-/** \file\r
- *\r
- * This file contains special DoxyGen information for the generation of the main page and other special\r
- * documentation pages. It is not a project source file.\r
- */\r
- \r
-/** \mainpage Benito Arduino Programmer Project\r
- *\r
- * \section SSec_Compat Project Compatibility:\r
- *\r
- * The following list indicates what microcontrollers are compatible with this project.\r
- *\r
- * - Series 7 USB AVRs\r
- * - Series 6 USB AVRs\r
- * - Series 4 USB AVRs\r
- * - Series 2 USB AVRs\r
- *\r
- * \section SSec_Info USB Information:\r
- *\r
- * The following table gives a rundown of the USB utilization of this project.\r
- *\r
- * <table>\r
- * <tr>\r
- * <td><b>USB Mode:</b></td>\r
- * <td>Device</td>\r
- * </tr>\r
- * <tr>\r
- * <td><b>USB Class:</b></td>\r
- * <td>Communications Device Class (CDC)</td>\r
- * </tr>\r
- * <tr> \r
- * <td><b>USB Subclass:</b></td>\r
- * <td>Abstract Control Model (ACM)</td>\r
- * </tr>\r
- * <tr>\r
- * <td><b>Relevant Standards:</b></td>\r
- * <td>USBIF CDC Class Standard</td>\r
- * <td>Arduino Bootloader Specification</td>\r
- * </tr>\r
- * <tr>\r
- * <td><b>Usable Speeds:</b></td>\r
- * <td>Full Speed Mode</td>\r
- * </tr>\r
- * </table>\r
- *\r
- * \section SSec_Description Project Description: \r
- *\r
- * Firmware for a USB AVR powered programmer for Arduino boards using the official Arduino bootloader. This\r
- * project acts like a regular USB to Serial bridge, except that asserting the DTR line will cause a pulse\r
- * to appear on a given port pin, to control the target's /RESET pin.\r
- *\r
- * This is primarily designed to fit the Benito board from www.dorkbotpdx.org, but will suit all USB AVRs.\r
- *\r
- * After running this project for the first time on a new computer, you will need to supply the .INF file located\r
- * in this project's directory as the device's driver when running under Windows. This will enable Windows to use\r
- * its inbuilt CDC drivers, negating the need for custom drivers for the device. Other Operating Systems should\r
- * automatically use their own inbuilt CDC-ACM drivers.\r
- *\r
- * \section SSec_Options Project Options\r
- *\r
- * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.\r
- *\r
- * <table>\r
- * <tr>\r
- * <td><b>Define Name:</b></td>\r
- * <td><b>Location:</b></td>\r
- * <td><b>Description:</b></td>\r
- * </tr>\r
- * <tr>\r
- * <td>AVR_RESET_LINE_PORT</td>\r
- * <td>Makefile CDEFS</td>\r
- * <td>Indicates the PORT register of the pin used to generate the target /RESET line pulse.</td>\r
- * </tr>\r
- * <tr>\r
- * <td>AVR_RESET_LINE_DDR</td>\r
- * <td>Makefile CDEFS</td>\r
- * <td>Indicates the DDR register of the pin used to generate the target /RESET line pulse.</td>\r
- * </tr>\r
- * <tr>\r
- * <td>AVR_RESET_LINE_MASK</td>\r
- * <td>Makefile CDEFS</td>\r
- * <td>Indicates the mask of the pin used to generate the target /RESET line pulse.</td>\r
- * </tr>\r
- * <tr>\r
- * <td>AVR_RESET_PULSE_MS</td>\r
- * <td>Makefile CDEFS</td>\r
- * <td>Pulse length in milliseconds for the target /RESET pulse.</td>\r
- * </tr>\r
- * <tr>\r
- * <td>TX_RX_LED_PULSE_MS</td>\r
- * <td>Makefile CDEFS</td>\r
- * <td>Pulse length in milliseconds for the activity Tx/Rx LEDs.</td>\r
- * </tr>\r
- * <tr>\r
- * <td>PING_PONG_LED_PULSE_MS</td>\r
- * <td>Makefile CDEFS</td>\r
- * <td>Pulse length in milliseconds for the enumeration LED ping-poning between toggles.</td>\r
- * </tr>\r
- * </table>\r
- */\r
+/** \file
+ *
+ * This file contains special DoxyGen information for the generation of the main page and other special
+ * documentation pages. It is not a project source file.
+ */
+
+/** \mainpage Benito Arduino Programmer Project
+ *
+ * \section Sec_Compat Project Compatibility:
+ *
+ * The following list indicates what microcontrollers are compatible with this project.
+ *
+ * - Series 7 USB AVRs (AT90USBxxx7)
+ * - Series 6 USB AVRs (AT90USBxxx6)
+ * - Series 4 USB AVRs (ATMEGAxxU4)
+ * - Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2)
+ *
+ * \section Sec_Info USB Information:
+ *
+ * The following table gives a rundown of the USB utilization of this project.
+ *
+ * <table>
+ * <tr>
+ * <td><b>USB Mode:</b></td>
+ * <td>Device</td>
+ * </tr>
+ * <tr>
+ * <td><b>USB Class:</b></td>
+ * <td>Communications Device Class (CDC)</td>
+ * </tr>
+ * <tr>
+ * <td><b>USB Subclass:</b></td>
+ * <td>Abstract Control Model (ACM)</td>
+ * </tr>
+ * <tr>
+ * <td><b>Relevant Standards:</b></td>
+ * <td>USBIF CDC Class Standard \n
+ * Arduino Bootloader Specification</td>
+ * </tr>
+ * <tr>
+ * <td><b>Usable Speeds:</b></td>
+ * <td>Full Speed Mode</td>
+ * </tr>
+ * </table>
+ *
+ * \section Sec_Description Project Description:
+ *
+ * Firmware for a USB AVR powered programmer for Arduino boards using the official Arduino bootloader. This
+ * project acts like a regular USB to Serial bridge, except that asserting the DTR line will cause a pulse
+ * to appear on a given port pin, to control the target's /RESET pin.
+ *
+ * This is primarily designed to fit the Benito board from www.dorkbotpdx.org, but will suit all USB AVRs.
+ *
+ * After running this project for the first time on a new computer, you will need to supply the .INF file located
+ * in this project's directory as the device's driver when running under Windows. This will enable Windows to use
+ * its inbuilt CDC drivers, negating the need for custom drivers for the device. Other Operating Systems should
+ * automatically use their own inbuilt CDC-ACM drivers.
+ *
+ * \section Sec_Options Project Options
+ *
+ * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
+ *
+ * <table>
+ * <tr>
+ * <td><b>Define Name:</b></td>
+ * <td><b>Location:</b></td>
+ * <td><b>Description:</b></td>
+ * </tr>
+ * <tr>
+ * <td>AVR_RESET_LINE_PORT</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Indicates the PORT register of the pin used to generate the target /RESET line pulse.</td>
+ * </tr>
+ * <tr>
+ * <td>AVR_RESET_LINE_DDR</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Indicates the DDR register of the pin used to generate the target /RESET line pulse.</td>
+ * </tr>
+ * <tr>
+ * <td>AVR_RESET_LINE_MASK</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Indicates the mask of the pin used to generate the target /RESET line pulse.</td>
+ * </tr>
+ * <tr>
+ * <td>AVR_RESET_PULSE_MS</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Pulse length in milliseconds for the target /RESET pulse.</td>
+ * </tr>
+ * <tr>
+ * <td>TX_RX_LED_PULSE_MS</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Pulse length in milliseconds for the activity Tx/Rx LEDs.</td>
+ * </tr>
+ * <tr>
+ * <td>PING_PONG_LED_PULSE_MS</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Pulse length in milliseconds for the enumeration LED ping-ponging between toggles.</td>
+ * </tr>
+ * <tr>
+ * <td>RECEIVE_BUFFER_FLUSH_MS</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Period between flushings of received data buffer to the attached USB host.</td>
+ * </tr>
+ * </table>
+ */
+
projects / pub / USBasp.git / blobdiff