/*
LUFA Library
- Copyright (C) Dean Camera, 2011.
+ Copyright (C) Dean Camera, 2018.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
- Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
+ Copyright 2018 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
- The author disclaim all warranties with regard to this
+ The author disclaims all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
/** \ingroup Group_TWI
* \defgroup Group_TWI_AVR8 TWI Peripheral Driver (AVR8)
*
- * \section Sec_ModDescription Module Description
+ * \section Sec_TWI_AVR8_ModDescription Module Description
* Master mode TWI driver for the 8-bit AVR microcontrollers which contain a hardware TWI module.
*
* \note This file should not be included directly. It is automatically included as needed by the TWI driver
* dispatch header located in LUFA/Drivers/Peripheral/TWI.h.
*
- * \section Sec_ExampleUsage Example Usage
+ * \section Sec_TWI_AVR8_ExampleUsage Example Usage
* The following snippet is an example of how this module may be used within a typical
* application.
*
* <b>Low Level API Example:</b>
* \code
- * // Initialize the TWI driver before first use
- * TWI_Init(TWI_BIT_PRESCALE_1, 10);
+ * // Initialize the TWI driver before first use at 200KHz
+ * TWI_Init(TWI_BIT_PRESCALE_1, TWI_BITLENGTH_FROM_FREQ(1, 200000));
*
* // Start a write session to device at device address 0xA0, internal address 0xDC with a 10ms timeout
* if (TWI_StartTransmission(0xA0 | TWI_ADDRESS_WRITE, 10) == TWI_ERROR_NoError)
* }
* }
* \endcode
- *
+ *
* <b>High Level API Example:</b>
* \code
- * // Initialize the TWI driver before first use
- * TWI_Init(TWI_BIT_PRESCALE_1, 10);
+ * // Initialize the TWI driver before first use at 200KHz
+ * TWI_Init(TWI_BIT_PRESCALE_1, TWI_BITLENGTH_FROM_FREQ(1, 200000));
*
* // Start a write session to device at device address 0xA0, internal address 0xDC with a 10ms timeout
* uint8_t InternalWriteAddress = 0xDC;
* uint8_t WritePacket[3] = {0x01, 0x02, 0x03};
*
* TWI_WritePacket(0xA0, 10, &InternalWriteAddress, sizeof(InternalWriteAddress),
- * WritePacket, sizeof(WritePacket);
+ * &WritePacket, sizeof(WritePacket);
*
* // Start a read session to device at address 0xA0, internal address 0xDC with a 10ms timeout
* uint8_t InternalReadAddress = 0xDC;
* uint8_t ReadPacket[3];
*
* TWI_ReadPacket(0xA0, 10, &InternalReadAddress, sizeof(InternalReadAddress),
- * ReadPacket, sizeof(ReadPacket);
+ * &ReadPacket, sizeof(ReadPacket);
* \endcode
*
* @{
#if !(defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB646__) || \
defined(__AVR_AT90USB1287__) || defined(__AVR_AT90USB647__) || \
- defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__) || \
- defined(__AVR_ATmega32U6__))
+ defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__))
#error The TWI peripheral driver is not currently available for your selected microcontroller model.
#endif
* or \ref TWI_ADDRESS_WRITE to obtain the device's read and write address respectively.
*/
#define TWI_DEVICE_ADDRESS_MASK 0xFE
-
+
/** Bit length prescaler for \ref TWI_Init(). This mask multiplies the TWI bit length prescaler by 1. */
#define TWI_BIT_PRESCALE_1 ((0 << TWPS1) | (0 << TWPS0))
-
+
/** Bit length prescaler for \ref TWI_Init(). This mask multiplies the TWI bit length prescaler by 4. */
#define TWI_BIT_PRESCALE_4 ((0 << TWPS1) | (1 << TWPS0))
/** Bit length prescaler for \ref TWI_Init(). This mask multiplies the TWI bit length prescaler by 64. */
#define TWI_BIT_PRESCALE_64 ((1 << TWPS1) | (1 << TWPS0))
-
+
+ /** Calculates the length of each bit on the TWI bus for a given target frequency. This may be used with
+ * the \ref TWI_Init() function to convert a bus frequency to a number of clocks for the \c BitLength
+ * parameter.
+ *
+ * \param[in] Prescale Prescaler set on the TWI bus.
+ * \param[in] Frequency Desired TWI bus frequency in Hz.
+ *
+ * \return Bit length in clocks for the given TWI bus frequency at the given prescaler value.
+ */
+ #define TWI_BITLENGTH_FROM_FREQ(Prescale, Frequency) ((((F_CPU / (Prescale)) / (Frequency)) - 16) / 2)
+
/* Enums: */
/** Enum for the possible return codes of the TWI transfer start routine and other dependant TWI functions. */
enum TWI_ErrorCodes_t
TWI_ERROR_SlaveNotReady = 4, /**< Slave NAKed the TWI bus START condition. */
TWI_ERROR_SlaveNAK = 5, /**< Slave NAKed whilst attempting to send data to the device. */
};
-
+
/* Inline Functions: */
/** Initializes the TWI hardware into master mode, ready for data transmission and reception. This must be
* before any other TWI operations.
*
* The generated SCL frequency will be according to the formula <pre>F_CPU / (16 + 2 * BitLength + 4 ^ Prescale)</pre>.
*
- * \note The value of the \c BitLength parameter should not be set below 10 or invalid bus conditions may
- * occur, as indicated in the AVR8 microcontroller datasheet.
+ * \attention The value of the \c BitLength parameter should not be set below 10 or invalid bus conditions may
+ * occur, as indicated in the AVR8 microcontroller datasheet.
*
* \param[in] Prescale Prescaler to use when determining the bus frequency, a \c TWI_BIT_PRESCALE_* value.
* \param[in] BitLength Length of the bits sent on the bus.
*/
- static inline void TWI_Init(const uint8_t Prescale, const uint8_t BitLength) ATTR_ALWAYS_INLINE;
- static inline void TWI_Init(const uint8_t Prescale, const uint8_t BitLength)
+ static inline void TWI_Init(const uint8_t Prescale,
+ const uint8_t BitLength) ATTR_ALWAYS_INLINE;
+ static inline void TWI_Init(const uint8_t Prescale,
+ const uint8_t BitLength)
{
TWCR |= (1 << TWEN);
TWSR = Prescale;
TWCR = ((1 << TWINT) | (1 << TWSTO) | (1 << TWEN));
}
+ /* Function Prototypes: */
+ /** Begins a master mode TWI bus communication with the given slave device address.
+ *
+ * \param[in] SlaveAddress Address of the slave TWI device to communicate with.
+ * \param[in] TimeoutMS Timeout period within which the slave must respond, in milliseconds.
+ *
+ * \return A value from the \ref TWI_ErrorCodes_t enum.
+ */
+ uint8_t TWI_StartTransmission(const uint8_t SlaveAddress,
+ const uint8_t TimeoutMS);
+
/** Sends a byte to the currently addressed device on the TWI bus.
*
* \param[in] Byte Byte to send to the currently addressed device
*
* \return Boolean \c true if the recipient ACKed the byte, \c false otherwise
*/
- static inline bool TWI_SendByte(const uint8_t Byte)
- {
- TWDR = Byte;
- TWCR = ((1 << TWINT) | (1 << TWEN));
- while (!(TWCR & (1 << TWINT)));
-
- return ((TWSR & TW_STATUS_MASK) == TW_MT_DATA_ACK);
- }
+ bool TWI_SendByte(const uint8_t Byte);
/** Receives a byte from the currently addressed device on the TWI bus.
*
*
* \return Boolean \c true if the byte reception successfully completed, \c false otherwise.
*/
- static inline bool TWI_ReceiveByte(uint8_t* const Byte,
- const bool LastByte)
- {
- uint8_t TWCRMask = ((1 << TWINT) | (1 << TWEN));
-
- if (!(LastByte))
- TWCRMask |= (1 << TWEA);
-
- TWCR = TWCRMask;
- while (!(TWCR & (1 << TWINT)));
- *Byte = TWDR;
-
- return ((TWSR & TW_STATUS_MASK) == TW_MR_DATA_ACK);
- }
-
- /* Function Prototypes: */
- /** Begins a master mode TWI bus communication with the given slave device address.
- *
- * \param[in] SlaveAddress Address of the slave TWI device to communicate with.
- * \param[in] TimeoutMS Timeout period within which the slave must respond, in milliseconds.
- *
- * \return A value from the \ref TWI_ErrorCodes_t enum.
- */
- uint8_t TWI_StartTransmission(const uint8_t SlaveAddress,
- const uint8_t TimeoutMS);
+ bool TWI_ReceiveByte(uint8_t* const Byte,
+ const bool LastByte) ATTR_NON_NULL_PTR_ARG(1);
/** High level function to perform a complete packet transfer over the TWI bus to the specified
* device.
uint8_t TWI_ReadPacket(const uint8_t SlaveAddress,
const uint8_t TimeoutMS,
const uint8_t* InternalAddress,
- const uint8_t InternalAddressLen,
+ uint8_t InternalAddressLen,
uint8_t* Buffer,
- uint8_t Length) ATTR_NON_NULL_PTR_ARG(3);
+ uint16_t Length) ATTR_NON_NULL_PTR_ARG(3);
/** High level function to perform a complete packet transfer over the TWI bus from the specified
* device.
const uint8_t* InternalAddress,
uint8_t InternalAddressLen,
const uint8_t* Buffer,
- uint8_t Length) ATTR_NON_NULL_PTR_ARG(3);
+ uint16_t Length) ATTR_NON_NULL_PTR_ARG(3);
/* Disable C linkage for C++ Compilers: */
#if defined(__cplusplus)
projects / pub / USBasp.git / blobdiff