVRs memory (either FLASH or EEPROM depending on the issued\r
- * command.)\r
- */\r
-uint32_t CurrAddress;\r
-\r
-/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run\r
- * via a watchdog reset. When cleared the bootloader will exit, starting the watchdog and entering an infinite\r
- * loop until the AVR restarts and the application runs.\r
- */\r
-bool RunBootloader = true;\r
-\r
-\r
-/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously \r
- * runs the bootloader processing routine until instructed to soft-exit, or hard-reset via the watchdog to start\r
- * the loaded application code.\r
- */\r
-int main(void)\r
-{\r
- /* Setup hardware required for the bootloader */\r
- SetupHardware();\r
-\r
- /* Enable global interrupts so that the USB stack can function */\r
- sei();\r
-\r
- while (RunBootloader)\r
- {\r
- CDC_Task();\r
- USB_USBTask();\r
- }\r
- \r
- /* Disconnect from the host - USB interface will be reset later along with the AVR */\r
- USB_Detach();\r
-\r
- /* Enable the watchdog and force a timeout to reset the AVR */\r
- wdt_enable(WDTO_250MS);\r
-\r
- for (;;);\r
-}\r
-\r
-/** Configures all hardware required for the bootloader. */\r
-void SetupHardware(void)\r
-{\r
- /* Disable watchdog if enabled by bootloader/fuses */\r
- MCUSR &= ~(1 << WDRF);\r
- wdt_disable();\r
-\r
- /* Disable clock division */\r
- clock_prescale_set(clock_div_1);\r
- \r
- /* Relocate the interrupt vector table to the bootloader section */\r
- MCUCR = (1 << IVCE);\r
- MCUCR = (1 << IVSEL);\r
- \r
- /* Initialize USB Subsystem */\r
- USB_Init();\r
-}\r
-\r
-/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready\r
- * to relay data to and from the attached USB host.\r
- */\r
-void EVENT_USB_Device_ConfigurationChanged(void)\r
-{\r
- /* Setup CDC Notification, Rx and Tx Endpoints */\r
- Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT,\r
- ENDPOINT_DIR_IN, CDC_NOTIFICATION_EPSIZE,\r
- ENDPOINT_BANK_SINGLE);\r
-\r
- Endpoint_ConfigureEndpoint(CDC_TX_EPNUM, EP_TYPE_BULK,\r
- ENDPOINT_DIR_IN, CDC_TXRX_EPSIZE,\r
- ENDPOINT_BANK_SINGLE);\r
-\r
- Endpoint_ConfigureEndpoint(CDC_RX_EPNUM, EP_TYPE_BULK,\r
- ENDPOINT_DIR_OUT, CDC_TXRX_EPSIZE,\r
- ENDPOINT_BANK_SINGLE);\r
-}\r
-\r
-/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific\r
- * control requests that are not handled internally by the USB library, so that they can be handled appropriately\r
- * for the application.\r
- */\r
-void EVENT_USB_Device_UnhandledControlRequest(void)\r
-{\r
- uint8_t* LineCodingData = (uint8_t*)&LineCoding;\r
-\r
- /* Process CDC specific control requests */\r
- switch (USB_ControlRequest.bRequest)\r
- {\r
- case REQ_GetLineEncoding:\r
- if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))\r
- {\r
- Endpoint_ClearSETUP();\r
-\r
- for (uint8_t i = 0; i < sizeof(LineCoding); i++)\r
- Endpoint_Write_Byte(*(LineCodingData++)); \r
- \r
- Endpoint_ClearIN();\r
- \r
- Endpoint_ClearStatusStage();\r
- }\r
- \r
- break;\r
- case REQ_SetLineEncoding:\r
- if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))\r
- {\r
- Endpoint_ClearSETUP();\r
-\r
- while (!(Endpoint_IsOUTReceived()))\r
- { \r
- if (USB_DeviceState == DEVICE_STATE_Unattached)\r
- return;\r
- }\r
- \r
- for (uint8_t i = 0; i < sizeof(LineCoding); i++)\r
- *(LineCodingData++) = Endpoint_Read_Byte();\r
-\r
- Endpoint_ClearOUT();\r
-\r
- Endpoint_ClearStatusStage();\r
- }\r
- \r
- break;\r
- case REQ_SetControlLineState:\r
- if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))\r
- {\r
- Endpoint_ClearSETUP();\r
- \r
- Endpoint_ClearStatusStage();\r
- }\r
- \r
- break;\r
- }\r
-}\r
-\r
-/** Reads or writes a block of EEPROM or FLASH memory to or from the appropriate CDC data endpoint, depending\r
- * on the AVR910 protocol command issued.\r
- *\r
- * \param[in] Command Single character AVR910 protocol command indicating what memory operation to perform\r
- */\r
-static void ReadWriteMemoryBlock(const uint8_t Command)\r
-{\r
- uint16_t BlockSize;\r
- char MemoryType;\r
- \r
- bool HighByte = false;\r
- uint8_t LowByte = 0;\r
- \r
- BlockSize = (FetchNextCommandByte() << 8);\r
- BlockSize |= FetchNextCommandByte();\r
- \r
- MemoryType = FetchNextCommandByte();\r
-\r
- if ((MemoryType != 'E') && (MemoryType != 'F'))\r
- {\r
- /* Send error byte back to the host */\r
- WriteNextResponseByte('?');\r
- \r
- return;\r
- }\r
-\r
- /* Check if command is to read memory */\r
- if (Command == 'g')\r
- {\r
- /* Re-enable RWW section */\r
- boot_rww_enable();\r
-\r
- while (BlockSize--)\r
- {\r
- if (MemoryType == 'F')\r
- {\r
- /* Read the next FLASH byte from the current FLASH page */\r
- #if (FLASHEND > 0xFFFF)\r
- WriteNextResponseByte(pgm_read_byte_far(CurrAddress | HighByte));\r
- #else\r
- WriteNextResponseByte(pgm_read_byte(CurrAddress | HighByte)); \r
- #endif\r
- \r
- /* If both bytes in current word have been read, increment the address counter */\r
- if (HighByte)\r
- CurrAddress += 2;\r
- \r
- HighByte = !HighByte;\r
- }\r
- else\r
- {\r
- /* Read the next EEPROM byte into the endpoint */\r
- WriteNextResponseByte(eeprom_read_byte((uint8_t*)(uint16_t)(CurrAddress >> 1)));\r
-\r
- /* Increment the address counter after use */\r
- CurrAddress += 2;\r
- } \r
- }\r
- }\r
- else\r
- {\r
- uint32_t PageStartAddress = CurrAddress;\r
-\r
- if (MemoryType == 'F')\r
- {\r
- boot_page_erase(PageStartAddress);\r
- boot_spm_busy_wait();\r
- }\r
- \r
- while (BlockSize--)\r
- {\r
- if (MemoryType == 'F')\r
- { \r
- /* If both bytes in current word have been written, increment the address counter */\r
- if (HighByte)\r
- {\r
- /* Write the next FLASH word to the current FLASH page */\r
- boot_page_fill(CurrAddress, ((FetchNextCommandByte() << 8) | LowByte));\r
-\r
- /* Increment the address counter after use */\r
- CurrAddress += 2;\r
-\r
- HighByte = false;\r
- }\r
- else\r
- {\r
- LowByte = FetchNextCommandByte();\r
- \r
- HighByte = true;\r
- }\r
- }\r
- else\r
- {\r
- /* Write the next EEPROM byte from the endpoint */\r
- eeprom_write_byte((uint8_t*)(uint16_t)(CurrAddress >> 1), FetchNextCommandByte()); \r
-\r
- /* Increment the address counter after use */\r
- CurrAddress += 2;\r
- }\r
- }\r
-\r
- /* If in FLASH programming mode, commit the page after writing */\r
- if (MemoryType == 'F')\r
- {\r
- /* Commit the flash page to memory */\r
- boot_page_write(PageStartAddress);\r
- \r
- /* Wait until write operation has completed */\r
- boot_spm_busy_wait();\r
- }\r
- \r
- /* Send response byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
-}\r
-\r
-/** Retrieves the next byte from the host in the CDC data OUT endpoint, and clears the endpoint bank if needed\r
- * to allow reception of the next data packet from the host.\r
- *\r
- * \return Next received byte from the host in the CDC data OUT endpoint\r
- */\r
-static uint8_t FetchNextCommandByte(void)\r
-{\r
- /* Select the OUT endpoint so that the next data byte can be read */\r
- Endpoint_SelectEndpoint(CDC_RX_EPNUM);\r
- \r
- /* If OUT endpoint empty, clear it and wait for the next packet from the host */\r
- while (!(Endpoint_IsReadWriteAllowed()))\r
- {\r
- Endpoint_ClearOUT();\r
-\r
- while (!(Endpoint_IsOUTReceived()))\r
- {\r
- if (USB_DeviceState == DEVICE_STATE_Unattached)\r
- return 0;\r
- }\r
- }\r
- \r
- /* Fetch the next byte from the OUT endpoint */\r
- return Endpoint_Read_Byte();\r
-}\r
-\r
-/** Writes the next response byte to the CDC data IN endpoint, and sends the endpoint back if needed to free up the\r
- * bank when full ready for the next byte in the packet to the host.\r
- *\r
- * \param[in] Response Next response byte to send to the host\r
- */\r
-static void WriteNextResponseByte(const uint8_t Response)\r
-{\r
- /* Select the IN endpoint so that the next data byte can be written */\r
- Endpoint_SelectEndpoint(CDC_TX_EPNUM);\r
- \r
- /* If IN endpoint full, clear it and wait until ready for the next packet to the host */\r
- if (!(Endpoint_IsReadWriteAllowed()))\r
- {\r
- Endpoint_ClearIN();\r
- \r
- while (!(Endpoint_IsINReady()))\r
- { \r
- if (USB_DeviceState == DEVICE_STATE_Unattached)\r
- return;\r
- }\r
- }\r
- \r
- /* Write the next byte to the OUT endpoint */\r
- Endpoint_Write_Byte(Response);\r
-}\r
-\r
-/** Task to read in AVR910 commands from the CDC data OUT endpoint, process them, perform the required actions\r
- * and send the appropriate response back to the host.\r
- */\r
-void CDC_Task(void)\r
-{\r
- /* Select the OUT endpoint */\r
- Endpoint_SelectEndpoint(CDC_RX_EPNUM);\r
- \r
- /* Check if endpoint has a command in it sent from the host */\r
- if (Endpoint_IsOUTReceived())\r
- {\r
- /* Read in the bootloader command (first byte sent from host) */\r
- uint8_t Command = FetchNextCommandByte();\r
-\r
- if ((Command == 'L') || (Command == 'P') || (Command == 'T') || (Command == 'E'))\r
- {\r
- if (Command == 'E')\r
- RunBootloader = false;\r
- if (Command == 'T')\r
- FetchNextCommandByte();\r
-\r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
- else if (Command == 't')\r
- {\r
- /* Return ATMEGA128 part code - this is only to allow AVRProg to use the bootloader */\r
- WriteNextResponseByte(0x44);\r
-\r
- WriteNextResponseByte(0x00);\r
- }\r
- else if (Command == 'a')\r
- {\r
- /* Indicate auto-address increment is supported */\r
- WriteNextResponseByte('Y');\r
- }\r
- else if (Command == 'A')\r
- {\r
- /* Set the current address to that given by the host */\r
- CurrAddress = (FetchNextCommandByte() << 9);\r
- CurrAddress |= (FetchNextCommandByte() << 1);\r
-\r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r');\r
- }\r
- else if (Command == 'p')\r
- {\r
- /* Indicate serial programmer back to the host */\r
- WriteNextResponseByte('S'); \r
- }\r
- else if (Command == 'S')\r
- {\r
- /* Write the 7-byte software identifier to the endpoint */\r
- for (uint8_t CurrByte = 0; CurrByte < 7; CurrByte++)\r
- WriteNextResponseByte(SOFTWARE_IDENTIFIER[CurrByte]); \r
- }\r
- else if (Command == 'V')\r
- {\r
- WriteNextResponseByte('0' + BOOTLOADER_VERSION_MAJOR);\r
- WriteNextResponseByte('0' + BOOTLOADER_VERSION_MINOR);\r
- }\r
- else if (Command == 's')\r
- {\r
- WriteNextResponseByte(AVR_SIGNATURE_3); \r
- WriteNextResponseByte(AVR_SIGNATURE_2);\r
- WriteNextResponseByte(AVR_SIGNATURE_1);\r
- }\r
- else if (Command == 'b')\r
- {\r
- WriteNextResponseByte('Y');\r
- \r
- /* Send block size to the host */\r
- WriteNextResponseByte(SPM_PAGESIZE >> 8);\r
- WriteNextResponseByte(SPM_PAGESIZE & 0xFF); \r
- }\r
- else if (Command == 'e')\r
- {\r
- /* Clear the application section of flash */\r
- for (uint32_t CurrFlashAddress = 0; CurrFlashAddress < BOOT_START_ADDR; CurrFlashAddress++)\r
- {\r
- boot_page_erase(CurrFlashAddress);\r
- boot_spm_busy_wait();\r
- boot_page_write(CurrFlashAddress);\r
- boot_spm_busy_wait();\r
-\r
- CurrFlashAddress += SPM_PAGESIZE;\r
- }\r
- \r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
- else if (Command == 'l')\r
- {\r
- /* Set the lock bits to those given by the host */\r
- boot_lock_bits_set(FetchNextCommandByte());\r
-\r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r');\r
- }\r
- else if (Command == 'r')\r
- {\r
- WriteNextResponseByte(boot_lock_fuse_bits_get(GET_LOCK_BITS)); \r
- }\r
- else if (Command == 'F')\r
- {\r
- WriteNextResponseByte(boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS));\r
- }\r
- else if (Command == 'N')\r
- {\r
- WriteNextResponseByte(boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS)); \r
- }\r
- else if (Command == 'Q')\r
- {\r
- WriteNextResponseByte(boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS)); \r
- }\r
- else if (Command == 'C')\r
- { \r
- /* Write the high byte to the current flash page */\r
- boot_page_fill(CurrAddress, FetchNextCommandByte());\r
-\r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
- else if (Command == 'c')\r
- { \r
- /* Write the low byte to the current flash page */\r
- boot_page_fill(CurrAddress | 1, FetchNextCommandByte());\r
- \r
- /* Increment the address */\r
- CurrAddress += 2;\r
-\r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
- else if (Command == 'm')\r
- {\r
- /* Commit the flash page to memory */\r
- boot_page_write(CurrAddress);\r
- \r
- /* Wait until write operation has completed */\r
- boot_spm_busy_wait();\r
-\r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
- else if ((Command == 'B') || (Command == 'g'))\r
- {\r
- /* Delegate the block write/read to a separate function for clarity */\r
- ReadWriteMemoryBlock(Command);\r
- }\r
- else if (Command == 'R')\r
- {\r
- #if (FLASHEND > 0xFFFF)\r
- uint16_t ProgramWord = pgm_read_word_far(CurrAddress);\r
- #else\r
- uint16_t ProgramWord = pgm_read_word(CurrAddress); \r
- #endif\r
- \r
- WriteNextResponseByte(ProgramWord >> 8);\r
- WriteNextResponseByte(ProgramWord & 0xFF);\r
- }\r
- else if (Command == 'D')\r
- {\r
- /* Read the byte from the endpoint and write it to the EEPROM */\r
- eeprom_write_byte((uint8_t*)((uint16_t)(CurrAddress >> 1)), FetchNextCommandByte());\r
- \r
- /* Increment the address after use */ \r
- CurrAddress += 2;\r
- \r
- /* Send confirmation byte back to the host */\r
- WriteNextResponseByte('\r'); \r
- }\r
- else if (Command == 'd')\r
- {\r
- /* Read the EEPROM byte and write it to the endpoint */\r
- WriteNextResponseByte(eeprom_read_byte((uint8_t*)((uint16_t)(CurrAddress >> 1))));\r
-\r
- /* Increment the address after use */\r
- CurrAddress += 2;\r
- }\r
- else if (Command == 27)\r
- {\r
- /* Escape is sync, ignore */\r
- }\r
- else\r
- {\r
- /* Unknown command, return fail code */\r
- WriteNextResponseByte('?');\r
- }\r
-\r
- /* Select the IN endpoint */\r
- Endpoint_SelectEndpoint(CDC_TX_EPNUM);\r
-\r
- /* Remember if the endpoint is completely full before clearing it */\r
- bool IsEndpointFull = !(Endpoint_IsReadWriteAllowed());\r
-\r
- /* Send the endpoint data to the host */\r
- Endpoint_ClearIN();\r
- \r
- /* If a full endpoint's worth of data was sent, we need to send an empty packet afterwards to signal end of transfer */\r
- if (IsEndpointFull)\r
- {\r
- while (!(Endpoint_IsINReady()))\r
- { \r
- if (USB_DeviceState == DEVICE_STATE_Unattached)\r
- return;\r
- }\r
-\r
- Endpoint_ClearIN();\r
- }\r
-\r
- /* Wait until the data has been sent to the host */\r
- while (!(Endpoint_IsINReady()))\r
- { \r
- if (USB_DeviceState == DEVICE_STATE_Unattached)\r
- return;\r
- }\r
- \r
- /* Select the OUT endpoint */\r
- Endpoint_SelectEndpoint(CDC_RX_EPNUM);\r
-\r
- /* Acknowledge the command from the host */\r
- Endpoint_ClearOUT();\r
- }\r
-}\r
+/*
+ LUFA Library
+ Copyright (C) Dean Camera, 2010.
+
+ dean [at] fourwalledcubicle [dot] com
+ www.fourwalledcubicle.com
+*/
+
+/*
+ Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
+
+ Permission to use, copy, modify, distribute, and sell this
+ software and its documentation for any purpose is hereby granted
+ without fee, provided that the above copyright notice appear in
+ all copies and that both that the copyright notice and this
+ permission notice and warranty disclaimer appear in supporting
+ documentation, and that the name of the author not be used in
+ advertising or publicity pertaining to distribution of the
+ software without specific, written prior permission.
+
+ The author disclaim all warranties with regard to this
+ software, including all implied warranties of merchantability
+ and fitness. In no event shall the author be liable for any
+ special, indirect or consequential damages or any damages
+ whatsoever resulting from loss of use, data or profits, whether
+ in an action of contract, negligence or other tortious action,
+ arising out of or in connection with the use or performance of
+ this software.
+*/
+
+/** \file
+ *
+ * Main source file for the CDC class bootloader. This file contains the complete bootloader logic.
+ */
+
+#define INCLUDE_FROM_BOOTLOADERCDC_C
+#include "BootloaderCDC.h"
+
+/** Line coding options for the virtual serial port. Although the virtual serial port data is never
+ * sent through a physical serial port, the line encoding data must still be read and preserved from
+ * the host, or the host will detect a problem and fail to open the port. This structure contains the
+ * current encoding options, including baud rate, character format, parity mode and total number of
+ * bits in each data chunk.
+ */
+CDC_Line_Coding_t LineCoding = { .BaudRateBPS = 9600,
+ .CharFormat = OneStopBit,
+ .ParityType = Parity_None,
+ .DataBits = 8 };
+
+/** Current address counter. This stores the current address of the FLASH or EEPROM as set by the host,
+ * and is used when reading or writing to the AVRs memory (either FLASH or EEPROM depending on the issued
+ * command.)
+ */
+uint32_t CurrAddress;
+
+/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
+ * via a watchdog reset. When cleared the bootloader will exit, starting the watchdog and entering an infinite
+ * loop until the AVR restarts and the application runs.
+ */
+bool RunBootloader = true;
+
+
+/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
+ * runs the bootloader processing routine until instructed to soft-exit, or hard-reset via the watchdog to start
+ * the loaded application code.
+ */
+int main(void)
+{
+ /* Setup hardware required for the bootloader */
+ SetupHardware();
+
+ /* Enable global interrupts so that the USB stack can function */
+ sei();
+
+ while (RunBootloader)
+ {
+ CDC_Task();
+ USB_USBTask();
+ }
+
+ /* Disconnect from the host - USB interface will be reset later along with the AVR */
+ USB_Detach();
+
+ /* Enable the watchdog and force a timeout to reset the AVR */
+ wdt_enable(WDTO_250MS);
+
+ for (;;);
+}
+
+/** Configures all hardware required for the bootloader. */
+void SetupHardware(void)
+{
+ /* Disable watchdog if enabled by bootloader/fuses */
+ MCUSR &= ~(1 << WDRF);
+ wdt_disable();
+
+ /* Disable clock division */
+ clock_prescale_set(clock_div_1);
+
+ /* Relocate the interrupt vector table to the bootloader section */
+ MCUCR = (1 << IVCE);
+ MCUCR = (1 << IVSEL);
+
+ /* Initialize USB Subsystem */
+ USB_Init();
+}
+
+/** Event handler for the USB_ConfigurationChanged event. This configures the device's endpoints ready
+ * to relay data to and from the attached USB host.
+ */
+void EVENT_USB_Device_ConfigurationChanged(void)
+{
+ /* Setup CDC Notification, Rx and Tx Endpoints */
+ Endpoint_ConfigureEndpoint(CDC_NOTIFICATION_EPNUM, EP_TYPE_INTERRUPT,
+ ENDPOINT_DIR_IN, CDC_NOTIFICATION_EPSIZE,
+ ENDPOINT_BANK_SINGLE);
+
+ Endpoint_ConfigureEndpoint(CDC_TX_EPNUM, EP_TYPE_BULK,
+ ENDPOINT_DIR_IN, CDC_TXRX_EPSIZE,
+ ENDPOINT_BANK_SINGLE);
+
+ Endpoint_ConfigureEndpoint(CDC_RX_EPNUM, EP_TYPE_BULK,
+ ENDPOINT_DIR_OUT, CDC_TXRX_EPSIZE,
+ ENDPOINT_BANK_SINGLE);
+}
+
+/** Event handler for the USB_UnhandledControlRequest event. This is used to catch standard and class specific
+ * control requests that are not handled internally by the USB library, so that they can be handled appropriately
+ * for the application.
+ */
+void EVENT_USB_Device_UnhandledControlRequest(void)
+{
+ uint8_t* LineCodingData = (uint8_t*)&LineCoding;
+
+ /* Process CDC specific control requests */
+ switch (USB_ControlRequest.bRequest)
+ {
+ case REQ_GetLineEncoding:
+ if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
+ {
+ Endpoint_ClearSETUP();
+
+ for (uint8_t i = 0; i < sizeof(LineCoding); i++)
+ Endpoint_Write_Byte(*(LineCodingData++));
+
+ Endpoint_ClearIN();
+
+ Endpoint_ClearStatusStage();
+ }
+
+ break;
+ case REQ_SetLineEncoding:
+ if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
+ {
+ Endpoint_ClearSETUP();
+
+ while (!(Endpoint_IsOUTReceived()))
+ {
+ if (USB_DeviceState == DEVICE_STATE_Unattached)
+ return;
+ }
+
+ for (uint8_t i = 0; i < sizeof(LineCoding); i++)
+ *(LineCodingData++) = Endpoint_Read_Byte();
+
+ Endpoint_ClearOUT();
+
+ Endpoint_ClearStatusStage();
+ }
+
+ break;
+ case REQ_SetControlLineState:
+ if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
+ {
+ Endpoint_ClearSETUP();
+
+ Endpoint_ClearStatusStage();
+ }
+
+ break;
+ }
+}
+
+/** Reads or writes a block of EEPROM or FLASH memory to or from the appropriate CDC data endpoint, depending
+ * on the AVR910 protocol command issued.
+ *
+ * \param[in] Command Single character AVR910 protocol command indicating what memory operation to perform
+ */
+static void ReadWriteMemoryBlock(const uint8_t Command)
+{
+ uint16_t BlockSize;
+ char MemoryType;
+
+ bool HighByte = false;
+ uint8_t LowByte = 0;
+
+ BlockSize = (FetchNextCommandByte() << 8);
+ BlockSize |= FetchNextCommandByte();
+
+ MemoryType = FetchNextCommandByte();
+
+ if ((MemoryType != 'E') && (MemoryType != 'F'))
+ {
+ /* Send error byte back to the host */
+ WriteNextResponseByte('?');
+
+ return;
+ }
+
+ /* Check if command is to read memory */
+ if (Command == 'g')
+ {
+ /* Re-enable RWW section */
+ boot_rww_enable();
+
+ while (BlockSize--)
+ {
+ if (MemoryType == 'F')
+ {
+ /* Read the next FLASH byte from the current FLASH page */
+ #if (FLASHEND > 0xFFFF)
+ WriteNextResponseByte(pgm_read_byte_far(CurrAddress | HighByte));
+ #else
+ WriteNextResponseByte(pgm_read_byte(CurrAddress | HighByte));
+ #endif
+
+ /* If both bytes in current word have been read, increment the address counter */
+ if (HighByte)
+ CurrAddress += 2;
+
+ HighByte = !HighByte;
+ }
+ else
+ {
+ /* Read the next EEPROM byte into the endpoint */
+ WriteNextResponseByte(eeprom_read_byte((uint8_t*)(uint16_t)(CurrAddress >> 1)));
+
+ /* Increment the address counter after use */
+ CurrAddress += 2;
+ }
+ }
+ }
+ else
+ {
+ uint32_t PageStartAddress = CurrAddress;
+
+ if (MemoryType == 'F')
+ {
+ boot_page_erase(PageStartAddress);
+ boot_spm_busy_wait();
+ }
+
+ while (BlockSize--)
+ {
+ if (MemoryType == 'F')
+ {
+ /* If both bytes in current word have been written, increment the address counter */
+ if (HighByte)
+ {
+ /* Write the next FLASH word to the current FLASH page */
+ boot_page_fill(CurrAddress, ((FetchNextCommandByte() << 8) | LowByte));
+
+ /* Increment the address counter after use */
+ CurrAddress += 2;
+
+ HighByte = false;
+ }
+ else
+ {
+ LowByte = FetchNextCommandByte();
+
+ HighByte = true;
+ }
+ }
+ else
+ {
+ /* Write the next EEPROM byte from the endpoint */
+ eeprom_write_byte((uint8_t*)(uint16_t)(CurrAddress >> 1), FetchNextCommandByte());
+
+ /* Increment the address counter after use */
+ CurrAddress += 2;
+ }
+ }
+
+ /* If in FLASH programming mode, commit the page after writing */
+ if (MemoryType == 'F')
+ {
+ /* Commit the flash page to memory */
+ boot_page_write(PageStartAddress);
+
+ /* Wait until write operation has completed */
+ boot_spm_busy_wait();
+ }
+
+ /* Send response byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+}
+
+/** Retrieves the next byte from the host in the CDC data OUT endpoint, and clears the endpoint bank if needed
+ * to allow reception of the next data packet from the host.
+ *
+ * \return Next received byte from the host in the CDC data OUT endpoint
+ */
+static uint8_t FetchNextCommandByte(void)
+{
+ /* Select the OUT endpoint so that the next data byte can be read */
+ Endpoint_SelectEndpoint(CDC_RX_EPNUM);
+
+ /* If OUT endpoint empty, clear it and wait for the next packet from the host */
+ while (!(Endpoint_IsReadWriteAllowed()))
+ {
+ Endpoint_ClearOUT();
+
+ while (!(Endpoint_IsOUTReceived()))
+ {
+ if (USB_DeviceState == DEVICE_STATE_Unattached)
+ return 0;
+ }
+ }
+
+ /* Fetch the next byte from the OUT endpoint */
+ return Endpoint_Read_Byte();
+}
+
+/** Writes the next response byte to the CDC data IN endpoint, and sends the endpoint back if needed to free up the
+ * bank when full ready for the next byte in the packet to the host.
+ *
+ * \param[in] Response Next response byte to send to the host
+ */
+static void WriteNextResponseByte(const uint8_t Response)
+{
+ /* Select the IN endpoint so that the next data byte can be written */
+ Endpoint_SelectEndpoint(CDC_TX_EPNUM);
+
+ /* If IN endpoint full, clear it and wait until ready for the next packet to the host */
+ if (!(Endpoint_IsReadWriteAllowed()))
+ {
+ Endpoint_ClearIN();
+
+ while (!(Endpoint_IsINReady()))
+ {
+ if (USB_DeviceState == DEVICE_STATE_Unattached)
+ return;
+ }
+ }
+
+ /* Write the next byte to the OUT endpoint */
+ Endpoint_Write_Byte(Response);
+}
+
+/** Task to read in AVR910 commands from the CDC data OUT endpoint, process them, perform the required actions
+ * and send the appropriate response back to the host.
+ */
+void CDC_Task(void)
+{
+ /* Select the OUT endpoint */
+ Endpoint_SelectEndpoint(CDC_RX_EPNUM);
+
+ /* Check if endpoint has a command in it sent from the host */
+ if (Endpoint_IsOUTReceived())
+ {
+ /* Read in the bootloader command (first byte sent from host) */
+ uint8_t Command = FetchNextCommandByte();
+
+ if ((Command == 'L') || (Command == 'P') || (Command == 'T') || (Command == 'E'))
+ {
+ if (Command == 'E')
+ RunBootloader = false;
+ if (Command == 'T')
+ FetchNextCommandByte();
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 't')
+ {
+ /* Return ATMEGA128 part code - this is only to allow AVRProg to use the bootloader */
+ WriteNextResponseByte(0x44);
+
+ WriteNextResponseByte(0x00);
+ }
+ else if (Command == 'a')
+ {
+ /* Indicate auto-address increment is supported */
+ WriteNextResponseByte('Y');
+ }
+ else if (Command == 'A')
+ {
+ /* Set the current address to that given by the host */
+ CurrAddress = (FetchNextCommandByte() << 9);
+ CurrAddress |= (FetchNextCommandByte() << 1);
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 'p')
+ {
+ /* Indicate serial programmer back to the host */
+ WriteNextResponseByte('S');
+ }
+ else if (Command == 'S')
+ {
+ /* Write the 7-byte software identifier to the endpoint */
+ for (uint8_t CurrByte = 0; CurrByte < 7; CurrByte++)
+ WriteNextResponseByte(SOFTWARE_IDENTIFIER[CurrByte]);
+ }
+ else if (Command == 'V')
+ {
+ WriteNextResponseByte('0' + BOOTLOADER_VERSION_MAJOR);
+ WriteNextResponseByte('0' + BOOTLOADER_VERSION_MINOR);
+ }
+ else if (Command == 's')
+ {
+ WriteNextResponseByte(AVR_SIGNATURE_3);
+ WriteNextResponseByte(AVR_SIGNATURE_2);
+ WriteNextResponseByte(AVR_SIGNATURE_1);
+ }
+ else if (Command == 'b')
+ {
+ WriteNextResponseByte('Y');
+
+ /* Send block size to the host */
+ WriteNextResponseByte(SPM_PAGESIZE >> 8);
+ WriteNextResponseByte(SPM_PAGESIZE & 0xFF);
+ }
+ else if (Command == 'e')
+ {
+ /* Clear the application section of flash */
+ for (uint32_t CurrFlashAddress = 0; CurrFlashAddress < BOOT_START_ADDR; CurrFlashAddress++)
+ {
+ boot_page_erase(CurrFlashAddress);
+ boot_spm_busy_wait();
+ boot_page_write(CurrFlashAddress);
+ boot_spm_busy_wait();
+
+ CurrFlashAddress += SPM_PAGESIZE;
+ }
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 'l')
+ {
+ /* Set the lock bits to those given by the host */
+ boot_lock_bits_set(FetchNextCommandByte());
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 'r')
+ {
+ WriteNextResponseByte(boot_lock_fuse_bits_get(GET_LOCK_BITS));
+ }
+ else if (Command == 'F')
+ {
+ WriteNextResponseByte(boot_lock_fuse_bits_get(GET_LOW_FUSE_BITS));
+ }
+ else if (Command == 'N')
+ {
+ WriteNextResponseByte(boot_lock_fuse_bits_get(GET_HIGH_FUSE_BITS));
+ }
+ else if (Command == 'Q')
+ {
+ WriteNextResponseByte(boot_lock_fuse_bits_get(GET_EXTENDED_FUSE_BITS));
+ }
+ else if (Command == 'C')
+ {
+ /* Write the high byte to the current flash page */
+ boot_page_fill(CurrAddress, FetchNextCommandByte());
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 'c')
+ {
+ /* Write the low byte to the current flash page */
+ boot_page_fill(CurrAddress | 1, FetchNextCommandByte());
+
+ /* Increment the address */
+ CurrAddress += 2;
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 'm')
+ {
+ /* Commit the flash page to memory */
+ boot_page_write(CurrAddress);
+
+ /* Wait until write operation has completed */
+ boot_spm_busy_wait();
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if ((Command == 'B') || (Command == 'g'))
+ {
+ /* Delegate the block write/read to a separate function for clarity */
+ ReadWriteMemoryBlock(Command);
+ }
+ else if (Command == 'R')
+ {
+ #if (FLASHEND > 0xFFFF)
+ uint16_t ProgramWord = pgm_read_word_far(CurrAddress);
+ #else
+ uint16_t ProgramWord = pgm_read_word(CurrAddress);
+ #endif
+
+ WriteNextResponseByte(ProgramWord >> 8);
+ WriteNextResponseByte(ProgramWord & 0xFF);
+ }
+ else if (Command == 'D')
+ {
+ /* Read the byte from the endpoint and write it to the EEPROM */
+ eeprom_write_byte((uint8_t*)((uint16_t)(CurrAddress >> 1)), FetchNextCommandByte());
+
+ /* Increment the address after use */
+ CurrAddress += 2;
+
+ /* Send confirmation byte back to the host */
+ WriteNextResponseByte('\r');
+ }
+ else if (Command == 'd')
+ {
+ /* Read the EEPROM byte and write it to the endpoint */
+ WriteNextResponseByte(eeprom_read_byte((uint8_t*)((uint16_t)(CurrAddress >> 1))));
+
+ /* Increment the address after use */
+ CurrAddress += 2;
+ }
+ else if (Command == 27)
+ {
+ /* Escape is sync, ignore */
+ }
+ else
+ {
+ /* Unknown command, return fail code */
+ WriteNextResponseByte('?');
+ }
+
+ /* Select the IN endpoint */
+ Endpoint_SelectEndpoint(CDC_TX_EPNUM);
+
+ /* Remember if the endpoint is completely full before clearing it */
+ bool IsEndpointFull = !(Endpoint_IsReadWriteAllowed());
+
+ /* Send the endpoint data to the host */
+ Endpoint_ClearIN();
+
+ /* If a full endpoint's worth of data was sent, we need to send an empty packet afterwards to signal end of transfer */
+ if (IsEndpointFull)
+ {
+ while (!(Endpoint_IsINReady()))
+ {
+ if (USB_DeviceState == DEVICE_STATE_Unattached)
+ return;
+ }
+
+ Endpoint_ClearIN();
+ }
+
+ /* Wait until the data has been sent to the host */
+ while (!(Endpoint_IsINReady()))
+ {
+ if (USB_DeviceState == DEVICE_STATE_Unattached)
+ return;
+ }
+
+ /* Select the OUT endpoint */
+ Endpoint_SelectEndpoint(CDC_RX_EPNUM);
+
+ /* Acknowledge the command from the host */
+ Endpoint_ClearOUT();
+ }
+}
projects / pub / USBasp.git / blobdiff