Mark build test makefiles as being incompatible with parallel make builds, as they...

[pub/USBasp.git] / LUFA / Drivers / Board / LEDs.h

diff --git a/LUFA/Drivers/Board/LEDs.h b/LUFA/Drivers/Board/LEDs.h
index 0c7324f..21f89aa 100644 (file)
--- a/LUFA/Drivers/Board/LEDs.h
+++ b/LUFA/Drivers/Board/LEDs.h
@@ -63,7 +63,7 @@
  *
  *  \note To make code as compatible as possible, it is assumed that all boards carry a minimum of four LEDs. If
  *        a board contains less than four LEDs, the remaining LED masks are defined to 0 so as to have no effect.
- *        If other behaviour is desired, either alias the remaining LED masks to existing LED masks via the -D
+ *        If other behavior is desired, either alias the remaining LED masks to existing LED masks via the -D
  *        switch in the project makefile, or alias them to nothing in the makefile to cause compilation errors when
  *        a non-existing LED is referenced in application code. Note that this means that it is possible to make
  *        compatible code for a board with no LEDs by making a board LED driver (see \ref Page_WritingBoardDrivers)
@@ -76,21 +76,21 @@
  *  \code
  *      // Initialize the board LED driver before first use
  *      LEDs_Init();
- *
+ *      
  *      // Turn on each of the four LEDs in turn
  *      LEDs_SetAllLEDs(LEDS_LED1);
  *      Delay_MS(500);
- *      LEDs_SetAllLEDs(LEDS_LED1);
+ *      LEDs_SetAllLEDs(LEDS_LED2);
  *      Delay_MS(500);
- *      LEDs_SetAllLEDs(LEDS_LED1);
+ *      LEDs_SetAllLEDs(LEDS_LED3);
  *      Delay_MS(500);
- *      LEDs_SetAllLEDs(LEDS_LED1);
+ *      LEDs_SetAllLEDs(LEDS_LED4);
  *      Delay_MS(500);
- *
+ *      
  *      // Turn on all LEDs
  *      LEDs_SetAllLEDs(LEDS_ALL_LEDS);
  *      Delay_MS(1000);
- *
+ *      
  *      // Turn on LED 1, turn off LED 2, leaving LEDs 3 and 4 in their current state
  *      LEDs_ChangeLEDs((LEDS_LED1 | LEDS_LED2), LEDS_LED1);
  *  \endcode
@@ -109,6 +109,7 @@
 
                #if (BOARD == BOARD_NONE)
                        static inline void LEDs_Init(void) {};
+                       static inline void LEDs_Disable(void) {};
                        static inline void LEDs_TurnOnLEDs(const uint_reg_t LEDMask) {};
                        static inline void LEDs_TurnOffLEDs(const uint_reg_t LEDMask) {};
                        static inline void LEDs_SetAllLEDs(const uint_reg_t LEDMask) {};
@@ -180,6 +181,16 @@
                        #include "AVR8/MICROPENDOUS/LEDs.h"
                #elif (BOARD == BOARD_B1_XPLAINED)
                        #include "XMEGA/B1_XPLAINED/LEDs.h"
+               #elif (BOARD == BOARD_MULTIO)
+                       #include "AVR8/MULTIO/LEDs.h"
+               #elif (BOARD == BOARD_BIGMULTIO)
+                       #include "AVR8/BIGMULTIO/LEDs.h"
+               #elif (BOARD == BOARD_DUCE)
+                       #include "AVR8/DUCE/LEDs.h"
+               #elif (BOARD == BOARD_OLIMEX32U4)
+                       #include "AVR8/OLIMEX32U4/LEDs.h"               
+               #elif (BOARD == BOARD_OLIMEXT32U4)
+                       #include "AVR8/OLIMEXT32U4/LEDs.h"              
                #else
                        #include "Board/LEDs.h"
                #endif
@@ -210,7 +221,7 @@
                 */
                static inline void LEDs_Init(void);
 
-               /** Disables the board LED driver, releasing the I/O pins back to their default high-impedence input mode. */
+               /** Disables the board LED driver, releasing the I/O pins back to their default high-impedance input mode. */
                static inline void LEDs_Disable(void);
 
                /** Turns on the LEDs specified in the given LED mask.