Enable sorting of the member functions in the Doxygen output, so that functions in...

[pub/USBasp.git] / LUFA / Drivers / Peripheral / AVR8 / TWI_AVR8.h

diff --git a/LUFA/Drivers/Peripheral/AVR8/TWI_AVR8.h b/LUFA/Drivers/Peripheral/AVR8/TWI_AVR8.h
index 17c1e5c..38ad1f3 100644 (file)
--- a/LUFA/Drivers/Peripheral/AVR8/TWI_AVR8.h
+++ b/LUFA/Drivers/Peripheral/AVR8/TWI_AVR8.h
@@ -54,35 +54,35 @@
  *  \code
  *      // Initialize the TWI driver before first use at 200KHz
  *      TWI_Init(TWI_BIT_PRESCALE_1, TWI_BITLENGTH_FROM_FREQ(1, 200000));
- *
+ *      
  *      // Start a write session to device at device address 0xA0, internal address 0xDC with a 10ms timeout
  *      if (TWI_StartTransmission(0xA0 | TWI_ADDRESS_WRITE, 10) == TWI_ERROR_NoError)
  *      {
  *          TWI_SendByte(0xDC);
- *
+ *          
  *          TWI_SendByte(0x01);
  *          TWI_SendByte(0x02);
  *          TWI_SendByte(0x03);
- *
+ *          
  *          // Must stop transmission afterwards to release the bus
  *          TWI_StopTransmission();
  *      }
- *
+ *      
  *      // Start a read session to device at address 0xA0, internal address 0xDC with a 10ms timeout
  *      if (TWI_StartTransmission(0xA0 | TWI_ADDRESS_WRITE, 10) == TWI_ERROR_NoError)
  *      {
  *          TWI_SendByte(0xDC);
  *          TWI_StopTransmission();
- *
+ *          
  *          if (TWI_StartTransmission(0xA0 | TWI_ADDRESS_READ, 10) == TWI_ERROR_NoError)
  *          {
  *              uint8_t Byte1, Byte2, Byte3;
- *
+ *              
  *              // Read three bytes, acknowledge after the third byte is received
  *              TWI_ReceiveByte(&Byte1, false);
  *              TWI_ReceiveByte(&Byte2, false);
  *              TWI_ReceiveByte(&Byte3, true);
- *
+ *              
  *              // Must stop transmission afterwards to release the bus
  *              TWI_StopTransmission();
  *          }
@@ -93,18 +93,18 @@
  *  \code
  *      // Initialize the TWI driver before first use at 200KHz
  *      TWI_Init(TWI_BIT_PRESCALE_1, TWI_BITLENGTH_FROM_FREQ(1, 200000));
- *
+ *      
  *      // Start a write session to device at device address 0xA0, internal address 0xDC with a 10ms timeout
  *      uint8_t InternalWriteAddress = 0xDC;
  *      uint8_t WritePacket[3] = {0x01, 0x02, 0x03};
- *
+ *      
  *      TWI_WritePacket(0xA0, 10, &InternalWriteAddress, sizeof(InternalWriteAddress),
  *                      &WritePacket, sizeof(WritePacket);
- *
+ *      
  *      // Start a read session to device at address 0xA0, internal address 0xDC with a 10ms timeout
  *      uint8_t InternalReadAddress = 0xDC;
  *      uint8_t ReadPacket[3];
- *
+ *      
  *      TWI_ReadPacket(0xA0, 10, &InternalReadAddress, sizeof(InternalReadAddress),
  *                     &ReadPacket, sizeof(ReadPacket);
  *  \endcode
@@ -196,8 +196,8 @@
                         *
                         *  The generated SCL frequency will be according to the formula <pre>F_CPU / (16 + 2 * BitLength + 4 ^ Prescale)</pre>.
                         *
-                        *  \note The value of the \c BitLength parameter should not be set below 10 or invalid bus conditions may
-                        *        occur, as indicated in the AVR8 microcontroller datasheet.
+                        *  \attention The value of the \c BitLength parameter should not be set below 10 or invalid bus conditions may
+                        *             occur, as indicated in the AVR8 microcontroller datasheet.
                         *
                         *  \param[in] Prescale   Prescaler to use when determining the bus frequency, a \c TWI_BIT_PRESCALE_* value.
                         *  \param[in] BitLength  Length of the bits sent on the bus.