Fix error in AVRISP programmer when repeatedly using PDI mode via the hardware USART...

[pub/USBasp.git] / Projects / Magstripe / Magstripe.txt

diff --git a/Projects/Magstripe/Magstripe.txt b/Projects/Magstripe/Magstripe.txt
index a0e600e..1958627 100644 (file)
--- a/Projects/Magstripe/Magstripe.txt
+++ b/Projects/Magstripe/Magstripe.txt
@@ -6,6 +6,13 @@
  \r
 /** \mainpage Denver Gingerich's USBSnoop Magnetic Card Reader Project\r
  *\r
+ *  \section SSec_Compat Demo Compatibility:\r
+ *\r
+ *  The following list indicates what microcontrollers are compatible with this demo.\r
+ *\r
+ *  - AT90USB1287\r
+ *  - AT90USB1286\r
+ *\r
  *  \section SSec_Info USB Information:\r
  *\r
  *  The following table gives a rundown of the USB utilization of this demo.\r
@@ -29,7 +36,7 @@
  *  </tr>\r
  *  <tr>\r
  *   <td><b>Usable Speeds:</b></td>\r
- *   <td>Low Speed Mode, Full Speed Mode</td>\r
+ *   <td>Full Speed Mode</td>\r
  *  </tr>\r
  * </table>\r
  *\r
@@ -37,9 +44,9 @@
  *\r
  *  Firmware for a USB AVR powered USB TTL magnetic stripe reader (using a card\r
  *  reader such as the Omron V3B-4K) by Denver Gingerich. This project is designed\r
- *  to be used with the open source Stripe Snoop project at http://stripesnoop.sourceforge.net/.\r
+ *  to be used with the open source Stripe Snoop project at <a>http://stripesnoop.sourceforge.net/</a>.\r
  * \r
- *  See http://ossguy.com/ss_usb/ for the USB reader hardware project website,\r
+ *  See <a>http://ossguy.com/ss_usb/</a> for the USB reader hardware project website,\r
  *  including construction and support details.\r
  * \r
  *  To use, connect your magnetic card reader device to the USB AVR as follows (pin and port mapping may be adjusted\r
@@ -103,5 +110,55 @@
  *    <td>CircularBitBuffer.h</td>\r
  *    <td>Gives the maximum number of bits per track which can be buffered by the device for later transmission to a host.</td>\r
  *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_T1_CLOCK</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's CLOCK line for the reader's track 1 output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_T1_DATA</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's DATA line for the reader's track 1 output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_T2_CLOCK</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's CLOCK line for the reader's track 2 output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_T2_DATA</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's DATA line for the reader's track 2 output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_T3_CLOCK</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's CLOCK line for the reader's track 3 output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_T3_DATA</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's DATA line for the reader's track 3 output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_CARDPRESENT</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>Mask for the magnetic card reader's card detection output.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_PIN</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>PIN register that the magnetic card reader device is attached to.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_PORT</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>PORT register that the magnetic card reader device is attached to.</td>\r
+ *   </tr>\r
+ *   <tr>\r
+ *    <td>MAG_DDR</td>\r
+ *    <td>Makefile CDEFS</td>\r
+ *    <td>DDR register that the magnetic card reader device is attached to.</td>\r
+ *   </tr>\r
  *  </table>\r
  */\r