Update Studio Integration DLL, to include package logging.

[pub/USBasp.git] / Projects / AVRISP-MKII / AVRISP-MKII.c

diff --git a/Projects/AVRISP-MKII/AVRISP-MKII.c b/Projects/AVRISP-MKII/AVRISP-MKII.c
index 71b6da7..6d4bc89 100644 (file)
--- a/Projects/AVRISP-MKII/AVRISP-MKII.c
+++ b/Projects/AVRISP-MKII/AVRISP-MKII.c
@@ -1,13 +1,13 @@
 /*
              LUFA Library
-     Copyright (C) Dean Camera, 2012.
+     Copyright (C) Dean Camera, 2015.
 
   dean [at] fourwalledcubicle [dot] com
            www.lufa-lib.org
 */
 
 /*
-  Copyright 2012  Dean Camera (dean [at] fourwalledcubicle [dot] com)
+  Copyright 2015  Dean Camera (dean [at] fourwalledcubicle [dot] com)
 
   Permission to use, copy, modify, distribute, and sell this
   software and its documentation for any purpose is hereby granted
@@ -18,7 +18,7 @@
   advertising or publicity pertaining to distribution of the
   software without specific, written prior permission.
 
-  The author disclaim all warranties with regard to this
+  The author disclaims all warranties with regard to this
   software, including all implied warranties of merchantability
   and fitness.  In no event shall the author be liable for any
   special, indirect or consequential damages or any damages
@@ -36,6 +36,16 @@
 
 #include "AVRISP-MKII.h"
 
+#if (BOARD != BOARD_NONE)
+  /* Some board hardware definitions (e.g. the Arduino Micro) have their LEDs defined on the same pins
+     as the ISP, PDI or TPI interfaces (see the accompanying project documentation). If a board other
+     than NONE is selected (to enable the LED driver with the programmer) you should double-check that
+     no conflicts will occur. If there is a conflict, turn off the LEDs (set BOARD to NONE in the makefile)
+     or define a custom board driver (see the LUFA manual) with alternative LED mappings.
+  */
+  #warning Board specific drivers have been selected; make sure the board LED driver does not conflict with the programmer ISP/PDI/TPI interfaces.
+#endif
+
 /** Main program entry point. This routine contains the overall program flow, including initial
  *  setup of all components and the main program loop.
  */
@@ -45,7 +55,7 @@ int main(void)
        V2Protocol_Init();
 
        LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
-       sei();
+       GlobalInterruptEnable();
 
        for (;;)
        {
@@ -63,12 +73,14 @@ int main(void)
 /** Configures the board hardware and chip peripherals for the demo's functionality. */
 void SetupHardware(void)
 {
+#if (ARCH == ARCH_AVR8)
        /* Disable watchdog if enabled by bootloader/fuses */
        MCUSR &= ~(1 << WDRF);
        wdt_disable();
 
        /* Disable clock division */
        clock_prescale_set(clock_div_1);
+#endif
 
        /* Hardware Initialization */
        LEDs_Init();
@@ -97,12 +109,12 @@ void EVENT_USB_Device_ConfigurationChanged(void)
 {
        bool ConfigSuccess = true;
 
-       /* Setup AVRISP Data Endpoint(s) */
+       /* Setup AVRISP Data OUT endpoint */
        ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_OUT_EPADDR, EP_TYPE_BULK, AVRISP_DATA_EPSIZE, 1);
 
-       #if defined(LIBUSB_DRIVER_COMPAT)
-       ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_IN_EPADDR, EP_TYPE_BULK, AVRISP_DATA_EPSIZE, 1);
-       #endif
+       /* Setup AVRISP Data IN endpoint if it is using a physically different endpoint */
+       if ((AVRISP_DATA_IN_EPADDR & ENDPOINT_EPNUM_MASK) != (AVRISP_DATA_OUT_EPADDR & ENDPOINT_EPNUM_MASK))
+         ConfigSuccess &= Endpoint_ConfigureEndpoint(AVRISP_DATA_IN_EPADDR, EP_TYPE_BULK, AVRISP_DATA_EPSIZE, 1);
 
        /* Indicate endpoint configuration success or failure */
        LEDs_SetAllLEDs(ConfigSuccess ? LEDMASK_USB_READY : LEDMASK_USB_ERROR);