Implemented on-demand PLL clock generation for the U4, U6 and U7 series USB AVRs...

[pub/USBasp.git] / Bootloaders / CDC / BootloaderCDC.c

diff --git a/Bootloaders/CDC/BootloaderCDC.c b/Bootloaders/CDC/BootloaderCDC.c
index 0f7b266..99e0ccb 100644 (file)
--- a/Bootloaders/CDC/BootloaderCDC.c
+++ b/Bootloaders/CDC/BootloaderCDC.c
@@ -39,22 +39,22 @@
 /** Contains the current baud rate and other settings of the first virtual serial port. This must be retained as some
  *  operating systems will not open the port unless the settings can be set successfully.
  */
-CDC_Line_Coding_t LineEncoding = { .BaudRateBPS = 0,
-                                   .CharFormat  = OneStopBit,
-                                   .ParityType  = Parity_None,
-                                   .DataBits    = 8            };
+static CDC_LineEncoding_t LineEncoding = { .BaudRateBPS = 0,
+                                           .CharFormat  = CDC_LINEENCODING_OneStopBit,
+                                           .ParityType  = CDC_PARITY_None,
+                                           .DataBits    = 8                            };
 
 /** Current address counter. This stores the current address of the FLASH or EEPROM as set by the host,
  *  and is used when reading or writing to the AVRs memory (either FLASH or EEPROM depending on the issued
  *  command.)
  */
-uint32_t CurrAddress;
+static uint32_t CurrAddress;
 
 /** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
  *  via a watchdog reset. When cleared the bootloader will exit, starting the watchdog and entering an infinite
  *  loop until the AVR restarts and the application runs.
  */
-bool RunBootloader = true;
+static bool RunBootloader = true;
 
 
 /** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
@@ -127,27 +127,34 @@ void EVENT_USB_Device_ConfigurationChanged(void)
  */
 void EVENT_USB_Device_ControlRequest(void)
 {
+       /* Ignore any requests that aren't directed to the CDC interface */
+       if ((USB_ControlRequest.bmRequestType & (CONTROL_REQTYPE_TYPE | CONTROL_REQTYPE_RECIPIENT)) !=
+           (REQTYPE_CLASS | REQREC_INTERFACE))
+       {
+               return;
+       }
+
        /* Process CDC specific control requests */
        switch (USB_ControlRequest.bRequest)
        {
-               case REQ_GetLineEncoding:
+               case CDC_REQ_GetLineEncoding:
                        if (USB_ControlRequest.bmRequestType == (REQDIR_DEVICETOHOST | REQTYPE_CLASS | REQREC_INTERFACE))
                        {
                                Endpoint_ClearSETUP();
 
                                /* Write the line coding data to the control endpoint */
-                               Endpoint_Write_Control_Stream_LE(&LineEncoding, sizeof(CDC_Line_Coding_t));
+                               Endpoint_Write_Control_Stream_LE(&LineEncoding, sizeof(CDC_LineEncoding_t));
                                Endpoint_ClearOUT();
                        }
 
                        break;
-               case REQ_SetLineEncoding:
+               case CDC_REQ_SetLineEncoding:
                        if (USB_ControlRequest.bmRequestType == (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE))
                        {
                                Endpoint_ClearSETUP();
 
                                /* Read the line coding data in from the host into the global struct */
-                               Endpoint_Read_Control_Stream_LE(&LineEncoding, sizeof(CDC_Line_Coding_t));
+                               Endpoint_Read_Control_Stream_LE(&LineEncoding, sizeof(CDC_LineEncoding_t));
                                Endpoint_ClearIN();
                        }