# make doxygen = Generate DoxyGen documentation for the project (must have
# DoxyGen installed)
#
-# make debug = Start either simulavr or avarice as specified for debugging,
+# make debug = Start either simulavr or avarice as specified for debugging,
# with avr-gdb or avr-insight as the front end for debugging.
#
# make filename.s = Just compile filename.c into the assembler code only.
MCU = at90usb1287
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+
# Target board (see library "Board Types" documentation, NONE for projects not requiring
-# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
+# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
# "Board" inside the application directory.
BOARD = USBKEY
# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
-# This will be an integer division of F_CLOCK below, as it is sourced by
-# F_CLOCK after it has run through any CPU prescalers. Note that this value
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
# Input clock frequency.
-# This will define a symbol, F_CLOCK, in all source code files equal to the
+# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_CLOCK = $(F_CPU)
+F_USB = $(F_CPU)
# Output format. (can be srec, ihex, binary)
# LUFA library compile-time options and predefined tokens
+LUFA_OPTS += -D DEVICE_STATE_AS_GPIOR=0
+LUFA_OPTS += -D HOST_STATE_AS_GPIOR=1
+LUFA_OPTS += -D ORDERED_EP_CONFIG
LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8
LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1
LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
Lib/PetiteFATFs/pff.c \
$(LUFA_SRC_USB) \
$(LUFA_SRC_USBCLASS) \
- $(LUFA_SRC_SERIAL) \
- $(LUFA_SRC_SERIALSTREAM)
+ $(LUFA_SRC_SERIAL)
# List C++ source files here. (C dependencies are automatically generated.)
-CPPSRC =
+CPPSRC =
# List Assembler source files here.
ASRC =
-# Optimization level, can be [0, 1, 2, 3, s].
+# Optimization level, can be [0, 1, 2, 3, s].
# 0 = turn off optimization. s = optimize for size.
# (Note: 3 is not always the best optimization level. See avr-libc FAQ.)
OPT = s
# Place -D or -U options here for C sources
CDEFS = -DF_CPU=$(F_CPU)UL
-CDEFS += -DF_CLOCK=$(F_CLOCK)UL
-CDEFS += -DBOARD=BOARD_$(BOARD)
+CDEFS += -DF_USB=$(F_USB)UL
+CDEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
CDEFS += $(LUFA_OPTS)
# Place -D or -U options here for ASM sources
ADEFS = -DF_CPU=$(F_CPU)
-ADEFS += -DF_CLOCK=$(F_CLOCK)UL
+ADEFS += -DF_USB=$(F_USB)UL
ADEFS += -DBOARD=BOARD_$(BOARD)
ADEFS += $(LUFA_OPTS)
# Place -D or -U options here for C++ sources
CPPDEFS = -DF_CPU=$(F_CPU)UL
-CPPDEFS += -DF_CLOCK=$(F_CLOCK)UL
+CPPDEFS += -DF_USB=$(F_USB)UL
CPPDEFS += -DBOARD=BOARD_$(BOARD)
CPPDEFS += $(LUFA_OPTS)
#CPPDEFS += -D__STDC_LIMIT_MACROS
# for use in COFF files, additional information about filenames
# and function names needs to be present in the assembler source
# files -- see avr-libc docs [FIXME: not yet described there]
-# -listing-cont-lines: Sets the maximum number of continuation lines of hex
+# -listing-cont-lines: Sets the maximum number of continuation lines of hex
# dump that will be displayed for a given single line of source input.
ASFLAGS = $(ADEFS) -Wa,-adhlns=$(<:%.S=$(OBJDIR)/%.lst),-gstabs,--listing-cont-lines=100
PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt
# If this is left blank, then it will use the Standard printf version.
-PRINTF_LIB =
+PRINTF_LIB =
#PRINTF_LIB = $(PRINTF_LIB_MIN)
#PRINTF_LIB = $(PRINTF_LIB_FLOAT)
SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt
# If this is left blank, then it will use the Standard scanf version.
-SCANF_LIB =
+SCANF_LIB =
#SCANF_LIB = $(SCANF_LIB_MIN)
#SCANF_LIB = $(SCANF_LIB_FLOAT)
# Each directory must be seperated by a space.
# Use forward slashes for directory separators.
# For a directory that has spaces, enclose it in quotes.
-EXTRALIBDIRS =
+EXTRALIBDIRS =
# -Map: create map file
# --cref: add cross reference to map file
LDFLAGS = -Wl,-Map=$(TARGET).map,--cref
-LDFLAGS += -Wl,--relax
+LDFLAGS += -Wl,--relax
LDFLAGS += -Wl,--gc-sections
LDFLAGS += $(EXTMEMOPTS)
LDFLAGS += $(patsubst %,-L%,$(EXTRALIBDIRS))
#AVRDUDE_NO_VERIFY = -V
# Increase verbosity level. Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
# to submit bug reports.
#AVRDUDE_VERBOSE = -v -v
DEBUG_PORT = 4242
# Debugging host used to communicate between GDB / avarice / simulavr, normally
-# just set to localhost unless doing some sort of crazy debugging when
+# just set to localhost unless doing some sort of crazy debugging when
# avarice is running on a different computer.
DEBUG_HOST = localhost
MSG_ERRORS_NONE = Errors: none
MSG_BEGIN = -------- begin --------
MSG_END = -------- end --------
-MSG_SIZE_BEFORE = Size before:
+MSG_SIZE_BEFORE = Size before:
MSG_SIZE_AFTER = Size after:
MSG_COFF = Converting to AVR COFF:
MSG_EXTENDED_COFF = Converting to AVR Extended COFF:
# Define all object files.
-OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
+OBJ = $(SRC:%.c=$(OBJDIR)/%.o) $(CPPSRC:%.cpp=$(OBJDIR)/%.o) $(ASRC:%.S=$(OBJDIR)/%.o)
# Define all listing files.
-LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
+LST = $(SRC:%.c=$(OBJDIR)/%.lst) $(CPPSRC:%.cpp=$(OBJDIR)/%.lst) $(ASRC:%.S=$(OBJDIR)/%.lst)
# Compiler flags to generate dependency files.
# Display compiler version information.
-gccversion :
+gccversion :
@$(CC) --version
-# Program the device.
+# Program the device.
program: $(TARGET).hex $(TARGET).eep
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
# Generate avr-gdb config/init file which does the following:
-# define the reset signal, load the target file, connect to target, and set
+# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
-gdb-config:
+gdb-config:
@$(REMOVE) $(GDBINIT_FILE)
@echo define reset >> $(GDBINIT_FILE)
@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)
$(OBJDIR)/%.o : %.c
@echo
@echo $(MSG_COMPILING) $<
- $(CC) -c $(ALL_CFLAGS) $< -o $@
+ $(CC) -c $(ALL_CFLAGS) $< -o $@
# Compile: create object files from C++ source files.
$(OBJDIR)/%.o : %.cpp
@echo
@echo $(MSG_COMPILING_CPP) $<
- $(CC) -c $(ALL_CPPFLAGS) $< -o $@
+ $(CC) -c $(ALL_CPPFLAGS) $< -o $@
# Compile: create assembler files from C source files.
# Create preprocessed source for use in sending a bug report.
%.i : %.c
- $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
+ $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
# Target: clean project.
clean_doxygen:
rm -rf Documentation
+checksource:
+ @for f in $(SRC) $(CPPSRC) $(ASRC); do \
+ if [ -f $$f ]; then \
+ echo "Found Source File: $$f" ; \
+ else \
+ echo "Source File Not Found: $$f" ; \
+ fi; done
+
+
# Create object files directory
$(shell mkdir $(OBJDIR) 2>/dev/null)
.PHONY : all begin finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff doxygen clean \
clean_list clean_doxygen program dfu flip flip-ee dfu-ee \
-debug gdb-config
+debug gdb-config checksource
projects / pub / USBasp.git / blobdiff