Removed all user pipe/endpoint interrupt APIs, added internal library support for...

[pub/USBasp.git] / Demos / Device / GenericHID / GenericHID.c

diff --git a/Demos/Device/GenericHID/GenericHID.c b/Demos/Device/GenericHID/GenericHID.c
index d4e7cca..0369f9f 100644 (file)
--- a/Demos/Device/GenericHID/GenericHID.c
+++ b/Demos/Device/GenericHID/GenericHID.c
@@ -39,10 +39,7 @@
 /* Scheduler Task List */\r
 TASK_LIST\r
 {\r
-       #if !defined(INTERRUPT_CONTROL_ENDPOINT)\r
        { .Task = USB_USBTask          , .TaskStatus = TASK_STOP },\r
-       #endif\r
-       \r
        { .Task = USB_HID_Report       , .TaskStatus = TASK_STOP },\r
 };\r
 \r
@@ -75,30 +72,13 @@ int main(void)
        Scheduler_Start();\r
 }\r
 \r
-/** Event handler for the USB_Reset event. This fires when the USB interface is reset by the USB host, before the\r
- *  enumeration process begins, and enables the control endpoint interrupt so that control requests can be handled\r
- *  asynchronously when they arrive rather than when the control endpoint is polled manually.\r
- */\r
-EVENT_HANDLER(USB_Reset)\r
-{\r
-       #if defined(INTERRUPT_CONTROL_ENDPOINT)\r
-       /* Select the control endpoint */\r
-       Endpoint_SelectEndpoint(ENDPOINT_CONTROLEP);\r
-\r
-       /* Enable the endpoint SETUP interrupt ISR for the control endpoint */\r
-       USB_INT_Enable(ENDPOINT_INT_SETUP);\r
-       #endif\r
-}\r
-\r
 /** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and\r
  *  starts the library USB task to begin the enumeration and USB management process.\r
  */\r
 EVENT_HANDLER(USB_Connect)\r
 {\r
-       #if !defined(INTERRUPT_CONTROL_ENDPOINT)\r
        /* Start USB management task */\r
        Scheduler_SetTaskMode(USB_USBTask, TASK_RUN);\r
-       #endif\r
 \r
        /* Indicate USB enumerating */\r
        UpdateStatus(Status_USBEnumerating);\r
@@ -111,10 +91,7 @@ EVENT_HANDLER(USB_Disconnect)
 {\r
        /* Stop running HID reporting and USB management tasks */\r
        Scheduler_SetTaskMode(USB_HID_Report, TASK_STOP);\r
-\r
-       #if !defined(INTERRUPT_CONTROL_ENDPOINT)\r
        Scheduler_SetTaskMode(USB_USBTask, TASK_STOP);\r
-       #endif\r
 \r
        /* Indicate USB not ready */\r
        UpdateStatus(Status_USBNotReady);\r
@@ -298,32 +275,3 @@ TASK(USB_HID_Report)
                }\r
        }\r
 }\r
-\r
-#if defined(INTERRUPT_CONTROL_ENDPOINT)\r
-/** ISR for the general Pipe/Endpoint interrupt vector. This ISR fires when an endpoint's status changes (such as\r
- *  a packet has been received) on an endpoint with its corresponding ISR enabling bits set. This is used to send\r
- *  HID packets to the host each time the HID interrupt endpoints polling period elapses, as managed by the USB\r
- *  controller.\r
- */\r
-ISR(ENDPOINT_PIPE_vect, ISR_BLOCK)\r
-{\r
-       /* Save previously selected endpoint before selecting a new endpoint */\r
-       uint8_t PrevSelectedEndpoint = Endpoint_GetCurrentEndpoint();\r
-\r
-       /* Check if the control endpoint has received a request */\r
-       if (Endpoint_HasEndpointInterrupted(ENDPOINT_CONTROLEP))\r
-       {\r
-               /* Clear the endpoint interrupt */\r
-               Endpoint_ClearEndpointInterrupt(ENDPOINT_CONTROLEP);\r
-\r
-               /* Process the control request */\r
-               USB_USBTask();\r
-\r
-               /* Handshake the endpoint setup interrupt - must be after the call to USB_USBTask() */\r
-               USB_INT_Clear(ENDPOINT_INT_SETUP);\r
-       }\r
-\r
-       /* Restore previously selected endpoint */\r
-       Endpoint_SelectEndpoint(PrevSelectedEndpoint);\r
-}\r
-#endif\r