/*
LUFA Library
- Copyright (C) Dean Camera, 2011.
+ Copyright (C) Dean Camera, 2015.
dean [at] fourwalledcubicle [dot] com
www.lufa-lib.org
*/
/*
- Copyright 2011 Dean Camera (dean [at] fourwalledcubicle [dot] com)
+ Copyright 2015 Dean Camera (dean [at] fourwalledcubicle [dot] com)
- Permission to use, copy, modify, distribute, and sell this
+ Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby granted
- without fee, provided that the above copyright notice appear in
+ without fee, provided that the above copyright notice appear in
all copies and that both that the copyright notice and this
- permission notice and warranty disclaimer appear in supporting
- documentation, and that the name of the author not be used in
- advertising or publicity pertaining to distribution of the
+ permission notice and warranty disclaimer appear in supporting
+ documentation, and that the name of the author not be used in
+ advertising or publicity pertaining to distribution of the
software without specific, written prior permission.
- The author disclaim all warranties with regard to this
+ The author disclaims all warranties with regard to this
software, including all implied warranties of merchantability
and fitness. In no event shall the author be liable for any
special, indirect or consequential damages or any damages
*
* Main source file for the HID class bootloader. This file contains the complete bootloader logic.
*/
-
+
#include "BootloaderHID.h"
/** Flag to indicate if the bootloader should be running, or should exit and allow the application code to run
*/
static bool RunBootloader = true;
-/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
+/** Magic lock for forced application start. If the HWBE fuse is programmed and BOOTRST is unprogrammed, the bootloader
+ * will start if the /HWB line of the AVR is held low and the system is reset. However, if the /HWB line is still held
+ * low when the application attempts to start via a watchdog reset, the bootloader will re-start. If set to the value
+ * \ref MAGIC_BOOT_KEY the special init function \ref Application_Jump_Check() will force the application to start.
+ */
+uint16_t MagicBootKey ATTR_NO_INIT;
+
+
+/** Special startup routine to check if the bootloader was started via a watchdog reset, and if the magic application
+ * start key has been loaded into \ref MagicBootKey. If the bootloader started via the watchdog and the key is valid,
+ * this will force the user application to start via a software jump.
+ */
+void Application_Jump_Check(void)
+{
+ /* If the reset source was the bootloader and the key is correct, clear it and jump to the application */
+ if ((MCUSR & (1 << WDRF)) && (MagicBootKey == MAGIC_BOOT_KEY))
+ {
+ MagicBootKey = 0;
+
+ // cppcheck-suppress constStatement
+ ((void (*)(void))0x0000)();
+ }
+}
+
+/** Main program entry point. This routine configures the hardware required by the bootloader, then continuously
* runs the bootloader processing routine until instructed to soft-exit.
*/
int main(void)
{
/* Setup hardware required for the bootloader */
SetupHardware();
-
+
/* Enable global interrupts so that the USB stack can function */
- sei();
+ GlobalInterruptEnable();
while (RunBootloader)
USB_USBTask();
-
+
/* Disconnect from the host - USB interface will be reset later along with the AVR */
USB_Detach();
+ /* Unlock the forced application start mode of the bootloader if it is restarted */
+ MagicBootKey = MAGIC_BOOT_KEY;
+
/* Enable the watchdog and force a timeout to reset the AVR */
wdt_enable(WDTO_250MS);
}
/** Configures all hardware required for the bootloader. */
-void SetupHardware(void)
+static void SetupHardware(void)
{
/* Disable watchdog if enabled by bootloader/fuses */
MCUSR &= ~(1 << WDRF);
void EVENT_USB_Device_ConfigurationChanged(void)
{
/* Setup HID Report Endpoint */
- Endpoint_ConfigureEndpoint(HID_IN_EPNUM, EP_TYPE_INTERRUPT,
- ENDPOINT_DIR_IN, HID_IN_EPSIZE,
- ENDPOINT_BANK_SINGLE);
+ Endpoint_ConfigureEndpoint(HID_IN_EPADDR, EP_TYPE_INTERRUPT, HID_IN_EPSIZE, 1);
}
/** Event handler for the USB_ControlRequest event. This is used to catch and process control requests sent to
{
case HID_REQ_SetReport:
Endpoint_ClearSETUP();
-
+
/* Wait until the command has been sent by the host */
while (!(Endpoint_IsOUTReceived()));
-
+
/* Read in the write destination address */
#if (FLASHEND > 0xFFFF)
uint32_t PageAddress = ((uint32_t)Endpoint_Read_16_LE() << 8);
#else
uint16_t PageAddress = Endpoint_Read_16_LE();
#endif
-
+
/* Check if the command is a program page command, or a start application command */
#if (FLASHEND > 0xFFFF)
if ((uint16_t)(PageAddress >> 8) == COMMAND_STARTAPPLICATION)
/* Erase the given FLASH page, ready to be programmed */
boot_page_erase(PageAddress);
boot_spm_busy_wait();
-
+
/* Write each of the FLASH page's bytes in sequence */
- for (uint8_t PageWord = 0; PageWord < (SPM_PAGESIZE / 2); PageWord++)
+ for (uint8_t PageWord = 0; PageWord < (SPM_PAGESIZE / 2); PageWord++)
{
/* Check if endpoint is empty - if so clear it and wait until ready for next packet */
if (!(Endpoint_BytesInEndpoint()))
break;
}
}
+
projects / pub / USBasp.git / blobdiff