* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
-
+
/** \mainpage AVRISP MKII Programmer Project
*
- * \section SSec_Compat Project Compatibility:
+ * \section Sec_Compat Project Compatibility:
*
* The following list indicates what microcontrollers are compatible with this project.
*
- * - Series 7 USB AVRs
- * - Series 6 USB AVRs
- * - Series 4 USB AVRs
- * - Series 2 USB AVRs (8KB versions with reduced features only)
+ * - Series 7 USB AVRs (AT90USBxxx7)
+ * - Series 6 USB AVRs (AT90USBxxx6)
+ * - Series 4 USB AVRs (ATMEGAxxU4)
+ * - Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - <i>8KB versions with reduced features only</i>
*
- * \section SSec_Info USB Information:
+ * \section Sec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this project.
*
* <td><b>USB Class:</b></td>
* <td>Vendor Specific Class</td>
* </tr>
- * <tr>
+ * <tr>
* <td><b>USB Subclass:</b></td>
* <td>N/A</td>
* </tr>
* </tr>
* </table>
*
- * \section SSec_Description Project Description:
+ * \section Sec_Description Project Description:
*
* Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
* microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
* </tr>
* </table>
*
- * In addition, the AVR's XCK pin will generate a .5MHz clock when SPI programming is used, to act as an external
- * device clock if the fuses have been mis-set. To use the recovery clock, connect XCK to the target AVR's XTAL1
- * pin, and set the ISP programming speed to 125KHz or below.
+ * In addition, the AVR's OCR1A pin will generate a 4MHz clock, to act as an external rescue device clock if the
+ * fuses have been mis-set. To use the recovery clock, connect the OCR1A pin of the USB AVR to the target AVR's
+ * XTAL1 pin, and set the ISP programming speed to 125KHz (note: other ISP speeds will not work correctly).
*
- * <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
- * <b><sup>2</sup></b> <i>See AUX line related tokens in the \ref SSec_Options section</i>
+ * <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n
+ * <b><sup>2</sup></b> <i>See AUX line related tokens in the \ref Sec_Options section</i>
*
* \section Sec_PDI PDI Connections
* Connections to the device for PDI programming (when enabled):
* </tr>
* </table>
*
- * <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
+ * <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n
* <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n
*
* \section Sec_TPI TPI Connections
* </tr>
* </table>
*
- * <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
+ * <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n
* <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n
- * <b><sup>3</sup></b> <i>See AUX line related tokens in the \ref SSec_Options section</i>
+ * <b><sup>3</sup></b> <i>See AUX line related tokens in the \ref Sec_Options section</i>
*
- * \section SSec_Options Project Options
+ * \section Sec_Options Project Options
*
* The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
*
* <td>VTARGET_ADC_CHANNEL</td>
* <td>Makefile LUFA_OPTS</td>
* <td>ADC channel number (on supported AVRs) to use for VTARGET level detection, if NO_VTARGET_DETECT is not defined.
- * <i>Ignored when compiled for targets lacking an ADC.</i></td>
+ * <i>Ignored when compiled for targets lacking an ADC.</i></td>
* </tr>
* <tr>
* <td>ENABLE_ISP_PROTOCOL</td>
* <td>Makefile LUFA_OPTS</td>
- * <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * <td>Define to enable SPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>ENABLE_XPROG_PROTOCOL</td>
* <td>Makefile LUFA_OPTS</td>
- * <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
+ * <td>Define to enable PDI and TPI programming protocol support. <i>Ignored when compiled for the XPLAIN board.</i></td>
* </tr>
* <tr>
* <td>NO_VTARGET_DETECT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to disable VTARGET sampling and reporting on AVR models with an ADC converter. This will cause the programmer
* to report a fixed 5V target voltage to the host regardless of the real target voltage. <i>Ignored when compiled for
- * targets lacking an ADC.</i></td>
+ * targets lacking an ADC.</i></td>
* </tr>
* <tr>
* <td>VTARGET_REF_VOLTS</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Indicates the programmer AVR's AVCC reference voltage when measuring the target's supply voltage. Note that the supply
* voltage should never exceed the reference voltage on the programmer AVR without some form of protection to prevent damage
- * to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
+ * to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
* </tr>
* <tr>
* <td>VTARGET_SCALE_FACTOR</td>
* <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the
* ADC pin for measuring the target's supply voltage, so that voltages above the programmer AVR's AVCC reference voltage can be
* measured. This should be the reciprocal of the division performed - e.g. if the VTARGET voltage is halved, this should be set
- * to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
- * </tr>
+ * to 2. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
+ * </tr>
* <tr>
* <td>LIBUSB_DRIVER_COMPAT</td>
* <td>Makefile LUFA_OPTS</td>
* <td>Define to switch to a non-standard endpoint scheme, breaking compatibility with AVRStudio under Windows but making
* the code compatible with software such as avrdude (all platforms) that use the libUSB driver.
* </tr>
+ * <tr>
+ * <td>XCK_RESCUE_CLOCK_ENABLE</td>
+ * <td>Makefile LUFA_OPTS</td>
+ * <td>Define to move the ISP rescue clock to the AVR's XCK pin instead of the OCR1A output pin. This is useful for existing programming
+ * hardware that does not expose the OCR1A pin of the AVR, but *may* cause some issues with PDI programming mode.
+ * </tr>
* </table>
*/
+
projects / pub / USBasp.git / blobdiff