/*
LUFA Library
- Copyright (C) Dean Camera, 2010.
+ Copyright (C) Dean Camera, 2012.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
- Copyright 2010 Dean Camera (dean [at] fourwalledcubicle [dot] com)
+ Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com)
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
static void XMEGANVM_SendAddress(const uint32_t AbsoluteAddress)
{
/* Send the given 32-bit address to the target, LSB first */
- XPROGTarget_SendByte(((uint8_t*)&AbsoluteAddress)[0]);
- XPROGTarget_SendByte(((uint8_t*)&AbsoluteAddress)[1]);
- XPROGTarget_SendByte(((uint8_t*)&AbsoluteAddress)[2]);
- XPROGTarget_SendByte(((uint8_t*)&AbsoluteAddress)[3]);
+ XPROGTarget_SendByte(AbsoluteAddress & 0xFF);
+ XPROGTarget_SendByte(AbsoluteAddress >> 8);
+ XPROGTarget_SendByte(AbsoluteAddress >> 16);
+ XPROGTarget_SendByte(AbsoluteAddress >> 24);
}
/** Sends the given NVM register address to the target.
{
/* Fetch the current status value via the pointer register (without auto-increment afterwards) */
XPROGTarget_SendByte(PDI_CMD_LD | (PDI_POINTER_INDIRECT << 2) | PDI_DATSIZE_1BYTE);
+
uint8_t StatusRegister = XPROGTarget_ReceiveByte();
/* We might have timed out waiting for the status register read response, check here */
}
}
+/** Enables the physical PDI interface on the target and enables access to the internal NVM controller.
+ *
+ * \return Boolean true if the PDI interface was enabled successfully, false otherwise
+ */
+bool XMEGANVM_EnablePDI(void)
+{
+ /* Enable PDI programming mode with the attached target */
+ XPROGTarget_EnableTargetPDI();
+
+ /* Store the RESET key into the RESET PDI register to keep the XMEGA in reset */
+ XPROGTarget_SendByte(PDI_CMD_STCS | PDI_RESET_REG);
+ XPROGTarget_SendByte(PDI_RESET_KEY);
+
+ /* Lower direction change guard time to 32 USART bits */
+ XPROGTarget_SendByte(PDI_CMD_STCS | PDI_CTRL_REG);
+ XPROGTarget_SendByte(0x02);
+
+ /* Enable access to the XPROG NVM bus by sending the documented NVM access key to the device */
+ XPROGTarget_SendByte(PDI_CMD_KEY);
+ for (uint8_t i = sizeof(PDI_NVMENABLE_KEY); i > 0; i--)
+ XPROGTarget_SendByte(PDI_NVMENABLE_KEY[i - 1]);
+
+ /* Wait until the NVM bus becomes active */
+ return XMEGANVM_WaitWhileNVMBusBusy();
+}
+
+/** Removes access to the target's NVM controller and physically disables the target's physical PDI interface. */
+void XMEGANVM_DisablePDI(void)
+{
+ XMEGANVM_WaitWhileNVMBusBusy();
+
+ /* Clear the RESET key in the RESET PDI register to allow the XMEGA to run - must perform this until the
+ * change takes effect, as in some cases it takes multiple writes (silicon bug?).
+ */
+ do
+ {
+ /* Clear reset register */
+ XPROGTarget_SendByte(PDI_CMD_STCS | PDI_RESET_REG);
+ XPROGTarget_SendByte(0x00);
+
+ /* Read back the reset register, check to see if it took effect */
+ XPROGTarget_SendByte(PDI_CMD_LDCS | PDI_RESET_REG);
+ } while (XPROGTarget_ReceiveByte() != 0x00);
+
+ XPROGTarget_DisableTargetPDI();
+}
+
/** Retrieves the CRC value of the given memory space.
*
* \param[in] CRCCommand NVM CRC command to issue to the target
*/
bool XMEGANVM_GetMemoryCRC(const uint8_t CRCCommand, uint32_t* const CRCDest)
{
+ *CRCDest = 0;
+
/* Wait until the NVM controller is no longer busy */
if (!(XMEGANVM_WaitWhileNVMControllerBusy()))
return false;
/* Set CMDEX bit in NVM CTRLA register to start the CRC generation */
XPROGTarget_SendByte(PDI_CMD_STS | (PDI_DATSIZE_4BYTES << 2));
XMEGANVM_SendNVMRegAddress(XMEGA_NVM_REG_CTRLA);
- XPROGTarget_SendByte(1 << 0);
+ XPROGTarget_SendByte(XMEGA_NVM_BIT_CTRLA_CMDEX);
/* Wait until the NVM bus is ready again */
if (!(XMEGANVM_WaitWhileNVMBusBusy()))
/* Send the REPEAT command to grab the CRC bytes */
XPROGTarget_SendByte(PDI_CMD_REPEAT | PDI_DATSIZE_1BYTE);
- XPROGTarget_SendByte(XMEGA_CRC_LENGTH - 1);
+ XPROGTarget_SendByte(XMEGA_CRC_LENGTH_BYTES - 1);
/* Read in the CRC bytes from the target */
XPROGTarget_SendByte(PDI_CMD_LD | (PDI_POINTER_INDIRECT_PI << 2) | PDI_DATSIZE_1BYTE);
- for (uint8_t i = 0; i < XMEGA_CRC_LENGTH; i++)
+ for (uint8_t i = 0; i < XMEGA_CRC_LENGTH_BYTES; i++)
((uint8_t*)CRCDest)[i] = XPROGTarget_ReceiveByte();
- return (TimeoutTicksRemaining != 0);
+ return (TimeoutTicksRemaining > 0);
}
/** Reads memory from the target's memory spaces.
while (ReadSize-- && TimeoutTicksRemaining)
*(ReadBuffer++) = XPROGTarget_ReceiveByte();
- return (TimeoutTicksRemaining != 0);
+ return (TimeoutTicksRemaining > 0);
}
/** Writes byte addressed memory to the target's memory spaces.
/* Set CMDEX bit in NVM CTRLA register to start the buffer erase */
XPROGTarget_SendByte(PDI_CMD_STS | (PDI_DATSIZE_4BYTES << 2));
XMEGANVM_SendNVMRegAddress(XMEGA_NVM_REG_CTRLA);
- XPROGTarget_SendByte(1 << 0);
+ XPROGTarget_SendByte(XMEGA_NVM_BIT_CTRLA_CMDEX);
}
if (WriteSize)
/* Set CMDEX bit in NVM CTRLA register to start the erase sequence */
XPROGTarget_SendByte(PDI_CMD_STS | (PDI_DATSIZE_4BYTES << 2));
XMEGANVM_SendNVMRegAddress(XMEGA_NVM_REG_CTRLA);
- XPROGTarget_SendByte(1 << 0);
+ XPROGTarget_SendByte(XMEGA_NVM_BIT_CTRLA_CMDEX);
}
else if (EraseCommand == XMEGA_NVM_CMD_ERASEEEPROM)
{
/* Set CMDEX bit in NVM CTRLA register to start the buffer erase */
XPROGTarget_SendByte(PDI_CMD_STS | (PDI_DATSIZE_4BYTES << 2));
XMEGANVM_SendNVMRegAddress(XMEGA_NVM_REG_CTRLA);
- XPROGTarget_SendByte(1 << 0);
+ XPROGTarget_SendByte(XMEGA_NVM_BIT_CTRLA_CMDEX);
/* Wait until the NVM controller is no longer busy */
if (!(XMEGANVM_WaitWhileNVMControllerBusy()))
/* Set CMDEX bit in NVM CTRLA register to start the EEPROM erase sequence */
XPROGTarget_SendByte(PDI_CMD_STS | (PDI_DATSIZE_4BYTES << 2));
XMEGANVM_SendNVMRegAddress(XMEGA_NVM_REG_CTRLA);
- XPROGTarget_SendByte(1 << 0);
+ XPROGTarget_SendByte(XMEGA_NVM_BIT_CTRLA_CMDEX);
}
else
{
projects / pub / USBasp.git / blobdiff