3 * This file contains special DoxyGen information for the generation of the main page and other special
4 * documentation pages. It is not a project source file.
7 /** \page Page_ChangeLog Project Changelog
9 * \section Sec_ChangeLogXXXXXX Version XXXXXX
16 * - Fixed possible lockup in the CDC device class driver, when the host sends data that is a multiple of the
20 * \section Sec_ChangeLog090810 Version 090810
23 * - Added new class drivers and matching demos to the library for rapid application development
24 * - Added new PrinterHost demo (thanks to John Andrews)
25 * - Added USB Missle Launcher project, submitted by Dave Fletcher
26 * - Added new Benito Arduino Programmer project
27 * - Added incomplete device and host mode demos for later enhancement
28 * - Updated MassStorage device block write routines to use ping-pong Dataflash buffering to increase throughput by around 30%
29 * - Error status LEDs shown when device endpoint configuration fails to complete in all demos and projects
30 * - Added new USB_Host_SetDeviceConfiguration() convenience function for easy configuration selection of devices while in USB
32 * - Added new USB_Host_ClearPipeStall() convenience function to clear a stall condition on an attached device's endpoint
33 * - Added new USB_Host_GetDeviceDescriptor() convenience function to retrieve the attached device's Device descriptor
34 * - Added new Endpoint_ClearStatusStage() convenience function to assist with the status stages of control transfers
35 * - Added new USE_INTERNAL_SERIAL define for using the unique serial numbers in some AVR models as the USB device's serial number,
36 * added NO_INTERNAL_SERIAL compile time option to turn off new serial number reading code
37 * - Added new DATAFLASH_CHIP_MASK() macro to the Dataflash driver, which returns the Dataflash select mask for the given chip index
38 * - Added new HOST_STATE_WaitForDeviceRemoval host state machine state for non-blocking disabling of device communications until the
39 * device has been removed (for use when an error occurs or communications with the device have completed)
40 * - Added new FAST_STREAM_TRANSFERS compile time option for faster stream transfers via multiple bytes copied per stream loop
41 * - Added stdio stream demo code to the CDC device demos, to show how to create standard streams out of the virtual serial ports
42 * - Added new EEPROM and FLASH buffer versions of the Endpoint and Pipe stream functions
43 * - Added new USE_FLASH_DESCRIPTORS and FIXED_NUM_CONFIGURATIONS compile time options
44 * - Added support for the new ATMEGA32U2, ATMEGA16U2 and ATMEGA8U2 AVR models
45 * - Added new USB_DeviceState variable to keep track of the current Device mode USB state
46 * - Added new LEDs_ToggleLEDs() function to the LEDs driver
47 * - Added new Pipe_BoundEndpointNumber() and Pipe_IsEndpointBound() functions
48 * - Added new DEVICE_STATE_AS_GPIOR and HOST_STATE_AS_GPIOR compile time options
49 * - Added 404 Not Found errors to the webserver in the RNDIS demos to indicate invalid URLs
52 * - Deprecated psuedo-scheduler and removed dynamic memory allocator from the library (first no longer needed and second unused)
53 * - The device-mode CALLBACK_USB_GetDescriptor() function now has an extra parameter so that the memory space in which the requested
54 * descriptor is located can be specified. This means that descriptors can now be located in multiple memory spaces within a device.
55 * - Removed vague USB_IsConnected global - test USB_DeviceState or USB_HostState explicitly to gain previous functionality
56 * - Removed USB_IsSuspended global - test USB_DeviceState against DEVICE_STATE_Suspended instead
57 * - Extended USB_GetDeviceConfigDescriptor() routine to require the configuration number within the device to fetch
58 * - Dataflash_WaitWhileBusy() now always ensures that the dataflash is ready for the next command immediately after returning,
59 * no need to call Dataflash_ToggleSelectedChipCS() afterwards
60 * - Low level API MIDI device demo no longer blocks if a note change event is sent while the endpoint is not ready
61 * - Pipe_GetErrorFlags() now returns additional error flags for overflow and underflow errors
62 * - Pipe stream functions now automatically set the correct pipe token, so that bidirectional pipes can be used
63 * - Pipe_ConfigurePipe() now automatically defaults IN pipes to accepting infinite IN requests, this can still be changed by calling
64 * the existing Pipe_SetFiniteINRequests() function
65 * - Changed F_CLOCK entries in project makefiles to alias to F_CPU by default, as this is the most common case
66 * - Host mode demos now use sane terminal escape codes, so that text is always readable and events/program output is visually distinguished
67 * from oneanother using foreground colours
68 * - Internal per-device preprocessing conditions changed to per-device series rather than per-controller group for finer-grain
70 * - Interrupts are no longer disabled during the processing of Control Requests on the default endpoint while in device mode
71 * - AudioOutput demos now always output to board LEDs, regardless of output mode (removed AUDIO_OUT_LEDS project option)
72 * - Removed SINGLE_DEVICE_CONFIGURATION compile time option in favour of the new FIXED_NUM_CONFIGURATIONS option so that the exact number
73 * of device configurations can be defined statically
74 * - Removed VBUS events, as they are already exposed to the user application via the regular device connection and disconnection events
75 * - Renamed and altered existing events to properly seperate out Host and Device mode events
78 * - Changed bootloaders to use FLASHEND rather than the existence of RAMPZ to determine if far FLASH pointers are needed to fix
79 * bootloaders on some of the USB AVR devices where avr-libc erronously defines RAMPZ
80 * - Fixes to MassStorageHost for better device compatibility (increase command timeout, change MassStore_WaitForDataReceived()
81 * to only unfreeze and check one data pipe at a time) to prevent incorrect device enumerations and freezes while trasferring data
82 * - Make Pipe_ConfigurePipe() mask the given endpoint number against PIPE_EPNUM_MASK to ensure the endpoint IN direction bit is
83 * cleared to prevent endpoint type corruption
84 * - Fixed issue opening CDC-ACM ports on hosts when the CDC device tries to send data before the host has set the line encoding
85 * - Fixed USB_OPT_MANUAL_PLL option being ignored during device disconnects on some models (thanks to Brian Dickman)
86 * - Fixed documentation mentioning Pipe_GetCurrentToken() function when correct function name is Pipe_GetPipeToken()
87 * - Fixed ADC driver for the ATMEGA32U4 and ATMEGA16U4 (thanks to Opendous Inc.)
88 * - Fixed CDCHost demo unfreezing the pipes at the point of configuration, rather than use
89 * - Fixed MassStorage demo not clearing the reset flag when a Mass Storage Reset is issued while not processing a command
90 * - Fixed USB_Host_SendControlRequest() not re-suspending the USB bus when initial device ready-wait fails
91 * - Fixed USB Pad regulator not being disabled on some AVR models when the USB_OPT_REG_DISABLED option is used
92 * - Fixed Host mode to Device mode UID change not causing a USB Disconnect event when a device was connected
93 * - Fixed Mouse/Keyboard demos not performing the correct arithmetic on the Idle period at the right times (thanks to Brian Dickman)
94 * - Fixed GenericHID failing HID class tests due to incorrect Logical Minimum and Logical Maximum values (thanks to Søren Greiner)
95 * - Fixed incorrect PIPE_EPNUM_MASK mask causing pipe failures on devices with endpoint addresses of 8 and above (thanks to John Andrews)
96 * - Fixed report data alignment issues in the MouseHostWithParser demo when X and Y movement data size is not a multiple of 8 bits
97 * - Fixed HID Report Descriptor Parser not correctly resetting internal states when a REPORT ID element is encountered
98 * - Fixed incorrect BUTTONS_BUTTON1 for the STK526 target
99 * - Fixed RNDIS demos freezing when more than one connection was attempted simultaneously, causing memory corruption
100 * - Fixed USBtoSerial demo receiving noise from the USART due to pullup not being enabled
103 * \section Sec_ChangeLog090605 Version 090605
105 * - Fixed bug in RNDISEthernet and DualCDC demos not using the correct USB_ControlRequest structure for control request data
106 * - Fixed documentation showing incorrect USB mode support on the supported AVRs list
107 * - Fixed RNDISEthernet not working under Linux due to Linux requiring an "optional" RNDIS request which was unhandled
108 * - Fixed Mouse and Keyboard device demos not acting in accordance with the HID specification for idle periods (thanks to Brian Dickman)
109 * - Removed support for endpoint/pipe non-control interrupts; these did not act in the way users expected, and had many subtle issues
110 * - Fixed Device Mode not handling Set Feature and Clear Feature Chapter 9 requests that are addressed to the device (thanks to Brian Dickman)
111 * - Moved control endpoint interrupt handling into the library itself, enable via the new INTERRUPT_CONTROL_ENDPOINT token
112 * - Fixed CDCHost not clearing configured pipes and resetting configured pipes mask when a partially enumerated invalid CDC
113 * interface is skipped
114 * - Clarified the size of library tokens which accept integer values in the Compile Time Tokens page, values now use the smallest datatype
115 * inside the library that is able to hold their defined value to save space
116 * - Removed DESCRIPTOR_ADDRESS() macro as it was largely supurflous and only served to obfuscate code
117 * - Rewritten event system to remove all macros, to make user code clearer
118 * - Fixed incorrect ENDPOINT_EPNUM_MASK mask preventing endpoints above EP3 from being selected (thanks to Jonathan Oakley)
119 * - Removed STREAM_CALLBACK() macro - callbacks now use regular function definitions to clarify user code
120 * - Removed DESCRIPTOR_COMPARATOR() macro - comparators should now use regular function definitions to clarify user code
121 * - USB_IsConnected is now cleared before the USB_Disconnect() event is fired in response to VBUS being removed
122 * - Fixed incorrect PID value being used in the USBtoSerial project (thanks to Phill)
123 * - Deleted StdDescriptors.c, renamed USB_GetDescriptor() to CALLBACK_USB_GetDescriptor, moved ConfigDescriptor.c/.h from the
124 * LUFA/Drivers/USB/Class/ directory to LUFA/Drivers/USB/HighLevel/ in preperation for the new USB class APIs
125 * - Moved out each demos' functionality library files (e.g. Ring Buffer library) to /Lib directories for a better directory structure
126 * - Removed Tx interrupt from the USBtoSerial demo; now sends characters via polling to ensure more time for the Rx interrupt
127 * - Fixed possible enumeration errors from spinloops which may fail to exit if the USB connection is severed before the exit condition
131 * \section Sec_ChangeLog090510 Version 090510
133 * - Added new GenericHIDHost demo
134 * - Corrections to the KeyboardHost and MouseHost demos' pipe handling to freeze and unfreeze the data pipes at the point of use
135 * - KeyboardHost, MouseHost and GenericHIDHost demos now save and restore the currently selected pipe inside the pipe ISR
136 * - Changed GenericHID device demo to use the LUFA scheduler, added INTERRUPT_DATA_ENDPOINT and INTERRUPT_CONTROL_ENDPOINT compile
138 * - All comments in the library, bootloaders, demos and projects have now been spell-checked and spelling mistakes/typos corrected
139 * - Added new PIMA_DATA_SIZE() define to the Still Image Host demo
140 * - Add call to MassStore_WaitForDataReceived() in MassStore_GetReturnedStatus() to ensure that the CSW has been received in the
141 * extended MSC timeout period before continuing, to prevent long processing delays from causing the MassStore_GetReturnedStatus()
142 * to early-abort (thanks to Dmitry Maksimov)
143 * - Move StdRequestType.h, StreamCallbacks.h, USBMode.h from the LowLevel USB driver directory to the HighLevel USB driver directory,
144 * where they are more suited
145 * - Removed all binary constants and replaced with decimal or hexadecimal constants so that unpatched GCC compilers can still build the
146 * code without having to be itself patched and recompiled first
147 * - Added preprocessor checks and documentation to the bootloaders giving information about missing SIGNATURE_x defines due to
148 * outdated avr-libc versions.
149 * - Added support to the CDCHost demo for devices with multiple CDC interfaces which are not the correct ACM type preceding the desired
151 * - Fixed GenericHID demo not starting USB and HID management tasks when not using interrupt driven modes (thanks to Carl Kjeldsen)
152 * - Fixed RNDISEthenet demo checking the incorrect message field for packet size constraints (thanks to Jonathan Oakley)
153 * - Fixed WriteNextReport code in the GenericHIDHost demo using incorrect parameter types and not selecting the correct endpoint
154 * - Adjusted sample CTC timer calculations in the AudioOutput and AudioInput demos to match the CTC calculations in the AVR datasheet,
155 * and to fix instances where rounding caused the endpoint to underflow (thanks to Robin Theunis)
156 * - The USB_Host_SendControlRequest() function no longer automatically selects the Control pipe (pipe 0), so that other control type
157 * pipes can be used with the function
158 * - The USB Host management task now saves and restores the currently selected pipe before and after the task completes
159 * - Fixed GenericHIDHost demo report write routine incorrect for control type requests (thanks to Andrei Krainev)
160 * - Removed Endpoint_ClearCurrentBank() and Pipe_ClearCurrentBank() in favour of new Endpoint_ClearIN(), Endpoint_ClearOUT(),
161 * Pipe_ClearIN() and Pipe_ClearOUT() macros (done to allow for the detection of packets of zero length)
162 * - Renamed *_ReadWriteAllowed() macros to *_IsReadWriteAllowed() to remain consistent with the rest of the LUFA API
163 * - Endpoint_IsSetupReceived() macro has been renamed to Endpoint_IsSETUPReceived(), Endpoint_ClearSetupReceived() macro has been
164 * renamed to Endpoint_ClearSETUP(), the Pipe_IsSetupSent() macro has been renamed to Pipe_IsSETUPSent() and the
165 * Pipe_ClearSetupSent() macro is no longer applicable and should be removed - changes made to compliment the new endpoint and pipe
166 * bank management API
167 * - Updated all demos, bootloaders and projects to use the new endpoint and pipe management APIs (thanks to Roman Thiel from Curetis AG)
168 * - Updated library doxygen documentation, added groups, changed documentation macro functions to real functions for clarity
169 * - Removed old endpoint and pipe aliased read/write/discard routines which did not have an explicit endian specifier for clarity
170 * - Removed the ButtLoadTag.h header file, as no one used for its intended purpose anyway
171 * - Renamed the main Drivers/AT90USBXXX directory to Drivers/Peripheral, renamed the Serial_Stream driver to SerialStream
172 * - Fixed CDC and USBtoSerial demos freezing where buffers were full while still transmitting or receiving (thanks to Peter Hand)
173 * - Removed "Host_" section of the function names in ConfigDescriptor.h, as most of the routines can now be used in device mode on the
175 * - Renamed functions in the HID parser to have a "USB_" prefix and the acronym "HID" in the name
176 * - Fixed incorrect HID interface class and subclass values in the Mouse and KeyboardMouse demos (thanks to Brian Dickman)
177 * - Capitalised the "Descriptor_Search" and "Descriptor_Search_Comp" prefixes of the values in the DSearch_Return_ErrorCodes_t and
178 * DSearch_Comp_Return_ErrorCodes_t enums
179 * - Removed "ERROR" from the enum names in the endpoint and pipe stream error code enums
180 * - Renamed the USB_PowerOnErrorCodes_t enum to USB_InitErrorCodes_t, renamed the POWERON_ERROR_NoUSBModeSpecified enum value to
181 * USB_INITERROR_NoUSBModeSpecified
182 * - Renamed USB_PowerOnFail event to USB_InitFailure
183 * - Renamed OTG.h header functions to be more consistent with the rest of the library API
184 * - Changed over all deprecated GCC structure tag initializers to the standardized C99 format (thanks to Mike Alexander)
185 * - USB_HostRequest renamed to USB_ControlRequest, entire control request header is now read into USB_ControlRequest in Device mode
186 * rather than having the library pass only partially read header data to the application
187 * - The USB_UnhandledControlPacket event has had its parameters removed, in favour of accessing the new USB_ControlRequest structure
188 * - The Endpoint control stream functions now correctly send a ZLP to the host when less data than requested is sent
189 * - Fixed USB_RemoteWakeupEnabled flag never being set (the REMOTE WAKEUP Set Feature request was not being handled)
190 * - Renamed the FEATURELESS_CONTROL_ONLY_DEVICE compile-time token to CONTROL_ONLY_DEVICE
191 * - Endpoint configuration is now refined to give better output when all configurations have static inputs - removed the now useless
192 * STATIC_ENDPOINT_CONFIGURATION compile time token
193 * - Fixed SPI driver init function not clearing SPI2X bit when not needed
194 * - Fixed PREVENT ALLOW MEDIUM REMOVAL command issuing in the MassStorageHost demo using incorrect parameters (thanks to Mike Alex)
195 * - Fixed MassStorageHost demo broken due to an incorrect if statement test in MassStore_GetReturnedStatus()
196 * - Fixed reversed signature byte ordering in the CDC bootloader (thanks to Johannes Raschke)
197 * - Changed PIPE_CONTROLPIPE_DEFAULT_SIZE from 8 to 64 to try to prevent problems with faulty devices which do not respect the given
198 * wLength value when reading in the device descriptor
199 * - Fixed missing semicolon in the ATAVRUSBRF01 LED board driver code (thanks to Morten Lund)
200 * - Changed LED board driver code to define dummy LED masks for the first four board LEDs, so that user code can be compiled for boards
201 * with less than four LEDs without code modifications (thanks to Morten Lund)
202 * - Changed HWB board driver to Buttons driver, to allow for the support of future boards with more than one mounted GPIO button
203 * - Serial driver now correctly calculates the baud register value when in double speed mode
204 * - Init function of the Serial driver is now static inline to product smaller code for the common-case of static init values
207 * \section Sec_ChangeLog090401 Version 090401
209 * - Fixed MagStripe project configuration descriptor containing an unused (blank) endpoint descriptor
210 * - Incorporated makefile changes by Denver Gingerich to retain compatibility with stock (non-WinAVR) AVR-GCC installations
211 * - Fixed makefile EEPROM programming targets programming FLASH data in addition to EEPROM data
212 * - LUFA devices now enumerate correctly with LUFA hosts
213 * - Fixed Configuration Descriptor search routine freezing when a comparator returned a failure
214 * - Removed HID report item serial dump in the MouseHostWithParser and KeyboardHostWithParser - useful only for debugging, and
215 * slowed down the enumeration of HID devices too much
216 * - Increased the number of bits per track which can be read in the MagStripe project to 8192 when compiled for the AT90USBXXX6/7
217 * - Fixed KeyboardMouse demo discarding the wIndex value in the REQ_GetReport request
218 * - USBtoSerial demo now discards all Rx data when not connected to a USB host, rather than buffering characters for transmission
219 * next time the device is attached to a host.
220 * - Added new F_CLOCK compile time constant to the library and makefiles, to give the raw input clock (used to feed the PLL before any
221 * clock prescaling is performed) frequency, so that the PLL prescale mask can be determined
222 * - Changed stream wait timeout counter to be 16-bit, so that very long timeout periods can be set for correct communications with
223 * badly designed hosts or devices which greatly exceed the USB specification limits
224 * - Mass Storage Host demo now uses a USB_STREAM_TIMEOUT_MS of two seconds to maintain compatibility with poorly designed devices
225 * - Function attribute ATTR_ALWAYSINLINE renamed to ATTR_ALWAYS_INLINE to match other function attribute macro naming conventions
226 * - Added ATTR_ALWAYS_INLINE attribute to several key inlined library components, to ensure they are inlined in all circumstances
227 * - Removed SetSystemClockPrescaler() macro, the clock_prescale_set() avr-libc macro has been corrected in recent avr-libc versions
228 * - Fixed incorrect/missing control status stage transfers on demos, bootloaders and applications (thanks to Nate Lawson)
229 * - The NO_CLEARSET_FEATURE_REQUEST compile time token has been renamed to FEATURELESS_CONTROL_ONLY_DEVICE, and its function expanded
230 * to also remove parts of the Get Status chapter 9 request to further reduce code usage
231 * - Makefile updated to include output giving the currently selected BOARD parameter value
232 * - Board Dataflash driver now allows for dataflash ICs which use different shifts for setting the current page/byte address (thanks
234 * - Added DataflashManager_WriteBlocks_RAM() and DataflashManager_ReadBlocks_RAM() functions to the MassStorage demo, to allow for easy
235 * interfacing with a FAT library for dataflash file level access
236 * - Corrected CDC class bootloader to fix a few bugs, changed address counter to store x2 addresses for convenience
237 * - Fixed typos in the SPI driver SPI_SPEED_FCPU_DIV_64 and SPI_SPEED_FCPU_DIV_128 masks (thanks to Markus Zocholl)
238 * - Keyboard and Mouse device demos (normal, data interrupt and fully interrupt driven) combined into unified keyboard and mouse demos
239 * - Keyboard and Mouse host demos (normal and data interrupt driven) combined into unified keyboard and mouse demos
240 * - Removed AVRISP_Programmer project due to code quality concerns
241 * - Fixed CDC demo not sending an empty packet after each transfer to prevent the host from buffering incoming data
242 * - Fixed documentation typos and preprocessor checks relating to misspellings of the USE_RAM_DESCRIPTORS token (thanks to Ian Gregg)
243 * - Fixed USBTask.h not conditionally including HostChapter9.h only when USB_CAN_BE_HOST is defined (thanks to Ian Gregg)
244 * - Fixed incorrect ADC driver init register manipulation (thanks to Tobias)
245 * - Added new GenericHID device demo application
246 * - Fixed Still Image Host SImage_SendData() function not clearing the pipe bank after sending data
249 * \section Sec_ChangeLog090209 Version 090209
251 * - PWM timer mode in AudioOut demo changed to Fast PWM for speed
252 * - Updated Magstripe project to work with the latest hardware revision
253 * - Fixed library not responding to the BCERRI flag correctly in host mode, leading to device lockups
254 * - Fixed library handling Get Descriptor requests when not addressed as standard requests to the device or interface (thanks to
256 * - Fixed serious data corruption issue in MassStorage demo dataflash write routine
257 * - Added new NO_CLEARSET_FEATURE_REQUEST compile time token
258 * - USB task now restores previous global interrupt state after execution, rather than forcing global interrupts to be enabled
259 * - Fixed USB_DeviceEnumerationComplete event firing after each configuration change, rather than once after the initial configuration
260 * - Added ENDPOINT_DOUBLEBANK_SUPPORTED() macros to Endpoint.h, altered ENDPOINT_MAX_SIZE() to allow user to specify endpoint
261 * - ENDPOINT_MAX_ENDPOINTS changed to ENDPOINT_TOTAL_ENDPOINTS, PIPE_MAX_PIPES changed to PIPE_TOTAL_PIPES
262 * - Endpoint and Pipe non-control stream functions now ensure endpoint or pipe is ready before reading or writing
263 * - Changed Teensy bootloader to use a watchdog reset when exiting rather than a software jump
264 * - Fixed integer promotion error in MassStorage and MassStorageHost demos, corrupting read/write transfers
265 * - SPI_SendByte is now SPI_TransferByte, added new SPI_SendByte and SPI_ReceiveByte functions for fast one-way transfer
266 * - MassStorage demo changed to use new fast one-way SPI transfers to increase throughput
267 * - MassStorage handling of Mass Storage Reset class request improved
268 * - Altered MassStorage demo dataflash block read code for speed
269 * - Added USB_IsSuspended global flag
270 * - Simplified internal Dual Mode (OTG) USB library code to reduce code size
271 * - Extended stream timeout period to 100ms from 50ms
272 * - Mass Storage Host demo commands now all return an error code from the Pipe_Stream_RW_ErrorCodes_t enum
273 * - Added SubErrorCode parameter to the USB_DeviceEnumerationFailed event
274 * - VBUS drop interrupt now disabled during the manual-to-auto VBUS delivery handoff
275 * - Simplified low level backend so that device/host mode initialization uses the same code paths
276 * - Added workaround for faulty Mass Storage devices which do not implement the required GET_MAX_LUN request
277 * - Removed buggy Telnet application from the RNDIS demo
278 * - Moved Mass Storage class requests in the Mass Storage Host demo to wrapper functions in MassStoreCommands.c
279 * - Fixed incorrect SCSI command size value in the Request Sense command in MassStoreCommands.c
280 * - Added SetProtocol request to HID class non-parser Mouse and Keyboard demos to force devices to use the correct Boot Protocol
281 * - Added new "dfu" and "flip" programming targets to project makefiles
282 * - HID_PARSE_Sucessful enum member typo corrected to HID_PARSE_Successful
283 * - Changed COLLECTION item structures in the HID descriptor parser to include the collection's Usage Page value
284 * - Serial driver now sets Tx line as output, enables pullup on Rx line
285 * - Fixed smaller USB AVRs raising multiple connection and disconnection events when NO_LIMITED_CONTROLLER_CONNECT is disabled
286 * - Added HOST_DEVICE_SETTLE_DELAY_MS to give the host delay after a device is connected before it is enumerated
287 * - Fixed KeyboardHostWithParser demo linking against the wrong global variables
288 * - Completed doxygen documentation of remaining library bootloaders, demos and projects
289 * - Fixed incorrect bootloader start address in the TeensyHID bootloader
290 * - Added HWB button whole-disk ASCII dump functionality to MassStoreHost demo
291 * - Replaced printf_P(PSTR("%c"), {Variable}) calls with putchar(<Variable>) for speed and size savings
292 * - Serial driver now accepts baud rates over 16-bits in size, added double speed flag option
293 * - Fixed incorrect callback abort return value in Pipe.c
294 * - Added new flip-ee and dfu-ee makefile targets (courtesy of Opendous Inc.)
295 * - Removed reboot-on-disconnect code from the TeensyHID bootloader, caused problems on some systems
296 * - Fixed AudioOutput and AudioInput demos looping on the endpoint data, rather than processing a sample at a time and returning
297 * each time the task runs to allow for other tasks to execute
298 * - Added support for the Atmel ATAVRUSBRF01 board
299 * - Added AVRISP Programmer Project, courtesy of Opendous Inc.
300 * - Fixed CDC Host demo not searching through both CDC interfaces for endpoints
301 * - Fixed incorrect Product String descriptor length in the DFU class bootloader
304 * \section Sec_ChangeLog081224 Version 081224
306 * - MyUSB name changed to LUFA, the Lightweight USB Framework for AVRs
307 * - Fixed Mass Storage Host demo's MassStore_SendCommand() delay in the incorrect place
308 * - Fixed USBtoSerial demo not calling ReconfigureUSART() after a change in the line encoding
309 * - Fixed infinite loop in host mode Host-to-Device control transfers with data stages
310 * - HID report parser now supports devices with multiple reports in one interface via Report IDs
311 * - Fixed RZUSBSTICK board LED driver header incorrect macro definition order causing compile errors
312 * - Calling USB_Init() when the USB interface is already configured now forces a complete interface reset
313 * and re-enumeration - fixes MyUSB DFU bootloader not switching to app code correctly when soft reset used
314 * - Fixed "No newline at end of file" warning when stream callbacks are enabled
315 * - DFU bootloader now uses fixed signature bytes per device, rather than reading them out dynamically for size
316 * - Added new FIXED_CONTROL_ENDPOINT_SIZE and USE_SINGLE_DEVICE_CONFIGURATION switches to statically define certain values to
317 * reduce compiled binary size
318 * - Added new NO_LIMITED_CONTROLLER_CONNECT switch to prevent the library from trying to determine bus connection
319 * state from the suspension and wake up events on the smaller USB AVRs
320 * - Added summary of all library compile time tokens to the documentation
321 * - Added overview of the LUFA scheduler to the documentation
322 * - Removed MANUAL_PLL_CONTROL compile time token, replaced with a mask for the USB_Init() Options parameter
323 * - CDC bootloader now uses the correct non-far or far versions of the pgm_* functions depending on if RAMPZ is defined
324 * - Doxygen documentation now contains documentation on all the projects, bootloaders and most demos included with the library
325 * - CDC bootloader now runs user application when USB disconnected rather than waiting for a hard reset
326 * - MouseHostWithParser and KeyboardHostWithParser now support multiple-report devices
327 * - RNDIS demo can now close connections correctly using the new TCP_APP_CLOSECONNECTION() macro - used in Webserver
328 * - Fixed the DFU bootloader, no longer freezes up when certain files are programmed into an AVR, made reading/writing faster
329 * - Fixed mouse/joystick up/down movements reversed - HID mouse X/Y coordinates use a left-handed coordinate system, not a normal
330 * right-handed system
331 * - Added stub code to the CDC and USBtoSerial demos showing how to read and set the RS-232 handshake lines - not currently used in
332 * the demos, but the example code and supporting defines are now in place
333 * - Interrupts are now disabled when processing a control request in device mode, to avoid exceeding the strict control request
334 * timing requirements.
335 * - All demos now use a central StatusUpdate() function rather than direct calls to the board LED functions, so that the demos can
336 * easily be altered to show different LED combinations (or do something else entirely) as the demo's status changes
337 * - Removed LED commands from the CDC bootloader, unused by most AVR910 programming software
338 * - Fixed RNDIS demo ICMP ping requests echoing back incorrect data
339 * - Added DHCP server code to RNDIS demo, allowing for hands-free auto configuration on any PC
340 * - Fixed DFU bootloader PID value for the ATMEGA16U4 AVR
341 * - Endpoint and Pipe configuration functions now return an error code indicating success or failure
342 * - USB Reset in device mode now resets and disables all device endpoints
343 * - Added intermediate states to the host mode state machine, reducing the USB task blocking time to no more than 1ms explicitly per
344 * invocation when in host mode
345 * - Added support for the ATMEGA32U6 microcontroller
346 * - Added STATIC_ENDPOINT_CONFIGURATION compile time option, enabled in the bootloaders to minimize space usage
347 * - Removed redundant code from the USB device GetStatus() chapter 9 processing routine
348 * - Added new TeensyHID bootloader, compatible with the Teensy HID protocol (http://www.pjrc.com/teensy/)
349 * - Versions are now numbered by release dates, rather than arbitrary major/minor revision numbers
350 * - USB_RemoteWakeupEnabled is now correctly set and cleared by SetFeature and ClearFeature requests from the host
351 * - Changed prototype of GetDescriptor, so that it now returns the descriptor size (or zero if the descriptor doesn't exist)
352 * rather than passing the size back to the caller through a parameter and returning a boolean
355 * \section Sec_ChangeLog153 Version 1.5.3 - Released 2nd October, 2008
357 * - Fixed CDC bootloader using pgmspace macros for some descriptors inappropriately
358 * - Updated all Mouse and Keyboard device demos to include boot protocol support (now works in BIOS)
359 * - Renamed bootloader directories to remove spaces, which were causing build problems on several OSes
360 * - Removed serial number strings from all but the MassStore demo where it is required - users were not
361 * modifying the code to either omit the descriptor or use a unique serial per device causing problems
362 * when multiple units of the same device were plugged in at the same time
363 * - AudioOutput and AudioInput demos now correctly silence endpoints when not enabled by the host
364 * - Added KeyboardMouse demo (Keyboard and Mouse functionality combined into a single demo)
365 * - Added DriverStubs directory to house board level driver templates, to make MyUSB compatible custom board
366 * driver creation easier
367 * - Extended MassStorage demo to support multiple LUNs, 2 by default
368 * - Fixed incorrect device address mask, preventing the device from enumerating with addresses larger than 63
369 * - Fixed incorrect data direction mask in the GetStatus standard request, preventing it from being handled
370 * - Fixed incorrect GetStatus standard request for endpoints, now returns the endpoint STALL status correctly
371 * - Added in new USB_RemoteWakeupEnabled and USB_CurrentlySelfPowered flags rather than using fixed values
372 * - Added DualCDC demo to demonstrate the use of Interface Association Descriptors
373 * - Added pipe NAK detection and clearing API
374 * - Added pipe status change (NAK, STALL, etc.) interrupt API
375 * - Fixed MassStorageHost demo so that it no longer freezes randomly when issuing several commands in a row
376 * - Host demos configuration descriptor routines now return a unique error code when the returned data does
377 * not have a valid configuration descriptor header
378 * - Added Endpoint_WaitUntilReady() and Pipe_WaitUntilReady() functions
379 * - Stream functions now have software timeouts, timeout period can be set by the USB_STREAM_TIMEOUT_MS token
380 * - All demos now pass the USB.org automated Chapter 9 device compliance tests
381 * - All HID demos now pass the USB.org automated HID compliance tests
382 * - Polling interval of the interrupt endpoint in the CDC based demos changed to 0xFF to fix problems on Linux systems
383 * - Changed stream functions to accept a new callback function, with NO_STREAM_CALLBACKS used to disable all callbacks
384 * - Mass Storage demo dataflash management routines changed to use the endpoint stream functions
385 * - Added AVRStudio project files for each demo in addition to the existing Programmer's Notepad master project file
386 * - Re-added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes
387 * are reflected in the hardware (change was previously lost)
390 * \section Sec_ChangeLog152 Version 1.5.2 - Released 31st July, 2008
392 * - Fixed SwapEndian_32() function in Common.h so that it now works correctly (wrong parameter types)
393 * - Updated RNDIS demo - notification endpoint is no longer blocking so that it works with faulty Linux RNDIS
394 * implementations (where the notification endpoint is ignored in favour of polling the control endpoint)
395 * - Fixed incorrect Vendor Description string return size in RNDIS demo for the OID_GEN_VENDOR_DESCRIPTION OID token
396 * - Added very basic TCP/IP stack and HTTP/TELNET servers to RNDIS demo
397 * - Fixed DFU bootloader exit causing programming software to complain about failed writes
398 * - Fixed DFU bootloader EEPROM programming mode wiping first flash page
399 * - Fixed Clear/Set Feature device standard request processing code (fixing MassStorage demo in the process)
400 * - Added support for the ATMEGA16U4 AVR microcontroller
401 * - Library licence changed from LGPLv3 to MIT license
404 * \section Sec_ChangeLog151 Version 1.5.1 - Released 31st July, 2008
406 * - Changed host demos to enable the host function task on the firing of the USB_DeviceEnumerationComplete event
407 * rather than the USB_DeviceAttached event
408 * - HID Usage Stack now forcefully cleared after an IN/OUT/FEATURE item has been completely processed to remove
409 * any referenced but not created usages
410 * - Changed USB_INT_DisableAllInterrupts() and USB_INT_ClearAllInterrupts(), USB_Host_GetNextDescriptorOfType(),
411 * USB_Host_GetNextDescriptorOfTypeBefore(), USB_Host_GetNextDescriptorOfTypeAfter() to normal functions (from inline)
412 * - Fixed USBtoSerial demo not sending data, only receiving
413 * - Fixed main makefile to make all by default, fixed MagStripe directory case to prevent case-sensitive path problems
414 * - ConfigDescriptor functions made normal, instead of static inline
415 * - Pipe/Endpoint *_Ignore_* functions changed to *_Discard_*, old names still present as aliases
416 * - Fixed ENDPOINT_MAX_SIZE define to be correct on limited USB controller AVRs
417 * - Changed endpoint and pipe size translation routines to use previous IF/ELSE IF cascade code, new algorithmic
418 * approach was buggy and caused problems
419 * - Bootloaders now compile with -fno-inline-small-functions option to reduce code size
420 * - Audio demos now use correct endpoint sizes for full and limited controller USB AVRs, double banking in all cases
421 * to be in line with the specification (isochronous endpoints MUST be double banked)
422 * - Added Interface Association descriptor to StdDescriptors.h, based on the relevant USB2.0 ECN
423 * - Fixed MIDI demo, corrected Audio Streaming descriptor to follow the MIDI-specific AS structure
424 * - Fixed HID class demo descriptors so that the HID interface's protocol is 0x00 (required for non-boot protocol HID
425 * devices) to prevent problems on hosts expecting the boot protocol functions to be supported
426 * - Added read/write control stream functions to Endpoint.h
427 * - Fixed AudioOut demo not setting port pins to inputs on USB disconnect properly
428 * - Added RNDISEthernet demo application
431 * \section Sec_ChangeLog150 Version 1.5.0 - Released 10 June, 2008
433 * - Fixed MIDI demo, now correctly waits for the endpoint to be ready between multiple note messages
434 * - Added CDC Host demo application
435 * - Added KeyboardFullInt demo application
436 * - Endpoint and Pipe creation routines now mask endpoint/pipe size with the size mask, to remove transaction
437 * size bits not required for the routines (improves compatibility with devices)
438 * - Fixed AudioInput demo - now correctly sends sampled audio to the host PC
439 * - Fixed AudioOutput demo once more -- apparently Windows requires endpoint packets to be >=192 bytes
440 * - Shrunk round-robbin scheduler code slightly via the use of struct pointers rather than array indexes
441 * - Fixed off-by-one error when determining if the Usage Stack is full inside the HID Report parser
442 * - Renamed Magstripe.h to MagstripeHW.h and moved driver out of the library and into the MagStripe demo folder
443 * - Added preprocessor checks to enable C linkage on the library components when used with a C++ compiler
444 * - Added Still Image Host demo application
445 * - The USB device task now restores the previously selected endpoint, allowing control requests to be transparently
446 * handled via interrupts while other endpoints are serviced through polling
447 * - Fixed device signature being sent in reverse order in the CDC bootloader
448 * - Host demos now have a separate ConfigDescriptor.c/.h file for configuration descriptor processing
449 * - HostWithParser demos now have a separate HIDReport.c/.h file for HID report processing and dumping
450 * - Removed non-mandatory commands from MassStorage demo to save space, fixed SENSE ResponseCode value
451 * - CDC demos now send empty packets after sending a full one to prevent buffering issues on the host
452 * - Updated demo descriptors to use VID/PID values donated by Atmel
453 * - Added DoxyGen documentation to the source files
454 * - Fixed Serial_IsCharRecieved() definition, was previously reversed
455 * - Removed separate USB_Descriptor_Language_t descriptor, USB_Descriptor_String_t is used instead
456 * - Removed unused Device Qualifier descriptor structure
457 * - Renamed the USB_CreateEndpoints event to the more appropriate USB_ConfigurationChanged
458 * - Fixed MassStorageHost demo reading in the block data in reverse
459 * - Removed outdated typedefs in StdRequestType.h, superseded by the macro masks
460 * - Corrected OTG.h is now included when the AVR supports both Host and Device modes, for creating OTG products
461 * - USB_DeviceEnumerationComplete event is now also fired when in device mode and the host has finished its enumeration
462 * - Interrupt driven demos now properly restore previously selected endpoint when ISR is complete
463 * - USB_HOST_TIMEOUT_MS is now overridable in the user project makefile to a custom fixed timeout value
464 * - Renamed USB_Host_SOFGeneration_* macros to more friendly USB_Host_SuspendBus(), USB_Host_ResumeBus()
465 * and USB_Host_IsBusSuspended()
466 * - Renamed *_*_Is* macros to *_Is* to make all flag checking macros consistent, Pipe_SetInterruptFreq() is now
467 * Pipe_SetInterruptPeriod() to use the correct terminology
468 * - UnicodeString member of USB_Descriptor_String_t struct changed to an ordinary int array type, so that the GCC
469 * Unicode strings (prefixed with an L before the opening quotation mark) can be used instead of explicit arrays
470 * of ASCII characters
471 * - Fixed Endpoint/Pipes being configured incorrectly if the maximum endpoint/pipe size for the selected USB AVR
472 * model was given as the bank size
473 * - HID device demos now use a true raw array for the HID report descriptor rather than a struct wrapped array
474 * - Added VERSION_BCD() macro, fixed reported HID and USB version numbers in demo descriptors
475 * - Cleaned up GetDescriptor device chapter 9 handler function
476 * - Added GET_REPORT class specific request to HID demos to make them complaint to the HID class
477 * - Cleaned up setting of USB_IsInitialized and USB_IsConnected values to only when needed
478 * - Removed Atomic.c and ISRMacro.h; the library was already only compatible with recent avr-lib-c for other reasons
479 * - All demos and library functions now use USB standardized names for the USB data (bRequest, wLength, etc.)
480 * - Added USE_NONSTANDARD_DESCRIPTOR_NAMES token to switch back to the non-standard descriptor element names
483 * \section Sec_ChangeLog141 Version 1.4.1 - Released 5 May, 2008
485 * - Enhanced KeyboardWithParser demo, now prints out pressed alphanumeric characters like the standard demo
486 * - Fixed MassStorage demo, read/writes using non mode-10 commands now work correctly
487 * - Corrected version number in Version.h
490 * \section Sec_ChangeLog140 Version 1.4.0 - Released 5 May, 2008
492 * - Added HID Report Parser API to the library
493 * - Added Mouse and Keyboard host demo applications, using the new HID report parser engine
494 * - Added MouseFullInt demo, which demonstrates a fully interrupt (including control requests) mouse device
495 * - Fixed incorrect length value in the audio control descriptor of the AudioOutput and AudioInput demos
496 * - Added MIDI device demo application to the library
497 * - Fixed problem preventing USB devices from being resumed from a suspended state
498 * - Added new CDC class bootloader to the library, based on the AVR109 bootloader protocol
499 * - Added header to each demo application indicating the mode, class, subclass, standards used and supported speed
500 * - Functions expecting endpoint/pipe numbers are no longer automatically masked against ENDPOINT_EPNUM_MASK or
501 * PIPE_PIPENUM_MASK - this should be manually added to code which requires it
502 * - Fixed DFU class bootloader - corrected frequency of flash page writes, greatly reducing programming time
503 * - Renamed AVR_HOST_GetDeviceConfigDescriptor() to USB_Host_GetDeviceConfigDescriptor() and AVR_HOST_GetNextDescriptor()
504 * to USB_Host_GetNextDescriptor()
505 * - Added new USB_Host_GetNextDescriptorOfTypeBefore() and USB_Host_GetNextDescriptorOfTypeAfter() routines
506 * - Moved configuration descriptor routines to MyUSB/Drivers/USB/Class/, new accompanying ConfigDescriptors.c file
507 * - Added new configuration descriptor comparator API for more powerful descriptor parsing, updated host demos to use the
509 * - Fixed MassStorageHost demo capacity printout, and changed data read/write mode from little-endian to the correct
510 * big-endian for SCSI devices
511 * - Fixed macro/function naming consistency; USB_HOST is now USB_Host, USB_DEV is now USB_Device
512 * - Added better error reporting to host demos
513 * - Added 10 microsecond delay after addressing devices in host mode, to prevent control stalls
516 * \section Sec_ChangeLog132 Version 1.3.2 - Released April 1st, 2008
518 * - Added call to ReconfigureUSART() in USBtoSerial SetLineCoding request, so that baud rate changes
519 * are reflected in the hardware
520 * - Fixed CDC and USBtoSerial demos - Stream commands do not work for control endpoints, and the
521 * GetLineCoding request had an incorrect RequestType mask preventing it from being processed
522 * - Improved reliability of the USBtoSerial demo, adding a busy wait while the buffer is full
523 * - Device control endpoint size is now determined from the device's descriptors rather than being fixed
524 * - Separated out SPI code into new SPI driver in AT90USBXXX driver directory
525 * - Bootloader now returns correct PID for the selected USB AVR model, not just the AT90USB128X PID
526 * - Added support for the RZUSBSTICK board
527 * - Bicolour driver removed in favour of generic LEDs driver
528 * - Added support for the ATMEGA32U4 AVR
529 * - Added MANUAL_PLL_CONTROL compile time option to prevent the USB library from manipulating the PLL
532 * \section Sec_ChangeLog131 Version 1.3.1 - Released March 19th 2008
534 * - Fixed USB to Serial demo - class value in the descriptors was incorrect
535 * - Control endpoint size changed from 64 bytes to 8 bytes to save on USB FIFO RAM and to allow low
536 * speed mode devices to enumerate properly
537 * - USB to Serial demo data endpoints changed to dual-banked 16 byte to allow the demo to work
538 * on USB AVRs with limited USB FIFO RAM
539 * - Changed demo endpoint numbers to use endpoints 3 and 4 for double banking, to allow limited
540 * USB device controller AVRs (AT90USB162, AT90USB82) to function correctly
541 * - Updated Audio Out demo to use timer 1 for AVRs lacking a timer 3 for the PWM output
542 * - Fixed incorrect USB_DEV_OPT_HIGHSPEED entry in the Mass Storage device demo makefile
543 * - Optimized Mass Storage demo for a little extra transfer speed
544 * - Added LED indicators to the Keyboard demo for Caps Lock, Num Lock and Scroll Lock
545 * - Added Endpoint_Read_Stream, Endpoint_Write_Stream, Pipe_Read_Stream and Pipe_Write_Stream functions
546 * (including Big and Little Endian variants)
547 * - Made Dataflash functions inline for speed, removed now empty Dataflash.c driver file
548 * - Added new SetSystemClockPrescaler() macro (thanks to Joerg Wunsch)
549 * - Fixed Endpoint_ClearStall() to function correctly on full USB controller AVRs (AT90USBXXX6/7)
550 * - Endpoint_Setup_In_Clear() and Endpoint_Setup_Out_Clear() no longer set FIFOCON, in line with the
551 * directives in the datasheet
552 * - Fixed PLL prescaler defines for all AVR models and frequencies
553 * - Fixed ENDPOINT_INT_IN and ENDPOINT_INT_OUT definitions
554 * - Added interrupt driven keyboard and mouse device demos
555 * - Combined USB_Device_ClearFeature and USB_Device_SetFeature requests into a single routine for code
557 * - Added missing Pipe_GetCurrentPipe() macro to Pipe.h
560 * \section Sec_ChangeLog130 Version 1.3.0 - Released March 7th 2008
562 * - Unnecessary control endpoint config removed from device mode
563 * - Fixed device standard request interpreter accidentally processing some class-specific requests
564 * - Added USE_RAM_DESCRIPTORS and USE_EEPROM_DESCRIPTORS compile time options to instruct the library
565 * to use descriptors stored in RAM or EEPROM rather than flash memory
566 * - All demos now disable watchdog on startup, in case it has been enabled by fuses or the bootloader
567 * - USB_DEV_OPT_LOWSPEED option now works correctly
568 * - Added ability to set the USB options statically for a binary size reduction via the USE_STATIC_OPTIONS
569 * compile time define
570 * - USB_Init no longer takes a Mode parameter if compiled for a USB device with no host mode option, or
571 * if forced to a particular mode via the USB_HOST_ONLY or USB_DEVICE_ONLY compile time options
572 * - USB_Init no longer takes an Options parameter if options statically configured by USE_STATIC_OPTIONS
573 * - Endpoint_Ignore_* and Pipe_Ignore_* made smaller by making the dummy variable non-volatile so that the
574 * compiler can throw away the result more efficiently
575 * - Added in an optional GroupID value to each scheduler entry, so that groups of tasks can once again be
576 * controlled by the new Scheduler_SetGroupTaskMode() routine
577 * - Added support for AT90USB162 and AT90USB82 AVR models
578 * - Added support for the STK525 and STK526 boards
579 * - Added support for custom board drivers to be supplied by selecting the board type as BOARD_USER, and
580 * placing board drivers in {Application Directory}/Board/
581 * - PLL is now stopped and USB clock is frozen when detached from host in device mode, to save power
582 * - Joystick defines are now in synch with the schematics - orientation will be rotated for the USBKEY
583 * - Fixed USB_DEV_IsUSBSuspended() - now checks the correct register
584 * - Fixed data transfers to devices when in host mode
585 * - Renamed USB_DEV_OPT_HIGHSPEED to USB_DEV_OPT_FULLSPEED and USB_HOST_IsDeviceHighSpeed() to
586 * USB_HOST_IsDeviceFullSpeed() to be in line with the official USB speed names (to avoid confusion with
587 * the real high speed mode, which is unavailable on the USB AVRs)
590 * \section Sec_ChangeLog120 Version 1.2.0 - Released February 4th, 2008
592 * - Added USB_DeviceEnumerationComplete event for host mode
593 * - Added new Scheduler_Init routine to preprepare the scheduler, so that tasks can be started and
594 * stopped before the scheduler has been started (via Scheduler_Start)
595 * - Connection events in both Device and Host mode are now interrupt-driven, allowing the USB management
596 * task to be stopped when the USB is not connected to a host or device
597 * - All demos updated to stop the USB task when not in use via the appropriate USB events
598 * - Mass Storage Host demo application updated to function correctly with all USB flash disks
599 * - Mass Storage Host demo application now prints out the capacity and number of LUNs in the attached
600 * device, and prints the first block as hexadecimal numbers rather than ASCII characters
601 * - Endpoint and Pipe clearing routines now clear the Endpoint/Pipe interrupt and status flags
602 * - Shifted error handling code in the host enum state machine to a single block, to reduce code complexity
603 * - Added in DESCRIPTOR_TYPE, DESCRIPTOR_SIZE and DESCRIPTOR_CAST macros to make config descriptor processing
604 * clearer in USB hosts and DESCRIPTOR_ADDRESS for convenience in USB devices
605 * - Added in alloca macro to common.h, in case the user is using an old version of avr-lib-c missing the macro
608 * \section Sec_ChangeLog130 Version 1.1.0 - Released January 25th 2008
610 * - Fixed DCONNI interrupt being enabled accidentally after a USB reset
611 * - Fixed DDISCI interrupt not being disabled when a device is not connected
612 * - Added workaround for powerless pullup devices causing false disconnect interrupts
613 * - Added USB_DeviceEnumerationFailed event for Host mode
614 * - AVR_HOST_GetDeviceConfigDescriptor routine no longer modifies ConfigSizePtr if a valid buffer
616 * - Added ALLOCABLE_BYTES to DynAlloc, and added code to make the size of key storage variables
617 * dependant on size of memory parameters passed in via the user project's makefile
618 * - Fixed incorrect device reset routine being called in USBTask
619 * - Devices which do not connect within the standard 300mS are now supported
620 * - Removed incorrect ATTR_PURE from Scheduler_SetTaskMode(), which was preventing tasks from being
621 * started/stopped, as well as USB_InitTaskPointer(), which was breaking dual device/host USB projects
622 * - Changed scheduler to use the task name rather than IDs for setting the task mode, eliminating the
623 * need to have a task ID list
624 * - ID transistion interrupt now raises the appropriate device/host disconnect event if device attached
625 * - Fixed double VBUS change (and VBUS -) event when detatching in device mode
626 * - Added ability to disable ANSI terminal codes by the defining of DISABLE_TERMINAL_CODES in makefile
627 * - Removed return from ConfigurePipe and ConfigureEndpoint functions - use Pipe_IsConfigured() and
628 * Endpoint_IsConfigured() after calling the config functions to determine success
projects / pub / USBasp.git / blob