Add multiple axis support to the HID joystick report in the HID_DESCRIPTOR_JOYSTICK...

[pub/USBasp.git] / Projects / AVRISP-MKII / AVRISP-MKII.txt

diff --git a/Projects/AVRISP-MKII/AVRISP-MKII.txt b/Projects/AVRISP-MKII/AVRISP-MKII.txt
index 7489cf6..c47a65e 100644 (file)
--- a/Projects/AVRISP-MKII/AVRISP-MKII.txt
+++ b/Projects/AVRISP-MKII/AVRISP-MKII.txt
@@ -6,7 +6,7 @@
 
 /** \mainpage AVRISP MKII Programmer Project
  *
- *  \section SSec_Compat Project Compatibility:
+ *  \section Sec_Compat Project Compatibility:
  *
  *  The following list indicates what microcontrollers are compatible with this project.
  *
@@ -15,7 +15,7 @@
  *  - Series 4 USB AVRs (ATMEGAxxU4)
  *  - Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - <i>8KB versions with reduced features only</i>
  *
- *  \section SSec_Info USB Information:
+ *  \section Sec_Info USB Information:
  *
  *  The following table gives a rundown of the USB utilization of this project.
  *
@@ -42,7 +42,7 @@
  *  </tr>
  * </table>
  *
- *  \section SSec_Description Project Description:
+ *  \section Sec_Description Project Description:
  *
  *  Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of
  *  microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its
@@ -57,7 +57,7 @@
  *    - No reversed/shorted target connector detection and notification
  *    - A separate header is required for each of the ISP, PDI and TPI programming protocols that the user wishes to use
  *
- *  On AVR models with an ADC converter, AVCC should be tied to 5V (e.g. VBUS) and the VTARGET_ADC_CHANNEL token should be
+ *  On AVR models with an ADC converter, AVCC should be tied to 5V (e.g. VBUS) and the \c VTARGET_ADC_CHANNEL token should be
  *  set to an appropriate ADC channel number in the project makefile for VTARGET detection to operate correctly. On models
  *  without an ADC converter, VTARGET will report a fixed 5V level at all times.
  *
@@ -109,8 +109,8 @@
  *  fuses have been mis-set. To use the recovery clock, connect the OCR1A pin of the USB AVR to the target AVR's
  *  XTAL1 pin, and set the ISP programming speed to 125KHz (note: other ISP speeds will not work correctly).
  *
- *  <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
- *  <b><sup>2</sup></b> <i>See AUX line related tokens in the \ref SSec_Options section</i>
+ *  <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n
+ *  <b><sup>2</sup></b> <i>See AUX line related tokens in the \ref Sec_Options section</i>
  *
  *  \section Sec_PDI PDI Connections
  *  Connections to the device for PDI programming (when enabled):
@@ -153,7 +153,7 @@
  *   </tr>
  *  </table>
  *
- *  <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
+ *  <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n
  *  <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n
  *
  *  \section Sec_TPI TPI Connections
@@ -197,11 +197,11 @@
  *   </tr>
  *  </table>
  *
- *  <b><sup>1</sup></b> <i>Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only</i> \n
+ *  <b><sup>1</sup></b> <i>Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only</i> \n
  *  <b><sup>2</sup></b> <i>The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors</i> \n
- *  <b><sup>3</sup></b> <i>See AUX line related tokens in the \ref SSec_Options section</i>
+ *  <b><sup>3</sup></b> <i>See AUX line related tokens in the \ref Sec_Options section</i>
  *
- *  \section SSec_Options Project Options
+ *  \section Sec_Options Project Options
  *
  *  The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
  *
@@ -267,6 +267,13 @@
  *        to the ADC. <i>Ignored when compiled for targets lacking an ADC, or when NO_VTARGET_DETECT is defined.</i></td>
  *   </tr>
  *   <tr>
+ *    <td>VTARGET_USE_INTERNAL_REF</td>
+ *    <td>Makefile LUFA_OPTS</td>
+ *    <td>Selects the internal 2.56V ADC reference voltage, instead of using the AVR's VREF pin. When enabled, this option will
+ *        override the VTARGET_REF_VOLTS configuration option. <i>Ignored when compiled for targets lacking an ADC, or when
+ *        NO_VTARGET_DETECT is defined.</i></td>
+ *   </tr>
+ *   <tr>
  *    <td>VTARGET_SCALE_FACTOR</td>
  *    <td>Makefile LUFA_OPTS</td>
  *    <td>Indicates the target's supply voltage scale factor when applied to the ADC. A simple resistive divider can be used on the